Inhaltszusammenfassung zur Seite Nr. 1
SocketModem
Embedded Modem
MT5600SMI Family
MT5600SMI-32
MT5600SMI-L32
MT5600SMI-P32
MT5600SMI-34
MT5600SMI-L34
MT5600SMI-XL34
MT5600SMI-P34
MT5600SMI-PL34
MT5600SMI-92
MT5600SMI-L92
MT5600SMI-XL92
MT5600SMI-P92
MT5600SMI-PL92
Developer’s Guide
Inhaltszusammenfassung zur Seite Nr. 2
Copyright and Technical Support SocketModem Developer's Guide MT5600SMI (MT5600SMI-32, MT5600SMI-L32, MT5600SMI-P32, MT5600SMI-34, MT5600SMI-L34, MT5600SMI-XL34, MT5600SMI-P34, MT5600SMI-PL34, MT5600SMI-92, MT5600SMI-L92, MT5600SMI-XL92, MT5600SMI-P92, MT5600SMI-PL92) PN S000306A, Version A Copyright This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2002-2003, by Multi-Tech Syste
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents Contents Chapter 1 – Product Description and Specifications................................................................................ 5 Introduction................................................................................................................................................ 5 Product Description ................................................................................................................................... 5 Features...................
Inhaltszusammenfassung zur Seite Nr. 4
Table of Contents Compatibility Commands.....................................................................................................................70 FastConnect Commands .....................................................................................................................71 V.92 +P and –Q Commands................................................................................................................71 S-Registers..................................................
Inhaltszusammenfassung zur Seite Nr. 5
Chapter 1 – Product Description and Specifications Chapter 1 – Product Description and Specifications Introduction The Multi-Tech SocketModem creates communication-ready devices by integrating data functionality into a single product design. The SocketModem is a space-efficient (1" × 2.5"), embedded modem that provides V.92 or V.34/33.6K data communication. The complete, ready-to-integrate modem dramatically reduces development time and costs for system designers. The SocketModem complies with t
Inhaltszusammenfassung zur Seite Nr. 6
Chapter 1 – Product Description and Specifications Developer's Kit A Developer's Kit is available. The serial kit allows you to plug in the SocketModem and use it as a serial modem for testing, programming, and evaluation. The parallel kit turns the parallel module into an ISA modem. Each kit includes one SocketModem, one development board with an RS-232 DB-25 connector, wall power adapter, RJ-11 jack, and RS-232 cable. Features Integrates the controller, data pump, and data access arrangement
Inhaltszusammenfassung zur Seite Nr. 7
Chapter 1 – Product Description and Specifications Technical Specifications The SocketModem meets the following specifications: Data Format Serial or parallel interface Data V.92; V.90, V.34, V.32bis, V.32, V.22bis, V.22, V.23, V.21,Bell 212A & Bell 103 Error Correction V.42 (LAP-M or MNP 2–4) Data Compression V.42bis, MNP 5 Fax V.17, V.29, V.27ter, V.21 ch.2 Class 1 and 1.0 commands Modes of Operation Full duplex over dial-up lines; data mode, command mode, online command mode Advanced Extensio
Inhaltszusammenfassung zur Seite Nr. 8
Chapter 2 – Mechanical Specifications Chapter 2 – Mechanical Specifications Physical Dimensions Figure 2–1. Maximum Component Height Multi-Tech Systems, Inc. SocketModem MT5600SMI Developer’s Guide 8
Inhaltszusammenfassung zur Seite Nr. 9
Chapter 2 – Mechanical Specifications Serial Pin Configurations The serial interface use an 16-pin interface to provide an on-board DAA with tip and ring connections, audio circuit for call-progress monitoring and serial interface via logic level signals. Figure 2–2. Serial SocketModems Pins Available with or without LED Pins Pin Descriptions for Serial SocketModem Devices Pin Signal I/O Description # Name Type 1 Tip I/O Tip Signal from Telco. Tip connection to the phone line (RJ11 Pin 3). Socke
Inhaltszusammenfassung zur Seite Nr. 10
Chapter 2 – Mechanical Specifications Pin Signal I/O Description # Name Type 31 DTRIND DTR LED. Output from 74AC05 with 1500 Ohms pull-up. 32 TXIND TX LED. Output from 74AC05 with 1500 Ohms pull-up. 33 –RTS I Request to Send. RTS signal is used for hardware flow control. 34 –RXD O Received Data. Used to send data received from the telephone line and also modem responses to the DTE. Modem response take priority over incoming data. When no data is transmitted, the signal is held in mark condition
Inhaltszusammenfassung zur Seite Nr. 11
Chapter 2 – Mechanical Specifications Parallel Pin Configurations The parallel interface SocketModem uses a 22-pin interface to provide an on-board DAA with tip and ring connections, audio circuit for call-progress monitoring, and parallel interface. Figure 2–3. Parallel SocketModem Pins Pin Descriptions for a Parallel SocketModem Device Pin # Signal Name I/O Description 1 Tip I/O Telephone Line Interface – TIP 2 Ring I/O Telephone Line Interface – RING 24 –RESET I Modem Reset
Inhaltszusammenfassung zur Seite Nr. 12
Chapter 2 – Mechanical Specifications Pin # Signal Name I/O Description 32 –WT I Host Bus Write. When low, allows host to write to SocketModem. 33 –RD I Host Bus Read. When low, allows host to read from SocketModem. 34 A2 I Host Bus Address Line 2 35 D4 O Host Bus Data Line 4 36 D5 O Host Bus Data Line 5 37 D0 O Host Bus Data Line 0 38 D1 O Host Bus Data Line 1 39 D3 O Host Bus Data Line 3 40 –CS I Host Bus Chip Select; active low 41 D6 O Host Bus Data Line 6 61 VCC PWR 3.3V or 5V Supply (de
Inhaltszusammenfassung zur Seite Nr. 13
Chapter 3 – Electrical Characteristics Chapter 3 – Electrical Characteristics Handling Precautions All electronic devices should be handled with certain precautions to avoid damage due to the accumulation of static charge. Although input protection circuitry has been incorporated into the devices to minimize the effect of this static buildup, proper precautions should be taken to avoid exposure to electrostatic discharge during handling and mounting. I/O Electrical Characteristics 3.3V Serial So
Inhaltszusammenfassung zur Seite Nr. 14
Chapter 3 – Electrical Characteristics 5V Serial SocketModem 5 Vdc Characteristics (TA = 0 °C to 50 °C; VDD = 5 V ± 0.25 V) VDDMAX = 5.25 V Digital Inputs Input High Input Low –DTR (40), –TXD (35), –RTS (33), –RESET (24) Min 3.5 V Max .8 V Digital Outputs Output High Output Low Current Drive –DCD (39), –CTS (38), –DSR (37), –RI (36), –RXD (34) Min 4 V Max 0.5 V 15 ma Digital Input Capacitance 5 PF 5V Parallel SocketModem 5 Vdc Characteristics (TA = 0 °C to 50 °C; VDD = 5 V ± 0.25 V) VDD
Inhaltszusammenfassung zur Seite Nr. 15
Chapter 3 – Electrical Characteristics Current and Power Requirements Typ. Max. Typ. Max. Mode Current (mA) Current (mA) Power (mW) Power (mW) +3.3 V Configuration (VDD = +3.3 V) Normal Mode (Serial interface) 115 116 0.38 0.41 +5 V Configuration (VDD = +5 V) Normal Mode (Serial interface) 117 118 0.58 0.61 Normal Mode (Parallel interface) 117 118 0.58 0.61 Test conditions: For Pin 61 = +5 V, VDD = +5 V for typical values; VDD = +5.25 V for maximum values. For Pin 61 = +3.3 V, VDD = +3.3 V for t
Inhaltszusammenfassung zur Seite Nr. 16
Chapter 3 – Electrical Characteristics Parallel Host Bus Timing Parallel Host Bus Timing Table Symbol Parameter Min Max Units READ (See Notes) t Address Setup 5 - ns AS t Address Hold 10 - ns AH t Chip Select Setup 0 - ns CS t Chip Select Hold 10 - ns CH t RD Strobe Width 45 - ns RD t Read Data Delay - 25 ns DD t Read Data Hold 5 - ns DRH WRITE (See Notes) t Address Setup 5 - ns AS t Address Hold 15 - ns AH t Chip Select Setup 0 - ns CS t Chip Select Hold 10 - ns CH t WT S
Inhaltszusammenfassung zur Seite Nr. 17
Chapter 3 – Electrical Characteristics Parallel Host Bus - Read Parallel Host Bus - Write Multi-Tech Systems, Inc. SocketModem MT5600SMI Developer’s Guide 17
Inhaltszusammenfassung zur Seite Nr. 18
Chapter 4 – SocketModem Parallel Interface – A Programmer's Description Chapter 4 – SocketModem Parallel Interface – A Programmer’s Description SocketModem Parallel Interface The modem supports a 16550A interface in parallel interface versions. The 16550A interface can operate in FIFO mode or non-FIFO mode. Non-FIFO mode is the same as the 16450 interface operation. FIFO mode’s unique operations are described in this chapter. Overview The modem emulates the 16450/16550A interface and includes bo
Inhaltszusammenfassung zur Seite Nr. 19
Chapter 4 – SocketModem Parallel Interface – A Programmer's Description Table 4–1. Parallel Interface Registers Register Register BIT No. No. Name 7 6 5 4 3 2 1 0 7 Scratch Register (SCR) Scratch Register 6 Modem Status Register Data Ring Data Set Clear to Delta Data Trailing Delta Data Delta Clear (MSR) Carrier Indicator Ready Send CTS) Carrier Edge of Ring Set Ready to Send Detect (RI) (DSR) Detect Indicator (DDSR) (DCTS) (DCD) (DDCD) (TERI) 5 Line Status Register RX Transmitter Transmitter Br
Inhaltszusammenfassung zur Seite Nr. 20
Chapter 4 – SocketModem Parallel Interface – A Programmer's Description Register Signal Definitions IER – Interrupt Enable Register (Addr = 1, DLAB = 0) The IER enables five types of interrupts that can separately assert the HINT output signal (Table 4– 2.). A selected interrupt can be enabled by setting the corresponding enable bit to a 1, or disabled by setting the corresponding enable bit to a 0. Disabling an interrupt in the IER prohibits setting the corresponding indication in the IIR and a
