Inhaltszusammenfassung zur Seite Nr. 1
Crestron MMK-6X-DSW & WMKM-6X-DSW
Mud Mount Kits for the TPS-6X-DSW
Installation Guide
Inhaltszusammenfassung zur Seite Nr. 2
Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW Contents Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW 1 Description.................................................................................................................................1 Setup ..........................................................................................................................................2 Supplied Hardware ...........................................................
Inhaltszusammenfassung zur Seite Nr. 3
Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW Description Mud Mount Kits are the preferred mounting option for the TPS-6X-DSW when the cutout made in the drywall for docking station installation is too large. These kits provide support for additional plastering that can be applied to hide large irregularities in the cutout. NOTE: If mounting into a material other than drywall (for example, wood lectern, concrete
Inhaltszusammenfassung zur Seite Nr. 4
Mud Mount Kits for the TPS-6X-DSW Crestron MMK/WMKM-6X-DSW Setup Supplied Hardware The MMK-6X-DSW consists of three parts. These parts produce an assembly that attaches to the BB-6X-DSW or PMK-6X-DSW. The WMKM-6X-DSW consists of six parts, three of which make up the MMK-6X-DSW, as well as a mounting plate, a set of mounting screws and a cutout template. The mounting plate provides the necessary support for post-construction applications. An overlay cutout template (4506370) is supplied
Inhaltszusammenfassung zur Seite Nr. 5
Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW Dimensional Drawing – Adjustment Plate 0.38 in (0.95 cm) 10.24 in (26.01 cm) 0.38 in (0.95 cm) Dimensional Drawing – Mounting Plate 10.31 in (26.19 cm) 0.06 in 8.00 in (0.15 cm) (20.32 cm) 8.82 in (22.39 cm) 6.35 in (16.13 cm) Installation Guide – DOC. 6779A Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW • 3
Inhaltszusammenfassung zur Seite Nr. 6
Mud Mount Kits for the TPS-6X-DSW Crestron MMK/WMKM-6X-DSW Drywall Cutout Template and Dimensions (supplied with WMKM-6X-DSW only) 9 1/16 in (230 mm) 7 11/16 in (196 mm) 6 1/8 in (156 mm) 6 9/16 in (167 mm) Installation This section provides an installation procedure for each Mud Mount Kit. The “MMK-6X-DSW Procedure” starts below and the “WMKM-6X-DSW Procedure” starts on page 7. Be sure to review each procedure before starting. MMK-6X-DSW Procedure This section provides the necessary s
Inhaltszusammenfassung zur Seite Nr. 7
Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW NOTE: The illustrations in this procedure show the installation of the MMK-6X-DSW with the PMK-6X-DSW. Even though the illustrations only show the PMK-6X-DSW, they are identical for the BB-6X-DSW. 1. Pass an adjustment plate through the opening and align its two center holes with the top two pins on the PMK-6X-DSW. Verify that the pins on the adjustment plate are not between (facing) the adjustment plate and the PMK-6X-DSW. Refe
Inhaltszusammenfassung zur Seite Nr. 8
Mud Mount Kits for the TPS-6X-DSW Crestron MMK/WMKM-6X-DSW Insert and Secure Mud Ring Plate into PMK-6X-DSW (or BB-6X-DSW) DRYWALL PMK-6X-DSW DRYWALL SCREWS (NOT INCLUDED) SCREW LENGTH SHOULD NOT EXCEED DRYWALL THICKNESS BY MORE THAN 1/2" (13 MM). MUD RING PLATE (2022809 ) 5. When the mud ring plate is in position, bend the top two flanges of the plate upward and the bottom two flanges downward. • If mounting into the PMK-6X-DSW, bend the flanges approximately 90 degrees. • If mounti
Inhaltszusammenfassung zur Seite Nr. 9
Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW 9. Apply drywall joint compound as needed to finish the cutout. Avoid covering the four tapped mounting holes. 10. Run the necessary cables for the TPS-6X-DSW and secure them behind the drywall. 11. When dry, the wall mount docking station can be installed using the four tapped holes in the PMK-6X-DSW. Refer to the latest revision of the TPS-6X-DSW Operations and Installation Guide (Doc. 6708) for installation instructions. Refe
Inhaltszusammenfassung zur Seite Nr. 10
Mud Mount Kits for the TPS-6X-DSW Crestron MMK/WMKM-6X-DSW CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity above and below the TPS-6X-DSW for heat dissipation. 1. Insert the two pins on one adjustment plate into the top two outer holes on the mounting plate, as shown in the illustration below. Create the Adjustment/Mounting Plate Assembly PUSH ON FASTENER (4) (2004121 ) MOUNTING PLATE (2022811 ) ADJUSTMENT PLATE (2) (2017631 ) 2. Slide a push-on fastener o
Inhaltszusammenfassung zur Seite Nr. 11
Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW NOTE: Make the cutout as level as possible. The mounting plate allows for only minor leveling adjustments. 6. Use the drywall saw or equivalent and the included drywall cutout template to produce an accurate and level cutout in the drywall. 7. Insert the symmetrical mud ring plate into the opening, as shown in the illustration below. Insert Mud Ring Plate into Opening DRYWALL DRYWALL SCREWS (NOT INCLUDED) SCREW LENGTH SHOULD NOT
Inhaltszusammenfassung zur Seite Nr. 12
Mud Mount Kits for the TPS-6X-DSW Crestron MMK/WMKM-6X-DSW Bend Flanges – 1 of 4 Flanges Bent BACK OF DRYWALL 10. Use four standard drywall screws (length should not exceed drywall thickness by more than 1/2 inch) to secure the mud ring plate to the adjustment/mounting plate assembly. The screws are secured in the extruded holes of the adjustment plate and pass through the clearance holes in the mounting plate. 11. Verify that the plate is level before tightening. NOTE: Do not over t
Inhaltszusammenfassung zur Seite Nr. 13
Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW TPS-6X-DSW Mounting Using WMKM-6X-DSW – Exploded View PUSH-ON FASTENERS (4) (2004121 ) MOUNTING PLATE (20022811 ) ADJUSTMENT PLATE (2) (2017631 ) DRYWALL MUD RING (2022809 ) TPS-6X-DSW DRYWALL SCREWS (NOT INCLUDED) SCREW LENGTH SHOULD NOT EXCEED DRYWALL THICKNESS BY MORE THAN 1/2" (13 MM). SCREW #06-32 1 1/2" PAN HEAD (2007254 ) Installation Guide – DOC. 6779A Mud Mount Kits for the TPS-6X-DSW: MMK-6X-DSW & WMKM-6X-DSW • 11
Inhaltszusammenfassung zur Seite Nr. 14
Mud Mount Kits for the TPS-6X-DSW Crestron MMK/WMKM-6X-DSW Resources Industry Compliance As of the date of manufacture, the MMK-6X-DSW and WMKM-6X-DSW have been tested and found to comply with specifications for CE marking. Reference Documents The latest version of all documents mentioned within the guide can be obtained from the Crestron website (www.crestron.com/manuals). This link will provide a list of product manuals arranged in alphabetical order by model number. List of Relat
Inhaltszusammenfassung zur Seite Nr. 15
Crestron MMK/WMKM-6X-DSW Mud Mount Kits for the TPS-6X-DSW Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem
Inhaltszusammenfassung zur Seite Nr. 16
Crestron Electronics, Inc. Installation Guide – DOC. 6779A 15 Volvo Drive Rockleigh, NJ 07647 (2023087) Tel: 888.CRESTRON 01.09 Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.
