Inhaltszusammenfassung zur Seite Nr. 1
User’s Manual
RGB 500/Dual, RGB 508,
RGB 560/Dual, RGB 568
Architectural Series Universal Interfaces with Audio and ADSP™
Extron Electronics, Europe Extron Electronics, Asia Extron Electronics Information 68-455-02
Extron Electronics, USA
1230 South Lewis Street, Anaheim, CA 92805 Beeldschermweg 6C, 3821 AH Amersfoort 135 Joo Seng Rd. #04-01, PM Industrial Bldg. ExtronWEB™: www.extron.com
™ Printed in the USA
800.633.9876 714.491.1500 FAX 714.491.1517 +31.33.453.4040 FAX +31.33.453.4050 +6
Inhaltszusammenfassung zur Seite Nr. 2
Precautions Safety Instructions • English Warning Power sources This equipment should be operated only from the power source This symbol is intended to alert the user of important FCC Class A Notice indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor. The third (grounding) pin is in the literature provided with the equipment. Note: This equipment has been tested and foun
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About this Manual ................................................................ 1-2 About the RGB 500 Series Interfaces .......................... 1-2 Features ...................................................................................... 1-2 RGB 500 Series features ........................................................1-2 RGB 500, RGB 500 Dual, and RGB 508 feature .............
Inhaltszusammenfassung zur Seite Nr. 4
Table of Contents, cont’d RGB 508 and RGB 568 Faceplates .................................. C-4 RGB 500 Series Appendix D Accessories and Part Numbers........... D-1 Interfaces .................................................................................. D-2 Power Supply .......................................................................... D-3 Optional Adapter Plates ................................................... D-3 Single Type Connector Architectural Adapter Plates ..........
Inhaltszusammenfassung zur Seite Nr. 5
Introduction Introduction, cont’d Sync polarity adjustment — Horizontal and vertical sync About this Manual output can either follow input sync polarity, or outgoing This manual contains information about the Extron RGB 500 sync can be forced to negative via jumper settings. architectural series universal interfaces (RGB 500, RGB 500 Dual, Vertical sync pulse width adjustment — Vertical sync pulse RGB 508, RGB 560, RGB 560 Dual, and RGB 568) and on how to width can be adjusted via jumper setti
Inhaltszusammenfassung zur Seite Nr. 6
Introduction, cont’d Local monitor pins — These DIP switches are used for routing RGB 500 Series local monitor signals for Macintosh 13” monitors and all other Mac/VGA-type monitors. Chapter Two 2 Installation and Operation Installing the RGB 500 Series Interfaces Installation and Setup Overview Installation and Operation Instructions 1-4 RGB 500 Series Introduction
Inhaltszusammenfassung zur Seite Nr. 7
Installation and Operation Installation and Operation, cont’d Installing the RGB 500 Series Interfaces 11 Temporarily disconnect the computer video and audio input cables and (for RGB 560 and RGB 568 models) the The Extron RGB 500 Series interfaces consist of a faceplate, an local monitor output cable from the front panel of the interface (or interfaces) in a metal enclosure, and wall mounting interface. brackets. The RGB 508 and RGB 568 series interfaces may also include optional connector ada
Inhaltszusammenfassung zur Seite Nr. 8
1 2 34 12 3 4 Installation and Operation, cont’d injury to yourself or the cables during installation. 4. Insert the bracket back into the hole. 5. Use four ½” (1.3 cm) long, #6 flat headed wood screws Installing the mounting bracket with clips (provided) or self-tapping sheet metal screws to fasten the 1. Place 1¼” (3.18 cm) long or ¾“ (1.9 cm), #6-32 machine bracket directly onto wood or metal, respectively. Hand screws (provided) through the holes in each corner of the tighten the screws.
Inhaltszusammenfassung zur Seite Nr. 9
Installation and Operation, cont’d Bottom panel features 2 Sync polarity jumper switch — This jumper switch adjusts the NOTE It is not important which wire output sync polarity. Horizontal and vertical Negative Follow (positive or negative) connects sync output can either follow input sync to which outer pole of the 3-pole captive screw power connector. polarity, or be forced to negative. You will • The center pole is not used. 1 2 3 4 AC or DC power may be used. need needlenosed pliers
Inhaltszusammenfassung zur Seite Nr. 10
Installation and Operation, cont’d 6 Blue (B) output connector — BNC female connector for blue Polarity is not important: the positive or negative wire video output. may be connected to either of the outer poles. 7 Green (G) output connector — BNC female connector for green Bottom panel DIP switches — These four DIP switches, 5 video output. numbered 1 to 4 from left to right, control the sync on green, serration pulse, DDSP and composite sync output options. Red (R) output connector — BNC femal
Inhaltszusammenfassung zur Seite Nr. 11
BUFFERED H. SHIFT LOCAL MONITOR AUTO POWER AUDIO INPUT ID PIN 11 CS PIN 9 ID PIN 4 RGB 568 WITH ADSP TM Installation and Operation, cont’d Use the right two pins to increase the output signal and add 1. Insert the adapter plate screws through the holes in the 100% of the maximum peaking to the signal for very long faceplate. Attach the adapter plates to the faceplate with cable runs. the provided captive washers and #4-40 nuts. Adapter Plate Red Adjustment (100% gain/peaking shown) Green Adju
Inhaltszusammenfassung zur Seite Nr. 12
Installation and Operation, cont’d Set this switch to 75 ohms if no local monitor is connected Setting front panel switches or if the picture is too bright or blooming (unterminated). Set the front panel switches before cabling and testing inputs. These examples will show 2-gang size interfaces, but they apply 5 Computer video input 9-pin D male connector to both 2- and 4-gang sizes and to the EC models. Front panel features — RGB 560 series, RGB 568 series Front panel features — RGB 500 serie
Inhaltszusammenfassung zur Seite Nr. 13
Installation and Operation, cont’d 1 & 2 — Local monitor pins — These are used for routing local Connecting input cables monitor signals for Macintosh 13” monitors and all other At this point the input cables should be connected so that the Mac/VGA-type monitors. display can be tested and any necessary changes to switch 1 = ON and settings can be made before the interface is installed into the 2 = OFF — For Macintosh 13” monitors, set DIP switch 1 wall or furniture. to On and 2 to Off for prope
Inhaltszusammenfassung zur Seite Nr. 14
BUFFERED H. SHIFT LOCAL MONITOR AUTO POWER AUDIO INPUT ID PIN 11 CS PIN 9 ID PIN 4 RGB 560 WITH ADSPTM Installation and Operation, cont’d Pre-installation testing/troubleshooting Mounting the interface to the mounting bracket Before completing the installation, test the system to make sure 1. Temporarily disconnect the computer video and audio that the connections and interface settings are correct. input cables and (for the RGB 560 series and RGB 568 series) the local monitor output cable from
Inhaltszusammenfassung zur Seite Nr. 15
Installation and Operation, cont’d Attaching the faceplate RGB 500 Series 1. Attach the faceplate to the interface(s) using two 3/8” (0.95 cm) long #4-40 machine screws (provided) per two- gang size (four screws total for the RGB 500 Dual, RGB 508, RGB 560 Dual and RGB 568). Use the illustration on the opposite page as a guide. 2. Insert the interface and attached cables into the opening in the wall or furniture, taking care not to damage the cables. 3. Attach the faceplate to the mounting bra
Inhaltszusammenfassung zur Seite Nr. 16
Specifications, cont’d Specifications Max. rise/fall time ....................... 3.5 nS Video Polarity Gain ................................................ Unity (0.70V p-p), (0.725V p-p) 50% peaking, (0.75V p-p) 100% peaking AKM models ....................... RGBHV ...................... Polarity follows input when RGBHV Bandwidth ..................................... 300 MHz (-3dB) is input and the sync polarity switch is set Video input to Off. Sync polarity Number/signal type ..........
Inhaltszusammenfassung zur Seite Nr. 17
Specifications, cont’d Impedance .................................... 50 ohms unbalanced, 100 ohms balanced RGB 500 Series RGB 500 Series Gain error ..................................... ±0.1dB channel to channel Maximum level (600 ohm) ......... > +14dBm, balanced at stated %THD+N General Power ............................................ 12 to 24VAC or VDC, 0.35 A, 5 watts, external (Order the power supply separately, part #70-055-01.) Temperature/humidity .............. Storage -40° to +158°
Inhaltszusammenfassung zur Seite Nr. 18
Rough-in Templates Rough-in Templates, cont’d RGB 500 and RGB 560 Rough-in Template Use this template as a guide for cutting the hole in the installation surface (wall or furniture). This diagram is for the interfaces with 2-gang size faceplates. It is shown at actual size. Template for the 2-gang mounting bracket The solid, outer line (4.50” H x 4.60” W) represents the outside edge of the wall mounting bracket. The dotted line indicates the recommended cut-out area (3.875” H x 3.80” W)
Inhaltszusammenfassung zur Seite Nr. 19
Rough-in Templates, cont’d RGB 500 Series Appendix C C Dimensions RGB 500 and RGB 560 Faceplates RGB 500 Dual and RGB 560 Dual Faceplates RGB 508 and RGB 568 Faceplates B-4 RGB 500 Series Rough-in Templates
Inhaltszusammenfassung zur Seite Nr. 20
Dimensions Dimensions, cont’d Dimensions of the RGB 500 Series faceplates are provided here RGB 500 Dual and RGB 560 Dual Faceplates for those who wish to make their own customized faceplates. The diagrams are shown at 70% of actual size. RGB 500 Dual faceplate dimensions All dimensions are given in inches. HAND SAND TO 0.06" RADIUS AROUND THE TOP OF THESE EDGES. RGB 500 and RGB 560 Faceplates RGB 500 faceplate dimensions HAND SAND TO 0.06" RADIUS AROUND THE TOP OF THESE EDGES. RGB 560 Dual f
