Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
APPLICATIONAND FEATURE LIST Features of theAMC model XOi TM * System for total 4 Zones * System with 8 Sources 4 Local / 4 Remote mixed Sources. * Only RJ45 & Speaker Wires used for installations from XOi main unit to all zones * Two ways AMC propriotary Digital Data Communication System between XOi main unit and keypads in all zones * Designed with cascade feature for keypad XK1 * Volume Control & Tone Control for each Zone * Four 38KHz and four 56KHz IR outputs on rear panel of XOi main unit *
Inhaltszusammenfassung zur Seite Nr. 4
REAR PANEL CONNECTIONS/FRONT PANEL CONTROLS 12 8 3457 6 9 10 11 Front Rear Doorbells1&2 Tel Lines1&2 AMC PDM1 (Phone-Doorbell-Mute Module) Zone 1 Zone 2 Zone 3 Zone 4 1. Local Source Inputs 1~4 7. 12VDC 2. IR Out - 38KHz 8. Keypads & Remote Sources 3. IR Out - 56KHz 9. Speaker Terminals 4. Mute 10. RS232 5. Link 11.AC input receptacle with Fuse 6. Status FRONT PANEL 1 2 1. Power Switch (Standby / Off) & 2.ZoneLED&4squareRecesses Blue LED 3
Inhaltszusammenfassung zur Seite Nr. 5
REAR PANEL CONNECTIONS 1. Local Source Inputs 1~4 3. IR Out - 56KHz Each of these stereo RCA inputs For cable and satellite boxes receives an audio signal from up to 4. Mute four independent audio sources. This 3.5mm non-shorting Stereo Remarks: There are other 4 Remote connector (Power, Mute, Gnd) is sources from Zone 1~4 as Remote designed to be used in conjunction Source Inputs R5 to R8 can be with the AMC PDM1 (Phone-Doorbell- selected by all zones. Mute Module) - This is an option Remote So
Inhaltszusammenfassung zur Seite Nr. 6
KEYPAD (XK1 for Zone 1 to 4) 6 10 7 1 98 5 2 (JK2) TO XOi 4 Rear Panel or JK3 of Main XK1 3 1. LED's of Volume Level of the zone 6. Source Selection Volume-only one LED will be lighted The 8 source buttons independently up. (for energy saving purposes) select any of the four local sources ( Source 1 to 4) connected to the rear 2. Volume up / down panel of AMC XOi main unit and four Remote Sources (Source R5 to R8) 3. IR Receiver connected to the XU1 of Zone 1 to 4. Each keypad has an IR receiver
Inhaltszusammenfassung zur Seite Nr. 7
8. JK2 (RJ45) (TO XOi Rear Panel) JK3 of XK1 to JK2 of Another XK1. - Use Cat-5 cable to connect from the This is an option feature. JK2 of XK1 to RJ45 of specific Zone on 10. JK4 (RJ45) (To SUB ZONE) XOi Rear Panel (or JK3 of Main XK1 - Use Cat-5 cable to connect from the option) JK4 of XK1 to main-in of amplifiers or power speakers. - This is an option 9. JK3 (RJ45) (ToAnother XK1) feature. Use Cat-5 cable to connect from the REMOTE SOURCE XS1 (for Zone 1 to 4) RCAJack Inputs (L& R) 3.5mm Mini
Inhaltszusammenfassung zur Seite Nr. 8
REMOTE CONTROL 1 2 3 4 1. Power On & Off "Mute On" and "Mute off" turn the mute This button turns the zone on and off "On" or "Off" and powers all the zones off when it is pressed and held. 4. Volume Perform the same function as the 2. Source Selection volume button on the zone keypads. These 8 buttons correspond to the four The volume level indicator on the local source buttons ( source 1~4) and keypad will respond correspondingly to four remote source buttons (source R5 the volume command from
Inhaltszusammenfassung zur Seite Nr. 9
INSTALLING THE XOi DIGITAL HOME SYSTEM 1. Prewire The XOi uses Cat-5 cable for keypad control and either two- or four-conductor 16- gauge speaker wire.All the wire is homerun from each zone to the XOi. 2. The XOi digital home systems require Cat-5, unshielded, twisted pair (UTP), for communication between the keypads/display pads and the main XOi unit. Each end of the wire is terminated with an RJ45 connector. The XOi system can accommodate 500 total feet of Cat-5 cable for each zone. For the mo
Inhaltszusammenfassung zur Seite Nr. 10
Step-by-Step Crimping instructions Step1 Stripa2to3 inches portion of the insulation, exposing the 4 twisted pairs. Step2 Untwist the wires and fan them out individually. Arrange the wires into the correct color scheme as shown in Fig.1 Step3 Flatten the wires in their correct order, and trim them evenly across the top. Most crimp tools have a wire trimmer built-in. It is best to trim the wires to about 1/2 in length. Step4 While holding the wires flat between your thumb and forefinger, insert t
Inhaltszusammenfassung zur Seite Nr. 11
4. Installing the XOi The XOi is designed to be placed on a shelf or in a component rack. If you are mounting the XOi with other components,you should remove the feet. The audio sources are plugged into the four local source inputs on the back panel of the XOi using stereo RCA cables, Fig.4 Source 1 Audio Out Tuner 1 5. IR Outputs The XOi system ships with four IRE1 IR Emitters for transferring IR data from the keypad receivers (located under the volume button) to the IR receiver on each piece o
Inhaltszusammenfassung zur Seite Nr. 12
6. Keypad XK1 and Zone Setup The Zone number each keypad XK1 belonging to is decided by which RJ45 connector each keypad connected through Cat-5 cable from JK2 of XK1 to XOi. EQ Control and Source Grouping The keypads can be used to set specific zone functions. These are for bass and treble EQ response and source grouping. To change bass response, press the Mute button and Source 2 button simultaneously. Adjust the bass level up or down by using the Volume Up and Volume Down buttons. The Volume
Inhaltszusammenfassung zur Seite Nr. 13
7. Using the Link Jack to create Eight Zones (This is an optional feature) Two XOi can be made to react as one using the back-panel 3.5mm connection labeled "Link". This requires the use of "Y" cables to link the source inputs and IR outputs. A single mono mini-patch cable is then plugged into the "Link" jack on both XOi. This links the All Off command so when it is initiated at any of the zone keypads, all eight zones will turn off. 8. Mute Input and theAMC PDM1 (Phone-Doorbell-Mute Module) (Th
Inhaltszusammenfassung zur Seite Nr. 14
SPECIFICATIONS Total Zones...........................................4 Zones Zone 1~4 with Speaker Outputs.................................15Wrmsx2 Sources.........................4Local/4RemoteMixedSources Sensitivity.................................................. 60mV IR outputs frequencies....................four38KHzandfour56KHz IR output level..................................................5Vp-p Phone input sensitivity.............................. AC25V~AC100V 20Hz Doorbell input sens
Inhaltszusammenfassung zur Seite Nr. 15
SAFETY INSTRUCTION 1.READ INSTRUCTIONS 16.DAMAGE REQUIRING SERVICE All the safety and operating instructions should be read The appliance should be serviced by qualified service beforetheapplianceisoperated. personnelwhen: a) Thepower-supplycordortheplughasbeendamaged;or 2.RETAIN INSTRUCTIONS b) Objects have fallen, or liquid has been spilled into the The safety and operating instructions should be retained for appliance;or futurereference. c) Theappliancehasbeenexposedtorain;or d) The appliance
Inhaltszusammenfassung zur Seite Nr. 16
WELTRONICS CORP. LONDON/L.A. AMC Web: http://www.amchome.com PN: 21R-4213
