Inhaltszusammenfassung zur Seite Nr. 1
OVER THE RANGE MICROWAVE OVEN/HOOD SYSTEM
INSTALLATION INSTRUCTIONS
Please read all instructions thoroughly before installing the Microwave Oven/Hood System. Two people are
recommended to install this product.
If a new electrical outlet is required, its installation should be completed by a qualified electrician before the
Microwave Oven/Hood is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.
12"
1 MOUNTING SPACE
15.5"
This Microwave Oven/Hood requires a mounting space on a wall
30
Inhaltszusammenfassung zur Seite Nr. 2
3 ELECTRICAL GROUNDING INSTRUCTIONS This appliance must be grounded. This oven is equipped with a cord having a grounding wire with a ground- ing plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, ground- ing reduces risk of electric shock by providing an escape wire for the electric current. WARNING - Improper use of the grounding plug
Inhaltszusammenfassung zur Seite Nr. 3
6 INSTALLATION HARDWARE The INSTALLATION HARDWARE (items 1-7) packed with the oven should contain the following: ITEM NAME QUANTITY PART CODE 1 Wood Screw 5 X 30 mm 6 XTSS750P35000 2 Toggle Bolt #10 - 24 X 50 mm 4 LX-BZ0195WRE0 3 Top Cabinet Screw 5 X 60 mm 2 XBRS750P60000 4 Flat Washer 30 mm diameter 2 XWHS750-16300 5 Grommet 1 LBSHC0040MRE0 6 Tapping Screw 4 x 12 mm 1 XOTS740P12000 7 Exhaust Damper Assembly 1 FFTA-B004MRK0 Figure 5 7 PREPARATION OF THE OVEN Utilization of the carton may make i
Inhaltszusammenfassung zur Seite Nr. 4
8 PREPARATION OF THE OVEN Figure 7 1. Rest the oven on its side as shown in Figure 7. Place portion (C) of the carton underneath to protect the outercase from being damaged. 2. Remove the two screws which secure the mounting plate to the rear side of the oven. Remove the mounting plate. The two screws can be discarded. NOTE: If the unit you purchased does not have the mounting plate attached to the rear side of the oven, please disregard this section and continue to Section 9. Mounting plate Gre
Inhaltszusammenfassung zur Seite Nr. 5
Mounting Plate (Back side) Figure 12 Wire Box Figure 11 Fan Cover Bracket C. VERTICAL EXHAUST: Outside Ventilation 1. Remove and save the 4 screws from the Fan Cover Bracket. Remove Fan Cover Bracket by sliding it in the opposite direction of the arrow on the Fan Cover Bracket as shown in Figure 13. 2. Lift the Hood Fan Unit carefully and slip wires out of cavity. See Figure 14. CAUTION: Do not pull or stretch hood fan wiring. 3. Rotate the Hood Fan Unit 180˚ so that the fan blade openings are
Inhaltszusammenfassung zur Seite Nr. 6
10 OVEN INSTALLATION THIS OVEN CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO THE MOUNTING INSTRUCTIONS FOUND ON BOTH TEMPLATES. READ AND FOLLOW MOUNTING INFORMATION ON BOTH TOP CABINET AND WALL TEMPLATES. MOUNTING PLATE 1. Separate 4 Toggle Bolts 2, packed in the INSTALLATION HARDWARE, from the Toggle Nuts. 2. Use Wood Screws 1 to attach Mounting Plate to the stud or studs. Use Toggle Bolts to attach Mounting Plate through the holes at A, B, C and D; UNLESS THOSE HOLES ARE LOCATED ON THE STU
Inhaltszusammenfassung zur Seite Nr. 7
4. Thread the power supply cord through the hole made in the bot- tom of the top cabinet. 5. Hang the oven on the lower edge of the mounting plate. Rotate the unit upward. See Figure 22. Take care that the power cord is able Hang at these to clear the edge of the hole as the oven is rotated upward. (In the locations case of a non-recessed bottom in the top cabinet, the hole for the cord may need to be enlarged.) Remove the carton portions. 6. Tighten the two unit mounting screws located in the g
Inhaltszusammenfassung zur Seite Nr. 8
CHECK LIST FOR INSTALLATION 1. Make sure the unit has been installed according to all of the Installation Instructions, the Top Template and Wall Template. 2. Remove all packing material from the oven. 3. Plug in the power cord. 4. Read the Operation Manual. 5. Keep the Installation Instructions for the local electrical inspector’s use. ACCESSORIES Check with your dealer or order directly from the SHARP Accessories and Supplies Center. Call toll-free 1-800-BE SHARP (237-4277). 1. CHARCOAL FILT
