Inhaltszusammenfassung zur Seite Nr. 1
KE-5T, KE-5TB,
KE-8T, KE-9TB, KE-17TB
PLASTIC-PALM
10BASE-T ETHERNET HUB
User’s Guide
Inhaltszusammenfassung zur Seite Nr. 2
FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio communications. Oper
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents INTRODUCTION................................ ................................ ............1 PRODUCT FEATURES.....................................................................1 THE FRONT PANEL OF PLASTIC-PALM HUBS......................2 THE REAR PANEL OF PLASTIC-PALM HUBS........................3 LED INDICATORS..........................................................................4 REAR PANEL INDICATORS............................................................5 Twisted-
Inhaltszusammenfassung zur Seite Nr. 4
Introduction Thank you for choosing the PLASTIC-PALM 10BASE-T Ethernet Hub. The hub was designed and manufactured to give you years of trouble-free and reliable service. The hub is designed for plug-and-play installation and easy management. The hub provides an Uplink connection for your network expansion via a RJ-45 connector, making it easy to link two or more hubs together. The hub features LINK/RX LEDs to show the connection and receive status of each twisted pair port. PWR and COL indica
Inhaltszusammenfassung zur Seite Nr. 5
The Front Panel of PLASTIC-PALM HUBs 5-port Ethernet Hub 5-port Ethernet Hub with BNC port 8-port Ethernet Hub 9-port Ethernet Hub with BNC port 2
Inhaltszusammenfassung zur Seite Nr. 6
17-port Ethernet Hub with BNC port The Rear Panel of PLASTIC-PALM HUBs 5-port Ethernet Hub 5-port Ethernet Hub with BNC port 8-port Ethernet Hub 3
Inhaltszusammenfassung zur Seite Nr. 7
9-port Ethernet Hub with BNC port 17-port Ethernet Hub with BNC port LED Indicators Power (PWR): This indicator lights green when the hub is receiving power, otherwise, it is off. Collision (COL): This indicator indicates data collisions on the respective Ethernet segments of the hub. Whenever a collision is detected, the respective COL indicator will briefly blink amber. Link/Receive: This indicator green when the port is (LINK/RX) connected to a Ethernet station , If the 4
Inhaltszusammenfassung zur Seite Nr. 8
station to which the hub is connected is powered off, or if there is a problem with the link, the LED will remain off. And the indicator blinking green when the data will be received to all other connected ports. BNC: This indicator blinking green when the data is transmitted. Rear Panel Indicators Twisted-pair Jacks Use these jacks connect stations to the hub. These are MDI-X (Medium Dependent Interface, Cross-Wired) jacks, which means you can use ordinary stright-through twisted-pair cables t
Inhaltszusammenfassung zur Seite Nr. 9
Power Jack For the External power adapter. 6
Inhaltszusammenfassung zur Seite Nr. 10
Installation Installing the Hub The site where you install the hub may greatly affect its performance. When installing, consider the following pointers: Install the hub in a fairly cool and dry place, for the acceptable temperature and humidity operating ranges. Install the hub in a site free from strong electromagnetic field generators (such as motors), vibration, dust, and direct exposure to sunlight. Leave at least 10 cm of space at the front and rear of the hub for ventilation. Install the
Inhaltszusammenfassung zur Seite Nr. 11
Cables and Connectors Cable characteristics: Category 3 or better unshielded twisted-pair or EIA/TIA-568 compliant, 100-ohm shielded twisted-pair data cable with 0.4 to 0.6 mm (22 to 26 AWG) wires in two or four twisted pairs (only two pairs--that is, four wires--are used for 10BASE-T ). Maximum segment length: 100 meters Connectors: RJ-45 Straight Twisted-Pair Cable Pinouts Contact MDI-X Signal MDI-II Signal 1 RD+ (receive) TD+ (transmit) 2 RD- (receive) TD- (transmit) 3 TD+ (transmit) RD+ (
Inhaltszusammenfassung zur Seite Nr. 12
Crossover Cables When making an uplink connection between one hub and another (or between a hub and a switch or bridge) using X -type jacks at both ends, you must use a crossover cable. In a crossover cable, two pairs of wires are switched at one end. Carry out the following steps to create a crossover twisted-pair cable: 1. Leave one end of the cable as-is, with the wiring on the RJ-45 connector unchanged. The wiring needs to be modified at one end only. 2. At the other end of the cable, conne
Inhaltszusammenfassung zur Seite Nr. 13
Specifications General Standards: IEEE 802.3 10BASE-T Ethernet repeater, and ANSI X3T9.5 twisted-pair transceiver Topology: Star Protocol: CSMA/CD Network Data Transfer Rate: Ethernet: 10Mbps Number of Ports : 4 x STP + 1 x BNC, 5 x STP, 8 x STP, 8 x STP + 1 x BNC, 16 x STP + 1 x BNC Network Media : Category 3 or better UTP cable, maximum length 100 meters. Environmental and Physical Power Adapter: 5, 8, 9-por
