Inhaltszusammenfassung zur Seite Nr. 1
SP2515 SERIES
EtherFast 100Mbps Fiber-Optic Adapter
User’s Guide
Inhaltszusammenfassung zur Seite Nr. 2
FCC Statement This device compiles with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning! This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro
Inhaltszusammenfassung zur Seite Nr. 3
1. Introduction Congratulations on the purchasing of your new SP2515 series 100Mbps Fast Ethernet Fiber adapter. This document describes how to install and use the Fiber Ethernet Adapter. This Fiber Adapter allows options of different fiber connections, such as connector types and segment distance. To get the most out of this manual, you should have an understanding of Ethernet networking concepts. 1.1 F 1.1 F 1.1 F 1.1 Fe e e eatures atures atures atures Micronet SP2515 ser
Inhaltszusammenfassung zur Seite Nr. 4
2. Installation This section describes how to install the adapter. For connecting to the network, you must have the following: 1. Network adapter card installed to your computer. 2. Cabling (compatible with network topology) 3. Software for the adapter card contains both configuration utilities and drivers 2.1 U 2.1 Un npack and Inspect pack and Inspect 2.1 U 2.1 Un npack and Inspect pack and Inspect Caution: Under ordinary circumstances, this adapter card will not be affe
Inhaltszusammenfassung zur Seite Nr. 5
5. Carefully insert the Fiber Adapter into the chosen slot and press firmly with proper push to ensure it is fully seated in the slot. 6. Secure the Fiber Adapter with the screw you saved in step 4. 7. Replace the PC cover. 8. Proceed to “Connecting to Your Network” section. 2.3 2.3 2.3 2.3 C C C Co o o on n n nn n n ne e e ecti cti cti ctin n n ng to g to g to g to Y Y Y Yo o o our ur ur Ne ur Ne Ne Netwo two two twor rr rk k k k This section describes how to connect the Fi
Inhaltszusammenfassung zur Seite Nr. 6
2. 2. 2. 2.6 6 T 6 6 Te Te Te es s s stttt P P P Pr rr ro o o og g g gr rr ra a a am m m m This test program verifies configuration of the adapter and assists the isolation of any faults in operation. Test procedure are optional, and will only be useful in the unusual event that there is a fault, such as an interrupt number conflict among your computer’s add on cards, If your installation provides normal operation, you do not need these test procedures. At your DOS prompt
Inhaltszusammenfassung zur Seite Nr. 7
test reminds you that the connection link might be fail, either the cable is not connected or the cable link fails. For the test, it is necessary to connect your computer with its supporting hub or another computer. This is a "Ping-Pong" test. This test cannot be completed except two computers on the LAN for sending or receiving the test packets between computers. For the test Ethernet Address Ethernet
Inhaltszusammenfassung zur Seite Nr. 8
Quick Installation Guide Please take the following steps for driver installation. M Miic crros osoft oft W Wiin nd dows ows 9 95 5/ /W Wiin nd dows ows 9 98 8 M Miic crros osoft oft W Wiin nd dows ows 9 95 5/ /W Wiin nd dows ows 9 98 8 1. Turn off the computer. 2. Insert the adapter into the available PCI slot. 3. Restart the computer. 4. After Microsoft Windows reboot, the PCI Ethernet Controller will be found. 5. The system will prompt for driver installation. 6. Insert
Inhaltszusammenfassung zur Seite Nr. 9
M Miicr cro os so offt W t Wiind ndo ow ws 2000 s 2000 M Miicr cro os so offt W t Wiind ndo ow ws 2000 s 2000 1. Turn off the computer. 2. Insert the adapter into the available PCI slot. 3. Restart the computer. 4. After Microsoft Windows reboot, the 100Mbps Fast Ethernet Adapter will be found and the system will assign the default network driver to the adapter. 5. Select “Control Panel” from “Start” menu bar 6. Select “Network and Dial-Up Connection” folder and click “Local Area C
Inhaltszusammenfassung zur Seite Nr. 10
No Note te No Note te
