Inhaltszusammenfassung zur Seite Nr. 1
Solid State Logic
||
S O U N D V I S I O N
SUPERANALOGUE
X-RACK
Super-Analogue™ Outboard
XR622 X-Rack Master Module User’s Guide
This documentation package contains the User’s Guide for your new X-Rack Master
module. Depending on the age of your X-Rack, these pages may already be present in
your X-Rack Owner’s Manual – please check to see if these pages match your Manual.
If they do not, these pages should be filed alongside it.
Please Note. The XR623 X-Rack Master module operates in conjunction
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
X-Rack Master Module F. The Master Module F.1 Introduction Used in conjunction with the XR623 X-Rack Line Return module, the XR622 X-Rack Master module provides a complete small scale mix and monitor system for studios seeking a compact solution for mixing and monitoring in the analogue domain. A single X-Rack can provide up to 28 line level inputs. Additional racks can be connected via the ‘MIX BUS LINK’ connector on the rear of the X-Rack unit, allowing additional inputs to be added to the sys
Inhaltszusammenfassung zur Seite Nr. 4
X-Rack Owner’s Manual 2 F.3.2 Monitor Section XR622 The Monitor Section enables the Mix and Record busses or a stereo external input to be monitored, the source to monitor being set by either the ‘MIX’, ‘REC’ or ‘EXT’ SEL switches either seperately or together, allowing great flexibility in recording and 0 3 montitoring signals. The ‘EXT’ input would normally be playback from the main 6 9 12 3 15 recorder or DAW. The selected monitor signals can be routed back to the Mix output 18 24 30 using t
Inhaltszusammenfassung zur Seite Nr. 5
X-Rack Master Module • Use the D-Pot to select ‘le’ (MIDI Remote Learn) and press SAVE to enable learn mode. • Operate any one of the ‘soft’ controls on the XR622 Master module. This will cause the LED of the selected control to flash (the ‘SEL’ LED will flash if either of the potentiomenters have been chosen). Assign a MIDI controller to the selected function by operating the required MIDI controller. Repeat the ‘operate – assign’ process for all required controls. • Press the D-Pot again to le
Inhaltszusammenfassung zur Seite Nr. 6
X-Rack Owner’s Manual F.4 Performance Specification The following page contains audio performance specification figures for the X-Rack Master module. No other Solid State Logic products are covered by this document and the performance of other Solid State Logic products can not be inferred from the data contained herein. F.4.1 Measurement Conditions For each set of figures on the following pages, the specific unit and test setup will be stated at the beginning of that section. Any changes to the
Inhaltszusammenfassung zur Seite Nr. 7
X-Rack Master Module F.5 Calibration Information The X-Rack Master module is factory calibrated and should only need calibration if a potentiometer or other component has been replaced or if it is suspected that there is a problem with calibration. In each of the following instructions it is assumed that the lid of the X-Rack has been removed and that power has been applied. It is also assumed that, unless otherwise specified, all switches are released and all front panel potentiometers are at u
Inhaltszusammenfassung zur Seite Nr. 8
X-Rack Owner’s Manual F.6 Connector Details Ins Rtn, Ext, Mon, Alt Mon Ins Snd, Mix, Rec, Fol Mon Location: Rear Panel Location: Rear Panel Conn’ Type: 25-pin ‘D’ Type Female Conn’ Type: 25-pin ‘D’ Type Female Pin Description Pin Description 1 Alt Monitor Out Right (+ve) 1 Follow Monitor Right (+ve) 14 Alt Monitor Out Right (–ve) 14 Follow Monitor Right (–ve) 2 0V 2 0V 15 Alt Monitor Out Left (+ve) 15 Follow Monitor Left (+ve) 3 Alt Monitor Out Left (–ve) 3 Follow Monitor Left (–ve) 16 0V 16 0V
Inhaltszusammenfassung zur Seite Nr. 9
X-Rack Master Module F.7 Physical Specification * Depth: 200mm / 7.9 inches including front panel knobs, excluding connectors 275mm / 10.9 inches including front panel knobs and connectors Height: 171mm / 6.75 inches Width: 35mm / 1.4 inches front/rear panels 49mm / 1.9 inches overall width (front and rear panels are offset) Weight: 260g / 9.5 ounces Boxed size: 190mm x 290mm x 70mm / 7.5" x 11.5" x 2.5" Boxed weight: 460g / 16.5 ounces * All values are approximate F.8 Environmental Specificatio
Inhaltszusammenfassung zur Seite Nr. 10
X-Rack Owner’s Manual Page F-8
