Inhaltszusammenfassung zur Seite Nr. 1
®
Docking Digital Clock Radio Music System For iPod
OWNER’S MANUAL
JiMS-182
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT INSTRUCTIONS 1. Do not install the system near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 2. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 3. Only use attachments / accessories specified in these instructions. 4. Unplug this apparatus during lightning storms or when unused for long periods of ti
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT NOTES Avoid installing the unit in locations described below: Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters. Dusty, humid or moist places. Places subject to constant vibration. PROTECT YOUR FURNITURE This system is equipped with non-skid rubber ‘feet’ to prevent the product from moving when you operate the controls. These ‘feet’ are made from non-migrating rubber material specially formulated to avoid leaving any marks or
Inhaltszusammenfassung zur Seite Nr. 4
Display Segment SETTING UP AND CONNECTING This Portable Docking System is designed to operate on 4 x 1.5V ‘AA’ (UM-3) batteries (Not included) or the included AC Adaptor. A Lithium battery (Included) is also required for the backup of the clock. A. BATTERY OPERATION For outdoor or portable use, install 4 brand new, good quality alkaline-type batteries. Remove the battery doors on bottom of the cabinet. 1. Check the polarities and install 4 “AA” size (UM-3) batterie
Inhaltszusammenfassung zur Seite Nr. 5
batteries at the same time as soon as possible to avoid battery leakage. B. AC Adaptor Operation 1. Insert one end of the AC adaptor into the DC Jack on back of JiMS-182. 2. Connect the AC plug of the AC adaptor to an AC 120V~ 60Hz power source. Note: The batteries will be automatically disconnected when the AC adaptor is plugged into the DC Jack and the System will operate on AC power. Note: Unplug the AC adaptor and disconnect the DC Jack when the JiMS-182 is not in use for
Inhaltszusammenfassung zur Seite Nr. 6
Press the MEMO./SET button once. “12H” will appear and flash in the display. 2. Press or button once to select 24 Hour format (24 H) if desired. 3. Press the MEMO./SET button again to save the hour format setting. The Hour digit will blink. 4. While the Hour digit blinks, press or button repeatedly to set the current hour. Note: For 12 Hour format, make sure the Hour is correctly set so that AM or PM is correctly displayed. 5. Press the MEMO./SET button again to save the hour set
Inhaltszusammenfassung zur Seite Nr. 7
1. Press the POWER/STANDBY button to turn the unit on. 2. Press the / BAND button to select AM or FM band as desired. 3. Briefly press the ALM.2/MEM+ or ALM.1/ MEM- Button to select the preset channels. TIPS FOR BEST RECEPTION 1. Automatic tuning depends on the signal strength of the broadcasting station, so weak stations are sometimes skipped. Tune manually to find the weak stations. With stronger broadcast stations the tuner may stop before it reaches the station frequency or optimum
Inhaltszusammenfassung zur Seite Nr. 8
rd th nd For nano 3 generation For nano 4 generation For iTouch 2 generation It is always recommended you use the adaptor that comes with your iPod first. This will help maximize a custom fit for your iPod when docked. To place the iPod adapter 1. Select an adaptor and gently place it into the dock. Insert the hooks of the adaptor into the socket of the docking bay. 2. Carefully push forwards and press down the adaptor. To remove/replace the iPod adapter 1. Gently remove y
Inhaltszusammenfassung zur Seite Nr. 9
1. To set the wakeup time, press and hold the ALM.1 / MEM- or ALM.2 / MEM+ Button for approximately 3 seconds until the hour digit blinks. While the hour digit blinks, press or button to adjust your desired hour digit. Note: For the 12 Hour format, Make sure the Hour is set so that AM or PM is correctly displayed. 2. Press ALM.1 / MEM- or ALM.2 / MEM+ button to save the hour setting, the minute digit will blink. 3. While the minute digits blink, press or button to adjus
Inhaltszusammenfassung zur Seite Nr. 10
Stopping the Alarm The alarm is programmed to continuously sound for 60 minutes. To stop the alarm, follow the directions below. 1. SNOOZE / DIMMER Button – Press this button to stop the alarm temporarily. The alarm will stop and automatically resume after 9 minutes. 2. POWER/STANDBY Button – Press this Button to stop the alarm which will sound again 24 hours later. 3. ALM.1 / MEM- or ALM.2 / MEM+ Button – Press this Button once to stop the alarm and the alarm will sound again 24 hour
Inhaltszusammenfassung zur Seite Nr. 11
Turn on the JiMS-182 on and select either iPod, Radio or AUX function. 1. Press the SLEEP Button repeatedly until the desired sleep time is shown on the Display. For example, if it is 10:00 PM and you set the sleep time for 30 minutes, the display will show: Preset Sleep Time Current time 2. The JiMS-182 will play and turn off automaticall
Inhaltszusammenfassung zur Seite Nr. 12
Symptom Possible Cause Solution Radio Noise or sound distorted Station is not tuned properly Fine-tune the AM or FM on AM or FM for AM or FM. broadcast station. broadcasting. FM: The broadcast station Find another station or signal is weak relocate the unit until the best reception is obtained. AM: The location of the built-in Remove your iPod and antenna is not correct. rotate the unit until the best reception is obtained. AM or FM no sound Unit is not in RADIO function Press the F
Inhaltszusammenfassung zur Seite Nr. 13
included) CR2025 x 1 (Included) for memory back- up Dimension ------------------------- ------------ 6-7/8(W) x 7-1/2(D) x 1-7/8(H) Inch/ 174(W) x 190 (D) x 47(H) mm Weight ------------------------------------------- 1.32 lb/0.6kg TUNER SECTION Frequency range ----------------------------- FM: 87.5- 108MHz AM: 530-1710 KHz AUDIO SECTION Power Output -----------------------
Inhaltszusammenfassung zur Seite Nr. 14
This warranty is valid only in accordance with the conditions set forth below: 1. The warranty applies to the SPECTRA product only while: a. It remains in the possession of the original purchaser and proof of purchase is demonstrated b. It has not been subjected to accident, misuse, abuse, improper service, usage outside the descriptions and warnings covered within the owner’s manual or non-SPECTRA approved modifications c. Claims are made within the warranty period 2. This warranty does
