Inhaltszusammenfassung zur Seite Nr. 1
R
1275 Danner Dr Tel:330-562-7070
NETWORK
TECHNOLOGIES Aurora, OH 44202 Fax:330-562-1999
INCORPORATED www.nti1.com
NTI
INSTALLATION GUIDE FOR THE VOPEX PS/2 KEYBOARD,
MONITOR & MOUSE SPLITTER
MAN046 Last Revised 8/30/02
Inhaltszusammenfassung zur Seite Nr. 2
WARRANTY INFORMATION The warranty period on this product (parts and labor) is one (1) year from the date of purchase. Please contact Network Technologies Inc at (800) 742-8324 (800-RGB-TECH) in US and Canada or (330) 562-7070 (worldwide) for information regarding repairs and/or returns. A return authorization number is required for all repairs/returns. COPYRIGHT Copyright© 2002 by Network Technologies Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrie
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS INTRODUCTION............................................................................................................................................................................1 Available Options........................................................................................................................................................................1 MATERIALS....................................................................................................
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION This VOPEX allows 1 IBM compatible CPU to support multiple users (up to 4, depending on the VOPEX model). The devices (keyboards and mice) of many different manufacturers can be plugged into the VOPEX when powering up. Also, any combination of devices will work. (e.g. a mouse on port 2, keyboards on ports 3 & 4). Hot plugging devices at any time is fully supported with the possible exceptions listed in “MOUSE SPECIAL CONSIDERATIONS” (see page 3). Available Options • VOPEX mode
Inhaltszusammenfassung zur Seite Nr. 5
CONNECTING THE VOPEX TO THE CPU 1. Turn OFF power to the CPU that will be connected to the VOPEX before connecting or disconnecting any cables. WARNING! If power to the CPU is not turned OFF before connecting or disconnecting cables, damage to the CPU may result. 2. Connect the CPU to the VOPEX as follows (see Figures 1 and 2): a) Connect a VEXT-3 cable from the video port of the CPU to the male 15HD port labeled "VGA CPU" on the VOPEX. b) Connect a purple male 6 miniD
Inhaltszusammenfassung zur Seite Nr. 6
Installing the Optional Monitor(s) 1. Plug all monitors into AC power outlets. 2. Turn OFF power to the monitors that will be connected to the VOPEX before connecting them. 3. Connect a monitor to the VGA MON1 port on the back of the VOPEX. See Figures 1 and 2. Note: A monitor must be connected to the VGA MON1 port for the monitor device driver to function properly. 4. Connect any other monitors to any of the other VGA MON ports on the back of the VOPEX. Installing the Optional Mouse(Mice) 1. C
Inhaltszusammenfassung zur Seite Nr. 7
DIAGNOSTIC INFORMATION At power up, the VOPEX uses the mode LEDs on the front panel to report some status. The sequence of events is as follows: 1. When unit is first powered, the LED state is indeterminate. 2. All LEDs are turned OFF, then flashed ON and OFF to indicate processor activity. 3. One LED for each keyboard detected is flashed ON and OFF. 4. One LED for each mouse detected is flashed ON and OFF. 5. The LEDs are left in the proper mode status (see “MODES OF OPERATION ”). MODES OF OPE
Inhaltszusammenfassung zur Seite Nr. 8
TROUBLESHOOTING If any problems are experienced with the VOPEX switch, follow the steps below to see if the problem(s) can be easily corrected: 1. Verify that all cables are securely connected. 2. Verify that a monitor is connected to Port 1. 3. If a user has both a keyboard and mouse, verify that they are connected to a Keyboard port and Mouse port with the same port number. 4. If a cable is disconnected: a) Turn OFF power to the CPU. b) Turn OFF power to the VOPEX. c) Connect the cable. d) Go
