Inhaltszusammenfassung zur Seite Nr. 1
GS-SR125EDL
Rack Mount Server
User’ s Manual
TM
Dual Xeon Processor Motherboard / Server Solution
Rev. 1001
25A08-05EDL-C00
Inhaltszusammenfassung zur Seite Nr. 2
GS-SR125EDL Rack mount Serv er Table of Content Safety, Care and Regulatory Information ........................................... 4 Introduction ..................................................................................... 8 Contents Packages ......................................................................... 8 WARNING! ...................................................................................... 8 Chapter 1 Features Summary ..............................................
Inhaltszusammenfassung zur Seite Nr. 3
Table of Content Cache Memory ......................................................................................... 41 I/O Dev ice Configuration ............................................................................. 43 Console Redirection ................................................................................... 45 Security ..................................................................................................................48 Boot ................................
Inhaltszusammenfassung zur Seite Nr. 4
GS-SR125EDL Rack mount Serv er Safety, Care and Regulatory Information L Important safety information Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. * The product should be operated only from the type of power source indicated on the rating label. * If your computer has a voltage selector switch, make sure that the switch is in the proper position for your area. The volta
Inhaltszusammenfassung zur Seite Nr. 5
Safety Information * To reduce the risk of fire, use only No. 26 AWG or larger telecommunications line cord. * Do not plug a modem or telephone cable into the network interface controller (NIC) receptacle. * Disconnect the modem cable before opening a product enclosure, touching or installing internal components, or touching an uninsulated modem cable or jack. * Do not use a telephone line to report a gas leak while you are in the vicinity of the leak. L Federal Communications Commission (FCC) S
Inhaltszusammenfassung zur Seite Nr. 6
GS-SR125EDL Rack mount Serv er Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect proper operation of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. The FCC prohibits this equipment to be connected to party lines or coin-telephone service. The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec.
Inhaltszusammenfassung zur Seite Nr. 7
Safety Information NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the sum of the Load Numbers of all the devices does not exceed 100. / for European users only / CAUTION v Danger of explosion if battery is incorrectly replaced. v Replace only with th
Inhaltszusammenfassung zur Seite Nr. 8
GS-SR125EDL Rack mount Serv er Introduction Welcome to Gigabyte GS -SR125EDL Rack mount Server System Installation Guide. The guide provides instructions for configuration hardware for the GS-SR125EDL your system. This installation guide will assiste you in installing all the essential components for the sever system. For your protection, please read and undertand all of the safety and operating instructions regarding your Gigabyte Server and retain for future reference. The procedures in this g
Inhaltszusammenfassung zur Seite Nr. 9
Feature Summary Chapter 1 Features Summary Motherboard GA-8EGPDRE ® TM Processor Supported Dual socket 604 for Intel FC-PGA Xeon processor suopprts up to 3.06GB ® Intel Xeon 533MHz FSB Chipset ServerWorks CMIC-SL Northbridge ServerWorks CIOB-E Dual Giagbit LAN and PCI-X Bridge ServerWorks CSB6 Southbridge System Memory: Memory Capacity 4 x 184-pin DDR266 DIMM Sockets Supports 4GB Maximum Capacity Memory Type DDR266; Registered DDR DIMM Size 64MB, 128MB, 256MB, 512MB, 1GB Me
Inhaltszusammenfassung zur Seite Nr. 10
GS-SR125EDL Rack mount Serv er Integrated Super I/O: Serial Ports 1 x Serial Port COM1 (Rear I/O-Shield) 1 x Serial Port COM2 (Front I/O Shield) Both Support Console Redirection Keyboard/Mouse 1 x PS/2 Keyboard Port (Rear I/O-Shield) 1 x PS/2 Mouse Port (Rear I/O-Shield) USB: 1.1 2 x USB ports (Rear I/O-Shield) 2 x USB Port (Front Panel) System BIOS: ® BIOS Type Phoenix BIOS, Multi-boot BBS 1.0 Compliant4Mb Flash Memory Special Features ACPI 1.1, DMI, WFM, PXE, Plug and Play,
Inhaltszusammenfassung zur Seite Nr. 11
Hardw are Installation Process Chapter 2 System Hardware Installation Please observe the safety information in chapter ¡ § Important Safety Information¡ ¨ Do not expose the server to extreme environmental conditions. Protect it from dust, humidity, and heat. Step 2-1: Chassis Removal Step 1 Push down the two buttons located at two sides of the chassis. Step 2 And slide toward to remove the top cover. After removing the top cover, you can install CPU and other essential components. Step 1 Step 2
Inhaltszusammenfassung zur Seite Nr. 12
GS-SR125EDL Rack mount Serv er Step 3 Step 2-3: Heat Sink Installation Step 1 To install the heat sink, just simply put it on the retention module. Step 1 Step 2-4: Memory Installation Step 1 The DIMM slot has a notch, the DIMM memory module only fit in one direction. Step 2 Align the memory notch to the module and push the memory into the DIMM socket. Step 1 Step 2 Notch 12
Inhaltszusammenfassung zur Seite Nr. 13
Hardw are Installation Process Step 2-5: PCI Expansion Card Installation PCI Slot 2 is not compliance with this model. GS-SR125EDL provides expansion riser slots for two peripheral cards, 100/133MHz , one full-height/ one half-length. To install the peripheral, please go through the following steps. Step 1 Remove the screws on the riser bracket. Step 2 Detach the riser bracket with both hands. Step 3 Installing the PCI Riser card. To install the riser card, just simply push it into the module. S
Inhaltszusammenfassung zur Seite Nr. 14
GS-SR125EDL Rack mount Serv er Step 5 Step 2-6: Hard Disk Drive Installation Step 1 Pull the hard disk drive tray handle and remove the tray from the chassis. Step 2 Insert the hard disk drive into the tray. Step 3 Secure each hard disk drive with 4 screws. Step 4 After securing the hard disk drive with the screws, hold the hard drive handle at open position, place the tray into chassis and push the hard disk drive tray handle to the locked position. Step 1 Step 2 Step 4 Step 3 14
Inhaltszusammenfassung zur Seite Nr. 15
Hardw are Installation Process Step 2-7: FAN Duct Installation Step 1 Place the fan duct on the top of heat sinks. Step 2 Fasten the fan duct with two screws. Step1 & 2 Screw Screw Step 2-8: Reinstall Top Cover Step 1 Gently apply force to the indentures with your thumbs and push toward the chassis (See the arrow direction) to the lock position. Step 1 15
Inhaltszusammenfassung zur Seite Nr. 16
GS-SR125EDL Rack mount Serv er Chapter 3 Appearance of GS-SR125EDL 3-1: Front View of GS-SR125EDL v w x u IDE HDD u USB Connectors v System LED w CD-ROM Disk x 16
Inhaltszusammenfassung zur Seite Nr. 17
System Appearance 3-2: Rear View of GS-SR125EDL v w x z y u | { PS/2 Keyboard & Mouse Connector u Low Profile v Full-Height / Full- Length w LAN 1 / 2 Ports x VGA Port y COM Port z USB Connectors { Power Connector | 17
Inhaltszusammenfassung zur Seite Nr. 18
GS-SR125EDL Rack mount Serv er 3-3: IDE Backplane Layout and Description S L T N J Q F E K M H O P B G C R A D I X U W V A ,C ,D G F , H I K , J R M , L S O, N T P U Q V E W B X 18
Inhaltszusammenfassung zur Seite Nr. 19
LED Description 3-4: Switch and LED Indicators Description Acting Color Status Power LED On Green Pow er On On Amber Pow er cable is plugged in Blink Green System stands by Off N/A No pow er SYS LED On Amber System is ready but degraded: some CPU Fault, DIMM Killed Critical Pow erModules Failure, Critical FANs Failure, Voltage (Pow er Supply), critical Temperature and Voltage Off N/A Normal temperature and voltage LAN LED On Green LAN online Off N/A LAN offline Blink Green LAN active ID(Serv
Inhaltszusammenfassung zur Seite Nr. 20
GS-SR125EDL Rack mount Serv er 3-5: HDD LED Indicators Description HDD LED 1 HDD LED 2 Acting Color Status HDD LED 1 Off N/A HDD LED 1 On Green HDD LED 2 Off N/A HDD LED 2 Blink Green 20
