Inhaltszusammenfassung zur Seite Nr. 1
UB-E02
Technical Reference
Guide
10Base-T/100Base-TX
Ethernet Interface board
English
EPSON
404999001
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
UB-E02 Technical Reference Guide CAUTIONS ❏ This document shall apply only to the product(s) identified herein. ❏ No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. ❏ The contents of this document are subject to change without notice. Please contact us for the latest information. ❏ While every precauti
Inhaltszusammenfassung zur Seite Nr. 4
Revision Information Revision Page Altered Items and Contents Rev. A ii Rev. A
Inhaltszusammenfassung zur Seite Nr. 5
UB-E02 Technical Reference Guide About This Guide This guide is intended to provide all information necessary for system planning, design, installation and application of the UB-E02 for designers and developers of POS systems. Contents of the Guide The configuration of the guide is as follows: Chapter 1, “System Preparation” Supported operating system, network protocols, TM printers, and other limitations. Chapter 2, “Installation” Gives information on how to install and use the UB-E02. Cha
Inhaltszusammenfassung zur Seite Nr. 6
EMC and Safety Standards Applied Product Name: UB-E02 Model Name: M155B The following standards are applied only to the interface boards that are so labeled. (EMC is tested using the EPSON power supplies and TM series printers.) Europe: CE marking North America: EMI: FCC/ICES-003 Class A Japan: EMC: VCCI Class A Oceania: EMC: AS/NZS 3548, CISPR22 Class B WARNING The connection of a non-shielded interface cable to this board will invalidate the EMC standards of this device. You are cautioned t
Inhaltszusammenfassung zur Seite Nr. 7
UB-E02 Technical Reference Guide CAUTION: Connecting an outdoor overhead LAN cable directly to your product Connecting an outdoor overhead LAN cable directly to your product may lead to lightning damage. If you need to connect such a cable to your product, the cable must be protected against an electrical surge between the cable and your product. You should avoid connecting your product to a non-surge protected outdoor overhead LAN cable. GEREÄUSCHPEGEL Gemäß der Dritten Verordnung zum Gerät
Inhaltszusammenfassung zur Seite Nr. 8
Safety Precautions This section presents important information to ensure safe and effective use of this product. Please read this section carefully and store it in an accessible location. CAUTION: Be careful to avoid dropping conductive objects such as paper clips on the circuit ❏ board, as they could short circuit connections and cause damage from excessive current. ❏ This product should only be connected to the devices specified in this guide. Connecting other devices could cause damage,
Inhaltszusammenfassung zur Seite Nr. 9
UB-E02 Technical Reference Guide Introduction ® The UB-E02 is the 10Base-T/100Base-TX Ethernet interface board designed for the EPSON TM printers. The board lets you connect your EPSON printer directly to your network and use it as a kitchen printer. Operating Environments Supported Operating Systems ® ® ® ® ❏ Microsoft Windows 95, Windows 98 Second Edition, Windows 2000 Professional, ® and Windows XP Professional ® ❏ Windows NT 4.0 Supported Protocols ❏ TCP/IP Environments for Setup Utility
Inhaltszusammenfassung zur Seite Nr. 10
Supported TM Printers The following printers can use the UB-E02. (The TM-J8000, TM-T285, and RP-U420 cannot use the UB-E02. For new models, please ask your dealer.) ❏ TM-U200 Series ❏ TM-U210 Series ❏ TM-U230 ❏ TM-U325 ❏ TM-U590 ❏ TM-U675 ❏ TM-T88/T88II/T88III ❏ TM-T90 ❏ TM-H5000/H5000II ❏ TM-H6000/H6000II ❏ TM-J2000/J2100 ❏ TM-J7000/J7100 ❏ TM-J7500/J7600 ❏ TM-L90 viii Rev. A
Inhaltszusammenfassung zur Seite Nr. 11
UB-E02 Technical Reference Guide How to Use this Guide Installation Overview Be sure to read Chapter 1, “System Preparation,” before using the product. Perform the following steps to install and configure the UB-E02. See the indicated chapters for detailed information. 1. Install the UB-E02 in your printer. See Chapter 2. 2. Install the TCP/IP protocol in your operating system, if necessary. See Chapter 5. 3. Set the functions of the UB-E02. See Chapter 5. 4. To set the functions of the UB-E02
Inhaltszusammenfassung zur Seite Nr. 12
Contents Chapter 1 System Preparation Supported Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Supported Network Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Supported TM Printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Other Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 13
UB-E02 Technical Reference Guide Chapter 5 Specifications Printer Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Line Display Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Overview . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 14
xii Contents Rev. A
Inhaltszusammenfassung zur Seite Nr. 15
UB-E02 Technical Reference Guide Chapter 1 System Preparation 1.1 Supported Operating Systems ❏ Microsoft Windows 95, Windows 98 Second Edition, Windows 2000 Professional, and Windows XP Professional ❏ Windows NT 4.0 1.2 Supported Network Protocols ❏ LPR ❏ Socket printing (port 9100 for OPOS) 1.3 Supported TM Printers The following printers can use the UB-E02. ❏ TM-U200 Series ❏ TM-U210 Series ❏ TM-U220 Series ❏ TM-U230 ❏ TM-U325 ❏ TM-U590 ❏ TM-U675 ❏ TM-T88/T88II/T88III ❏ TM-T90 ❏ TM
Inhaltszusammenfassung zur Seite Nr. 16
The following printers cannot use the UB-E02. ❏ TM-J8000, TM-T285, RP-U420 1.4 Other Limitations Be sure to note the following: ❏ When the UB-E02 is installed, the display module connector (DM-D) of the TM printer cannot be used. CAUTION: Do not connect the Ethernet connector cable to the display module connector (DM-D) or the drawer kick-out connector. 1-2 System Preparation Rev. A
Inhaltszusammenfassung zur Seite Nr. 17
UB-E02 Technical Reference Guide Chapter 2 Installation 2.1 Installation Precautions WARNING ❏ Before installing, disconnect the Power Unit from the TM Printer (as well as turning the power switch off). Even when the power switch is off, voltage is still present at some points on the circuit board. Changing components while the Power Unit is connected can cause damage to the UB-E02 and the printer. ❏ A grounded wrist strap should be worn during installation, to avoid damage from static ele
Inhaltszusammenfassung zur Seite Nr. 18
2.2 Unpacking ❏ UB-E02 ❏ UB-E02 User’s Manual 2.3 Part Names Power supply connector of the printer LED (green) Drawer kick-out 10BASE-T/100BASE-TX LED (yellow) Switch connector of the printer Ethernet interface connector Note: This photograph shows the TM-T88III printer with the UB-E02 installed. 2.4 Functions The switch and LEDs of the UB-E02 provide you with important information on operation and status of the UB-E02. 2.4.1 Switch Type: Non-locking push switch You can do the following
Inhaltszusammenfassung zur Seite Nr. 19
UB-E02 Technical Reference Guide 2.5 UB-E02 Installation CAUTION: Before installing the UB-E02, be sure to set the DIP switches or Memory switches as shown in the table below. For other models, please ask your dealer. Model Setting TM-U200 Series DIP SW 2-8: ON TM-U210 Series DIP SW 2-8: ON TM-U220 Series (STD) *1 DIP SW2-8: ON TM-U220 Series (US) *1 DIP SW2-4: ON TM-U230 Series DIP SW 2-4: ON TM-U325 Series DIP SW 2-8: ON TM-U590 Series DIP SW 2-8: ON TM-U675 Series DIP SW 2-8: ON TM-T88/T8
Inhaltszusammenfassung zur Seite Nr. 20
remove screw remove screw 3. Tighten the screws. If you have removed an interface circuit board that was already installed, fix the UB-E02 using the removed screws. 4. Plug the twist pair cable into the 10BASE-T/100BASE-TX Ethernet connector of the UB-E02 until it clicks. CAUTION: Be sure not to connect a telephone line, display module connector, or drawer kick-out connector cable to the 10BASE-T/100BASE-TX Ethernet connector of the UB-E02. The display module connector on the TM printer canno
