Bedienungsanleitung IBM Network Device 9000s

Inhaltszusammenfassung zur Seite Nr. 1

[ Quick Start Guide ]
FIBRE CHANNEL SWITCH INSTALLATION
z
®
SANbox 9000 Series
®
for Windows Operating Systems
QUICK START GUIDE

Inhaltszusammenfassung zur Seite Nr. 2

Purchasers of OEM products should consult with the OEM for support. Support Headquarters QLogic Corporation 12984 Valley View Road Eden Prairie, Minnesota 55344-3657 USA QLogic Web Site www.qlogic.com Technical Support Web Site support.qlogic.com Technical Support Email support@qlogic.com Technical Training Email tech.training@qlogic.com North American Region Email support@qlogic.com Phone +1-952-932-4040 Fax +1 952-974-4910 Europe, Middle East, and Africa Region Email emeasupport@qlogic.com Pho

Inhaltszusammenfassung zur Seite Nr. 3

Quick Start Guide Installation Instructions ® Congratulations on your purchase of the SANbox 9000 Series Fibre Channel Switch. This guide describes the steps to install and activate your new switch using a Windows® workstation. For advanced options and instructions (including ® ® ® Solaris , Linux , and Mac OS X installations), refer to the SANbox 9000 Series Stackable Chassis Switch Installation Guide on the product CD. NOTE: Do not apply power to the switch until instructed in Step 4. Step

Inhaltszusammenfassung zur Seite Nr. 4

Step 4. Apply Power to the Switch The maximum current requirements are 10 amps at 100 VAC or 4.2 amps at 240 VAC. ❑ Attach the AC power cords to the Power Supply blades CHASSIS and wall outlets or power strips. Secure the strain CHASSIS relief bales to the plugs. Place the On/Off switches in GOOD LED FAULT LED the On position. ❑ The switch runs its self tests and begins normal operation – this may take a few minutes. Observe the Maintenance Panel and verify that the CPU0 blade Heartbeat LE

Inhaltszusammenfassung zur Seite Nr. 5

Step 6. Connect the Workstation to the Switch ❑ Connect the CPU0 blade Ethernet port directly to the workstation using an Ethernet cable, or indirectly through a switch or hub. The Ethernet port automatically discovers straight and cross-over cables. You must have a live Ethernet connection when the workstation powers up. NOTE: The Maintenance Panel Ethernet ports on the front of the switch are disabled and should not be used for the initial installation. You can enable the Maintenance Panel

Inhaltszusammenfassung zur Seite Nr. 6

Step 9. Run the Configuration Wizard ❑ Double-click the Enterprise Fabric Suite 2007 shortcut, or select Enterprise Fabric Suite 2007 from Start menu, depending on how you installed it. ❑ The Configuration Wizard tool auto-detects and configures the switch based on selected options and recommended settings. Follow the instructions to set network parameters and the password. The default user name is admin; the default password is password. NOTE: If you are using an Ethernet switch and the auto

Inhaltszusammenfassung zur Seite Nr. 7

© 2007 QLogic Corporation. QLogic, the QLogic logo, SANbox, and Enterprise Fabric Suite 2007 are trademarks or registered trademarks of QLogic Corporation. Microsoft , Windows, and Internet Explorer are registered trademarks of the Microsoft Corporation. MacOS X is a registered trademark of Apple Computer, Inc. Linux is a registered trademark of Linus Torvalds. Mozilla and Firefox are trademarks or registered trademarks of the Mozilla Foundation. Netscape Navigator is a registered trademarks of

Inhaltszusammenfassung zur Seite Nr. 8

*50688-03 A* QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com 50688-03 A J