Bedienungsanleitung Frigidaire TINSEB151WRRZ

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS
Over The Range Microwave Oven
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT
• Save these instructions for local
• Proper installation is the responsibility of the installer.
inspector’s use.
• Product failure due to improper installation is not covered
IMPORTANT
• Observe all governing codes and
under the Warranty.
coordinates.
• Please read all instructions thoroughly before installing
• NOTE TO INSTALLER – Be sure to l

Inhaltszusammenfassung zur Seite Nr. 2

INSTALLATION INSTRUCTIONS 3 ELECTRICAL GROUNDING INSTRUCTIONS 4 HOOD EXHAUST DUCT This appliance must be grounded. This oven is equipped with When the hood is vented to the outside, a hood exhaust duct a cord having a grounding wire with a grounding plug. It must is required. All ductwork must be metal; absolutely do not use be plugged into a wall receptacle that is properly installed and plastic duct. Check that all connections are made securely. grounded in accordance with the National Ele

Inhaltszusammenfassung zur Seite Nr. 3

INSTALLATION INSTRUCTIONS 5 TOOLS RECOMMENDED FOR 7 PREPARATION OF THE OVEN INSTALLATION 1. Open the bottom of the carton, bend the carton flaps back and tilt the oven over to rest on plastic foam pad. Lift carton • Phillips Screwdriver off oven and remove all packing materials, Installation • Electric Drill Instructions, Wall Template, Top Template, Charcoal Filter, Turntable and Turntable Support; however, DO • ¹⁄₂", ⁵⁄₈" and ³⁄₃₂" Drill Bits NOT REMOVE THE WAVEGUIDE COVER, wh

Inhaltszusammenfassung zur Seite Nr. 4

INSTALLATION INSTRUCTIONS (B) HORIZONT AL EXHAUST : OUTSIDE VENTILATION 8 VENTILATION SYSTEM (PREPARING OVEN FOR INSTALLATION) 1. Remove and save 2 screws from back edge and 1 screw from the top center of Fan Cover Bracket. Remove Fan This microwave oven/hood is designed for adaptation to three Cover Bracket by sliding it in the opposite direction of the types of hood ventilation systems. Select the type required arrow on the Fan Cover Bracket, as shown in Figure 7. for y

Inhaltszusammenfassung zur Seite Nr. 5

INSTALLATION INSTRUCTIONS Fan Cover Bracket Rotate 90° Figure 11 Exhaust Damper Assembly 9 OVEN INSTALLATION THIS OVEN CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO THE MOUNTING INSTRUCTIONS FOUND ON BOTH TEMPLATES. Tapping Screw THE NEXT STEP IS TO READ AND FOLLOW MOUNTING INFORMATION ON BOTH TOP CABINET AND WALL TEMPLATES. Figure 10 NOTE: THIS OVEN SHOULD BE ATTACHED TO AT LEAST ONE WALL STUD. 8 VENTILATION SYSTEM MOUNTING PLATE (PREPARING OVEN FOR INSTALLATION) 1. Se

Inhaltszusammenfassung zur Seite Nr. 6

INSTALLATION INSTRUCTIONS 9 OVEN INSTALLATION cont. Toggle Bolt Toggle Nut Mounting Plate Figure 12 Space more than wall thickness Figure 15 Figure 14 Wall Figure 13 MOUNTING OVEN TO THE WALL Two people are recommended to attach the Microwave Oven/ Hood to the Mounting Plate. Tapping Screw 1. Thread the power supply cord through the hole made in the bottom of the top cabinet. Figure 16 2. Install the oven by tilting it forward and sliding it onto the Tapping Screw tabs of the Mounting Plate.

Inhaltszusammenfassung zur Seite Nr. 7

INSTALLATION INSTRUCTIONS CHECKLIST FOR INSTALLATION 1. Make sure the unit has been installed according to all of the Installation Instructions and the Wall and Top Cabinet Templates. 2. Plug in the power cord. 3. Keep the Operation Manual. E7

Inhaltszusammenfassung zur Seite Nr. 8

NOTES E8