Inhaltszusammenfassung zur Seite Nr. 1
Quick Start Guide
™
EasyLAN 10i2
Ethernet Adapter
Inhaltszusammenfassung zur Seite Nr. 2
Intermec Technologies Corporation Corporate Headquarters 6001 36th Ave. W. Everett, WA 98203 U.S.A. www.intermec.com The information contained herein is proprietary and is provided solely for the purpose of allowing customers to operate and service Intermec-manufactured equipment and is not to be released, reproduced, or used for any other purpose without written permission of Intermec. Information and specifications contained in this document are subject to change without prior no
Inhaltszusammenfassung zur Seite Nr. 3
Contents Introducing the EasyLAN 10i2 Adapter......................5 Physical Description ...................................................6 Out of the Box ...........................................................8 Installing the EasyLAN 10i2 Adapter..........................8 Connecting the EasyLAN 10i2 Adapter to Your Network..........................................8 Printing a Test Label ..................................10 Downloading the IP Address ......................10 M
Inhaltszusammenfassung zur Seite Nr. 4
blank iv EasyLAN 10i2 Ethernet Adapter Quick Start Guide
Inhaltszusammenfassung zur Seite Nr. 5
Introducing the EasyLAN 10i2 Adapter ™ The external EasyLAN 10i2 Ethernet adapter (P/N 072885) and the internal EasyLAN 10i2 Ethernet adapters (P/N 072894 and P/N 072884) let you share your available printer resources with everyone connected to your Ethernet network. Throughout the guide, “EasyLAN 10i2 adapter” is used to refer to both the internal and external adapter unless otherwise specified. You can only connect the external EasyLAN 10i2 adapter to these printers: EasyCoder 91
Inhaltszusammenfassung zur Seite Nr. 6
Note: If you are using the internal EasyLAN 10i2 adapter, you cannot use the parallel port. The EasyLAN 10i2 adapter uses a 10BaseT connection, which has a network speed of 10 Mbps. Physical Description LED Test button 10BaseT connector EL10i011.eps Internal EasyLAN 10i2 Adapter Parallel port connector LED Test button 10BaseT connector External power supply connector EL10i010.eps External EasyLAN 10i2 Adapter 6 EasyLAN 10i2 Ethernet Adapter Quick Start Guide O I
Inhaltszusammenfassung zur Seite Nr. 7
Connectors, LED, and Button Table Part Description 10BaseT connector Connects the EasyLAN 10i2 adapter to a 10 Mbps Ethernet network via a 10BaseT cable. External power supply Connects the external EasyLAN connector (external 10i2 adapter to a power source via adapter only) a power supply. Parallel port connector Provides the external EasyLAN (external adapter only) 10i2 adapter with a single high-speed parallel port that can connect directly, without the need of cabling, to an Int
Inhaltszusammenfassung zur Seite Nr. 8
Out of the Box Your printer with the EasyLAN 10i2 adapter installed comes with the following: ™ PrinterCompanion CD-ROM, which includes the EasyLAN 10i2 Ethernet Adapter User’s Manual (P/N 072889) in PDF format and the Intermec print monitor This guide and Important EasyLAN 10i2 Information! Installing the EasyLAN 10i2 Adapter Before you install the EasyLAN 10i2 adapter, make sure that you have the appropriate Ethernet cable and power cable. Also make sure that you have loaded m
Inhaltszusammenfassung zur Seite Nr. 9
2 Turn off the printer. 3 Plug the parallel port connector on the adapter into the parallel port on the printer. Parallel port 10BaseT cable Parallel port connector 10BaseT connector EL10i009.eps 4 Connect one end of a 10BaseT cable to the 10BaseT connector on the adapter. 5 Connect the other end of the 10BaseT cable to an Ethernet port for your network. 6 If necessary, plug in the external power supply. 10BaseT cable External power supply connector External EL10i008.eps power su
Inhaltszusammenfassung zur Seite Nr. 10
7 Turn on the printer. The LED on the adapter flashes and then turns off. When you turn on the printer with the EasyLAN 10i2 adapter, the adapter runs through a set of power-up diagnostics for a few seconds. If the adapter is operating properly, the LED blinks momentarily and then turns off. The LED blinks whenever there is networking activity. If you have a DHCP (Dynamic Host Configuration Protocol) server on your network, the EasyLAN 10i2 adapter receives its TCP/IP settings, includ
Inhaltszusammenfassung zur Seite Nr. 11
To download the IP address from a Windows-based PC ® 1 Start a DOS window. 2 Type the following command: arp -s nnn.nnn.nnn.nnn nn-nn-nn-nn-nn-nn ping nnn.nnn.nnn.nnn arp -d nnn.nnn.nnn.nnn where: nnn.nnn.nnn.nnn is the IP address for the EasyLAN 10i2 adapter. nn-nn-nn-nn-nn-nn is the MAC address for the EasyLAN 10i2 adapter. To download the IP address from a UNIX host Type the following command: arp -s host_name nn:nn:nn:nn:nn:nn temp ping host_name where: host_
Inhaltszusammenfassung zur Seite Nr. 12
Managing and Configuring the EasyLAN 10i2 Adapter If you want to manage or configure more advanced parameters on the EasyLAN 10i2 adapter, you can use the following tool: Web browser interface. You can access the web browser interface by typing the IP address for the EasyLAN 10i2 in either Internet Explorer or Netscape. For help, see the EasyLAN 10i2 Ethernet Adapter User’s Manual. You can also use the Intermec print monitor to create a network port for the Ethernet link on a Windo
