Inhaltszusammenfassung zur Seite Nr. 1
™
Nashville 1000
Operating Guide
Inhaltszusammenfassung zur Seite Nr. 2
Intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of electrical shock — DO NOT OPEN! CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
Inhaltszusammenfassung zur Seite Nr. 3
ª Nashville 1000 ª Congratulations on your purchase of the Peavey Nashville 1000. As the leader in steel guitar amplification, we are proud to combine innovation and tradition in this new model. Our digital amp provides the clean power you require and reduces the weight, while the enhanced tone circuitry eliminates the desire for unnecessary after-market modifications. We still offer a premium spring ¨ reverb, our famous Black Widow 1501-4SB speaker, a back-panel preamp output and power amp ª in
Inhaltszusammenfassung zur Seite Nr. 4
Step 10. To adjust the overall level, use the Master Gain control. Step 11. To adjust out any undesirable distortion, use the Pre Gain knob. Turning the knob counter- clockwise results in a decreased level, thus reducing the overdriven signal. Any external effects units can also cause the signal to overdrive. Step 12. You should be able to play at this time. Vary the Reverb and/or EQ knobs to get a feel for their effect on your tone. Most importantly....READ THE REST OF THIS MANUAL. The Nas
Inhaltszusammenfassung zur Seite Nr. 5
Post EQ Patch (8) Similar to the Pre EQ Patch(4), these jacks are post EQ. The same notes apply. The return level should still be monitored for its strength. In addition, the Post EQ Patch can be taken in and out of the signal path via the footswitch. Master Reverb (9) Adjusting this control clockwise will result in more reverb content in the output of the amp. The reverb can be defeated by rotating the control counterclockwise or via the footswitch. Master Gain (10) The Master Gain controls the
Inhaltszusammenfassung zur Seite Nr. 6
ª NASHVILLE 1000 SPECIFICATIONS: Pre EQ Patch Send: Power Amplifier Section: Load Impedance: 10 k Ohms or greater Rated Power and Load: Nominal Output Level: -14 dBV, 0.2 V RMS 300 W RMS into 4 Ohms (with DDT compression) 190 W RMS into 8 Ohms (with DDT compression) Pre EQ Patch Return: 2 Ohms operation not recommend Impedance: High Z, 220 k Ohms Designed Input Level: -14 dBV, 0.2 V RMS Frequency Response: (Switching jack provides send to return connection when not used.) +0,-3 dB, 20 Hz to 2
Inhaltszusammenfassung zur Seite Nr. 7
7 ª Nashville 1000 Block Diagram EQ Pre-EQ Effects Loop Input Send Return Send Switch Post-EQ Logic Effects Loop Return Low Mid Shift High Pres. Ft. Sw. Pre Line Gain Out Ft. Sw. Pwr Preamp Amp In Out Reverb 300W 4 Ohm Speaker Digital Level Master Switching Gain Power Amp
Inhaltszusammenfassung zur Seite Nr. 8
8 ª Nashville 1000 Recommended Tone Settings Clean Single Coil Guitar Steel: E9 Tuning Steel: C6 Tuning Lap Steel Fiddle *For CLEAN settings: the MASTER should be a higher setting than the PRE GAIN to avoid premature signal clipping.
Inhaltszusammenfassung zur Seite Nr. 9
NOTES 9
Inhaltszusammenfassung zur Seite Nr. 10
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. For example, near or in a bathtub, swimming pool, sink, wet basement, etc. 6. Clean only with a damp cloth. 7. Do not block any of the ventilation openings. Install in accordance with manufacturerÕs instructions. It
Inhaltszusammenfassung zur Seite Nr. 11
PEAVEY ELECTRONICS CORPORATION LIMITED WARRANTY Effective Date: July 1, 1998 What This Warranty Covers Your Peavey Warranty covers defects in material and workmanship in Peavey products purchased and serviced in the U.S.A. and Canada. What This Warranty Does Not Cover The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2) damage occurring during shipment; (3) damage caused by repair or service pe
Inhaltszusammenfassung zur Seite Nr. 12
Features and specifications subject to change without notice. Peavey Electronics Corporation ¥ 711 A Street ¥ Meridian, MS 39301 ¥ U.S.A. (601) 483-5365 ¥ Fax (601) 486-1678 ¥ www.peavey.com ©1999 Printed in U.S.A. 3/99 80304539
