Inhaltszusammenfassung zur Seite Nr. 1
Nortel CallPilot
1002rp Server Hardware
Installation
ATTENTION
Clicking on a PDF hyperlink takes you to the appropriate page. If necessary,
scroll up or down the page to see the beginning of the referenced section.
NN44200-300
.
Inhaltszusammenfassung zur Seite Nr. 2
Document status: Standard Document version: 01.01 Document date: 23 February 2007 Copyright © 2007, Nortel Networks All Rights Reserved. Sourced in Canada The information in this document is subject to change without notice. The statements, configurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this do
Inhaltszusammenfassung zur Seite Nr. 3
RADISYS is a trademark of Radisys Corporation. SLR4, SLR5, and TANDBERG are trademarks of Tandberg Data ASA. SYBASE is a trademark of Sybase, Inc. TEAC is a trademark of TEAC Corporation US ROBOTICS, the US ROBOTICS logo, and SPORTSTER are trademarks of US Robotics. WINZIP is a trademark of Nico Mark Computing, Inc. XEON is a trademark of Intel, Inc. All other trademarks and registered trademarks are the property of their respective owners. Information for Japan Japan Denan statement The followi
Inhaltszusammenfassung zur Seite Nr. 4
Inhaltszusammenfassung zur Seite Nr. 5
5 Publication History February 2007 CallPilot 5.0, Standard 01.01 of , 1002rp Server Hardware Installation is issued for general release Nortel CallPilot 1002rp Server Hardware Installation NN44200-300 01.01 Standard 5.0 23 February 2007 Copyright © 2007, Nortel Networks Nortel Networks Confidential .
Inhaltszusammenfassung zur Seite Nr. 6
6 Publication History Nortel CallPilot 1002rp Server Hardware Installation NN44200-300 01.01 Standard 5.0 23 February 2007 Copyright © 2007, Nortel Networks Nortel Networks Confidential .
Inhaltszusammenfassung zur Seite Nr. 7
7 Contents Chapter 1 How to get help 9 Chapter 2 1002rp server description 11 Server features 11 Slot assignments 15 Reference Documents 15 Network connectivity 18 Supported peripheral devices 21 Chapter 3 Preparing for installation 23 Installation overview 23 Unpacking the 1002rp server 26 Removing the front bezel and server cover 27 Inspecting the server interior 29 Chapter 4 Power supply installation 33 Safety precautions 33 Installing the second power supply module (AC or DC) 34 DC wire gaug
Inhaltszusammenfassung zur Seite Nr. 8
8 Contents Nortel CallPilot 1002rp Server Hardware Installation NN44200-300 01.01 Standard 5.0 23 February 2007 Copyright © 2007, Nortel Networks Nortel Networks Confidential .
Inhaltszusammenfassung zur Seite Nr. 9
9 Chapter 1 How to get help This section explains how to get help for Nortel products and services. Getting help from the Nortel Web site The best way to get technical support for Nortel products is from the Nortel Technical Support Web site: http://www.nortel.com/support This site provides quick access to software, documentation, bulletins, and tools to address issues with Nortel products. More specifically, the site enables you to: • download software, documentation, and product bulletins sea
Inhaltszusammenfassung zur Seite Nr. 10
10 Chapter 1 How to get help Getting help from a specialist by using an Express Routing Code To access some Nortel Technical Solutions Centers, you can use an Express Routing Code (ERC) to quickly route your call to a specialist in your Nortel product or service. To locate the ERC for your product or service, go to: http://www.nortel.com/erc Getting help through a Nortel distributor or reseller If you purchased a service contract for your Nortel product from a distributor or authorized reseller,
Inhaltszusammenfassung zur Seite Nr. 11
11 Chapter 2 1002rp server description In this chapter "Server features" (page 11) "Slot assignments" (page 15) "Network connectivity" (page 18) "Network connectivity" (page 18) "Supported peripheral devices" (page 21) Reference documents Server features Introduction This section provides a general overview of the 1002rp server. Server dimensions and weight Height 320 mm (12.5 in.) Width 483 mm (19 in.) Depth (distance from front to back) without front bezel 495 mm (19.5 in.) 533 mm (21 in.)
Inhaltszusammenfassung zur Seite Nr. 12
12 Chapter 2 1002rp server description Environmental specifications Environmental condition Specification Operating temperature 10 Cto 35 C (50 Fto 95 F) Maximum rate of change must not exceed 10 C (50 F) per hour. Non-operating (storage) temperature -40 Cto70 C (-40 F to 158 F) Non-operating humidity 95%, non-condensing at 30 C (86 F) Altitude 1829 m (6000 ft) Electrostatic discharge 15 kV or more Acoustic noise 50 dBA in a typical office ambient temperature (18 Cto
Inhaltszusammenfassung zur Seite Nr. 13
Server features 13 Alarm board The alarm board is located under the baseboard. It connects to the status display panel on the front. Rear panel diagram The following diagram shows the slot locations in the rear panel, and the power switch and power input for an AC server. The rest of the diagram is the same for AC or DC servers. Nortel CallPilot 1002rp Server Hardware Installation NN44200-300 01.01 Standard 5.0 23 February 2007 Copyright © 2007, Nortel Networks Nortel Networks Confidential .
Inhaltszusammenfassung zur Seite Nr. 14
14 Chapter 2 1002rp server description Overhead view of empty server showing PCI and ISA connectors The following diagram shows the location of the PCI, SBC, and ISA connectors inside the server. The view in the diagram is from the rear of the server. For slot assignments, see "Slot assignments" (page 15). You must be able to identify slot locations for later steps in the CallPilot installation. Nortel CallPilot 1002rp Server Hardware Installation NN44200-300 01.01 Standard 5.0 23 February 2007
Inhaltszusammenfassung zur Seite Nr. 15
Slot assignments 15 Slot assignments Introduction The slot assignment tables show the following: the physical location of boards inside the server, relative to other boards the order in which boards are installed (for example, board #1, 2, 3) how the boards are represented in some CallPilot Manager applications (such as the Maintenance Administration page) the maximum capacity for each switch connectivity Note: Your server can vary depending on what was ordered from Nortel. Therefore, yo
Inhaltszusammenfassung zur Seite Nr. 16
16 Chapter 2 1002rp server description Nortel CallPilot 1002rp Server Hardware Installation NN44200-300 01.01 Standard 5.0 23 February 2007 Copyright © 2007, Nortel Networks Nortel Networks Confidential .
Inhaltszusammenfassung zur Seite Nr. 17
Slot assignments 17 Slot definition and slot numbering In these tables, the term slot refers to the available slot openings in the chassis, not the PCI or ISA connectors inside the server. Look at the server from the rear (see "Rear panel diagram" (page 13)). The slots are numbered from right to left, 1 to 20. Now, look at the server from the front. The slots are numbered from left to right. Note: For Meridian 1 and Communication Server 1000, the first MPB16-4 board must be installed in slot 11. Y
Inhaltszusammenfassung zur Seite Nr. 18
18 Chapter 2 1002rp server description Meridian 1*/ Communication Slot CallPilot-assigned Server* a number board label 1000 T1/SMDI Slot 13 (PCI Slot 5) BRD13 MPB16-4 #2 D/480JCT-2T1 (optional) Slot 14 (PCI Slot 6) BRD14 MPB16-4 #2 MPB96 board #2 (optional) or MPB96 (optional) #2 (optional) Slot 15 (PCI Slot 7) BRD15 MPB16-4 #2 D/480JCT-2T1 (optional) (optional) Slot 16 (PCI Slot 8) BRD16 MPB16-4 #2 D/480JCT-2T1 (optional) (optional) Slot 17 (PCI Slot 9) BRD17 MPB16-4 #2 MPB96 #3 (optional) (opt
Inhaltszusammenfassung zur Seite Nr. 19
Network connectivity 19 Sample network setup: Meridian 1 The following diagram shows a CallPilot server sample network setup with a Meridian 1 switch. The Meridian 1 switch can be one of the following: Option 11C or Option 11C Mini Option 51C Option 61C Options 81 and 81C Sample network setup: Communication Server 1000 The following diagram shows a CallPilot server network setup with a Communication Server 1000 system. Nortel CallPilot 1002rp Server Hardware Installation NN44200-300 01.0
Inhaltszusammenfassung zur Seite Nr. 20
20 Chapter 2 1002rp server description Switch connectivity For more details about how the 1002rp server and switch connection is established, refer to the Installation and Configuration Task List (NN44200-306). CallPilot ELAN subnet and Nortel server subnet setup The 1002rp server provides 10/100Base-T Ethernet connectivity through NICs installed in the server. See "Slot assignments" (page 15) for details on the location of NICs. The function of the NIC varies based on switch connectivity, as des
