Inhaltszusammenfassung zur Seite Nr. 1
NPort IA5150/5250 Series
User’s Manual
Second Edition, May 2006
www.moxa.com/product
Moxa Technologies Co., Ltd.
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231
Web: www.moxa.com
MOXA Technical Support
Worldwide: support@moxa.com.tw
The Americas support@moxa.com
Inhaltszusammenfassung zur Seite Nr. 2
NPort IA5150/5250 Series User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright © 2006 Moxa Technologies Co., Ltd. All rights reserved. Reproduction without permission is prohibited. Trademarks MOXA is a registered trademark of The Moxa Group. All other trademarks or registered marks in this manual belong to their respective manufacturers.
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents Chapter 1 Introduction ...............................................................................................1-1 Overview .............................................................................................................................. 1-2 Package Checklist................................................................................................................. 1-2 Product Features ..............................................................
Inhaltszusammenfassung zur Seite Nr. 4
Accessible IP Settings......................................................................................................... 5-31 Auto Warning Settings........................................................................................................ 5-32 Auto warning: E-mail and SNMP trap ....................................................................... 5-32 Event Type.............................................................................................................
Inhaltszusammenfassung zur Seite Nr. 5
1 1 Chapter 1 Introduction Welcome to the NPort IA Series of industrial serial device servers. In this manual, we refer to the seven products in the series collectively as “NPort IA5150/5250 Series.” The seven models in the NPort IA5150/5250 Series are: 1. NPort IA5150 1-port RS-232 (DB9), RS-422/485 (TB) to Ethernet Device Server 2. NPort IA5150I 1-port RS-232 (DB9), RS-422/485 (TB) to Ethernet Device Server, w/ 2KV Isolation protection 3. NPort IA5150-M-SC 1-port RS-232 (DB9), RS-4
Inhaltszusammenfassung zur Seite Nr. 6
NPort IA5150/5250 Series User’s Manual Introduction Overview The NPort IA5150/5250 series of device servers deliver easy and reliable serial-to-Ethernet connectivity for the industrial automation market. The NPort IA5150/5250 series is designed to allow any serial device to connect to an Ethernet network. The compact size of NPort IA device servers makes them an ideal choice for connecting RS-232/422/485 serial devices, such as PLCs, sensors, meters, motors, drives, barcode readers, and op
Inhaltszusammenfassung zur Seite Nr. 7
NPort IA5150/5250 Series User’s Manual Introduction Product Specifications NPort IA5150-M-SC/5150I-M-SC/5150-S-SC/5150I-S-SC LAN Fiber Port 1 100BaseFX port (SC connector) NPort IA5150/5150I/5250 LAN Ethernet Switch Ports 2 10/100BaseT(X) ports (RJ45 connector) Protection Built-in 1.5 KV magnetic isolation Optical Fiber Distance Multi mode: 0 to 2 km, 1310 nm (62.5/125 µm, 500 MHz*km) Single mode: 0 to 40 km, 1310 nm (9/125 µm, 3.5 PS/(nm*km) Min. TX Output Multi mode: -20 dBm Sin
Inhaltszusammenfassung zur Seite Nr. 8
NPort IA5150/5250 Series User’s Manual Introduction Serial Communication Parameters Parity None, Even, Odd, Space, Mark Data Bits 5, 6, 7, 8 Stop Bit 1, 1.5, 2 Flow Control RTS/CTS (for RS-232 port only), XON/XOFF Transmission Speed 110 bps to 230.4 Kbps Software Features Protocols ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, Rtelnet, DNS, SNMP, HTTP, SMTP, SNTP Utilities NPort Administrator for Windows 95/98/ME/NT/2000/XP/2003 Real COM/TTY Drivers Windows 95/98/ME/NT/2000/XP/2003 COM
Inhaltszusammenfassung zur Seite Nr. 9
2 2 Chapter 2 Getting Started In this chapter, we give instructions on installing NPort IA5150/5250 device servers. Software installation is covered in subsequent chapters. The following topics are covered in this chapter: Panel Layout Connecting the Hardware Wiring Requirements Connecting the Power Grounding NPort IA5150/5250 Series Connecting to the Network Connecting to a Serial Device LED Indicators
Inhaltszusammenfassung zur Seite Nr. 10
P1 RS-232/422/485 P2 RS-232 P1 RS-422/485 NPort IA5150/5250 Series User’s Manual Getting Started Panel Layout NPort IA5150 Series Top View Front View Bottom View PWR1 PWR2 1 RDY V2+ P1 V2 FX LED Indicators V1+ V1 Reset Reset Fiber optic RS-422/485 Ethernet IA RS-232 Dual power input 5150-M-SC and relay output NPort IA 5250 Top View Front View Bottom View PWR1 PWR2 1 RDY V2+ P1 V2 P2 LED Indicators V1+ V1 Reset Ethernet 1 Ethernet 2 Reset RS-232/422/485 Copper Ethernet IA Dual power input
Inhaltszusammenfassung zur Seite Nr. 11
NPort IA5150/5250 Series User’s Manual Getting Started Wiring Requirements ATTENTION Safety First! Be sure to disconnect the power cord before installing and/or wiring your NPort IA5150/5250 Series. Wiring Caution! Calculate the maximum possible current in each power wire and common wire. Observe all electrical codes dictating the maximum current allowable for each wire size. If the current goes above the maximum ratings, the wiring could overheat, causing serious damage to your equip
Inhaltszusammenfassung zur Seite Nr. 12
NPort IA5150/5250 Series User’s Manual Getting Started SG: The Shielded Ground (sometimes called Protected Ground) contact is the left most contact of the 7-pin power terminal block connector when viewed from the angle shown here. Connect the SG wire to an appropriate grounded metal surface. Connecting to the Network Connect one end of the Ethernet cable to NPort IA5150/5250’s 10/100M Ethernet port and the other end of the cable to the Ethernet network. If the cable is properly connect
Inhaltszusammenfassung zur Seite Nr. 13
NPort IA5150/5250 Series User’s Manual Getting Started LED Indicators The top panels of all NPort IA5150/5250 device servers have four LED indicators, as described in the following table. LED Name LED Color LED Function PWR1, red Power is being supplied to power input PWR1, PWR2. PWR2 Steady on: Power is on and NPort IA is booting up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly, or a relay output occurred. When the above two conditions occur at
Inhaltszusammenfassung zur Seite Nr. 14
3 3 Chapter 3 Initial IP Address Configuration When setting up your NPort IA5150/5250 for the first time, the first thing you should do is configure the IP address. This chapter introduces the methods that can be used to configure the device server’s IP address. Select one of the initial IP Address configuration methods to configure NPort IA5150/5250’s IP Address. For more details about network settings, see the Network Settings section from Chapter 5, Web Console Configuration. The fo
Inhaltszusammenfassung zur Seite Nr. 15
NPort IA5150/5250 Series User’s Manual Initial IP Address Configuration Initializing NPort IA5150/5250’s IP Address 1. Determine whether your NPort IA5150/5250 needs to use a Static IP or Dynamic IP (either DHCP or BOOTP application). 2. If NPort IA5150/5250 is used in a Static IP environment, you can use NPort IA5150/5250 Administration Suite, ARP, Web Console, Telnet Console, or Serial Console to configure the new IP address. 3. If NPort IA5150/5250 is used in a Dynamic IP environment,
Inhaltszusammenfassung zur Seite Nr. 16
NPort IA5150/5250 Series User’s Manual Initial IP Address Configuration Take the following steps to use ARP to configure the IP address: 1. Obtain a valid IP address for your NPort IA5150/5250 from your network administrator. 2. Obtain NPort IA5150/5250’s MAC address from the label on its bottom panel. 3. Execute the ‘arp -s’ command from your computer’s MS-DOS prompt by typing: arp -s 192.168.200.100 00-90-E8-xx-xx-xx This is where 192.168.200.100 is the new IP address and 00-90-E8-xx-xx-
Inhaltszusammenfassung zur Seite Nr. 17
NPort IA5150/5250 Series User’s Manual Initial IP Address Configuration 4. Type 2 to select Network settings, and then press Enter. 5. Type 1 to select IP address and then press Enter. 6. Use the Backspace key to erase the current IP address, type in the new IP address, and then press Enter. 3-4
Inhaltszusammenfassung zur Seite Nr. 18
NPort IA5150/5250 Series User’s Manual Initial IP Address Configuration 7. Press any key to continue. 8. Type m and then press Enter to return to the main menu. 9. Type s and then press Enter to Save/Restart the system. 10. Type y and then press Enter to save the new IP address and restart NPort IA5150/5250. 3-5
Inhaltszusammenfassung zur Seite Nr. 19
NPort IA5150/5250 Series User’s Manual Initial IP Address Configuration Serial Console (19200, n, 8, 1) You may use the RS-232 console port to set up the IP address for NPort IA5150/5250. We suggest using PComm Terminal Emulator, which is available free of charge as part of the PComm Lite program suite, to carry out the installation procedure, although other similar utilities may also be used. ATTENTION The Serial Console is an RS-232 port (port 1 for NPort IA5250). Before you start
Inhaltszusammenfassung zur Seite Nr. 20
NPort IA5150/5250 Series User’s Manual Initial IP Address Configuration 6. Press the “ ` ” key continuously and then power on the NPort IA5150/5250. 7. NPort IA5150/5250 will automatically switch from data mode to console mode as it receives a continuous string of “ ` ”. 8. Input the password when prompted. Note that this page will only appear when the NPort IA5150/5250 has been set up for password protection. 9. Start configuring the IP address under Network Settings. Refer to step 4
