Inhaltszusammenfassung zur Seite Nr. 1
Operation Manual
LRB 6000CI
LASER RANGE FINDER
BINOCULARS
105 Sparks Ave., Toronto, ON M2H 2S5, Canada
Inhaltszusammenfassung zur Seite Nr. 2
ii
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT INFORMATION Read prior to activation You have just purchased a sophisticated electro-optical device that emits invisible laser radiation. To operate it properly, please read this manual carefully. NEVER direct laser beam at the eyes of people or animals NEVER aim the unit at the Sun or bright sources of light NEVER subject the unit to impacts NEVER transport the unit without its case NEVER disassemble the unit. This may be hazardous for you due to high voltage
Inhaltszusammenfassung zur Seite Nr. 4
Caution - use of optical instruments such as binoculars, loupes, mirrors, lenses, etc. with this product increases eye hazard Note: Avoid eye exposure to direct laser beam or its close reflection Prevent bright light from focusing through the eyepieces Never aim the unit at highly reflective objects like mirrors and retroreflective surfaces, which are in close proximity to the laser rangefinder. This can lead to the permanent damage of the photoreceiver incorporated into the d
Inhaltszusammenfassung zur Seite Nr. 5
TABLE OF CONTENTS 1. BRIEF DESCRIPTION.................................................. 2 2. DEVICE APPEARANCE..............................................4 3. DELIVERY SET............................................................7 4. SPECIFICATIONS ........................................................ 8 5. OPERATION INSTRUCTIONS.................................. 10 Installing the battery..................................................... 10 Using the Device .....................
Inhaltszusammenfassung zur Seite Nr. 6
CAREFULLY READ ALL THE INSTRUCTIONS PRIOR TO USE! FAILURE TO OBEY THE INSTRUCTIONS WILL VOID THE WARRANTY AND MAY CAUSE INJURY! 1. BRIEF DESCRIPTION LRB 6000CI Laser Rangefinder Binoculars (System) is an advanced laser range finder system that enables instant distance, speed, vertical and horizontal angular measurements. An outstanding optics provides a sharp, clear image under any observation conditions. The unit utilises time-of-flight method of distance and speed measurement. Th
Inhaltszusammenfassung zur Seite Nr. 7
Key Features of the LRB 6000CI Laser Rangefinder Binoculars Modern digital circuitry allows targeting through most types of glass First, last or the most reflective target acquisition Meters/Yards/Mils/Degrees/KMH/MPH display Last 10 measurements recall Selectable reticle shape (+ or ) Gating capability Speed detector Accurate digital compass Accurate digital inclinometer RS-232 bidirectional communication GPS interoperability (PLGR/DAGR protocol) Auto sh
Inhaltszusammenfassung zur Seite Nr. 8
2. DEVICE APPEARANCE 4 6 1 7 5 8 3 2 Fig. 1. Front view 1 – Eyepieces 2 – Objective / receiving lens 3 – Objective / emitting 4 – Dioptric adjustment rings lens 5 – Mode button 6 – Action button 7 – Body of the device 8 – Rubber grip 4
Inhaltszusammenfassung zur Seite Nr. 9
1 9 10 11 Fig. 2 Rear view 1 – Eyepiece 9 – Interpupillary distance adjustment lever 10 – Model Identification label 11 – Identification and certification label (at the bottom): 5
Inhaltszusammenfassung zur Seite Nr. 10
6 1 8 7 2 4 3 Fig. 3 Display 2 – Reticle (either -¦- or ) 1 – Low battery indicator 3 – Units of measurement 4 – Measurement result 5 – Gating indicator 6 – Laser active indicator 7 – Ready mode indicator 8 – Setup mode indicator 6
Inhaltszusammenfassung zur Seite Nr. 11
3. DELIVERY SET Standard delivery set for LRB 6000CI includes: Qty LRB 6000CI 1 pc. Carrying case 1 pc. Neck strap 1 pc. User’s manual 1 pc. Warranty card 1 pc. Cleaning cloth 1 pc. Computer cable 1 pc. CD with communication software 1 pc. Hard case 1 pc. 9V non-magnetic Lithium battery 1 pc. Optional items GPS cable Exact delivery set depends on details of a contract or purchase order. 7
Inhaltszusammenfassung zur Seite Nr. 12
4. SPECIFICATIONS Optics Magnification 7x Objective lens diameter 50 mm Exit pupil diameter 7.1 mm Field of view 5 Type of coating Fully multi-coated optics Interpupillary distance 58-72 mm Dioptre adjustment range ±4 Range Finder Laser Class 1, eye safe, 905 nm Measuring range 1 – 6,500 m Accuracy and display 1 m resolution First, last and auto target Yes selection Meters / Yards display Yes Last 10 measurements recall Yes Reticle -¦- or Gating capability 100 – 3,900
Inhaltszusammenfassung zur Seite Nr. 13
Compass Measured azimuth range 6400 mils /360 Accuracy ±1 Inclinometer Measured elevation range ±60 Accuracy ±1 Height measuring Yes (Meters or Yards) Power Battery 9V Lithium (non-magnetic) Battery capacity Min 5,000 measurements (Scanning regime) 'Low Battery' indicator Yes Environmental o Operational temperature range -25…+50 C o (-13…+122 F) o Storage temperature range -45…+65 C o (-49…+149 F) Mechanics Tripod thread ¼” x 20 TPI Weight without batter
Inhaltszusammenfassung zur Seite Nr. 14
5. OPERATION INSTRUCTIONS Installing the battery Open the battery compartment using a suitable tool, or a coin. Insert a 9V Lithium non-magnetic battery provided with your device Connect the battery to the battery snap Refit the battery compartment and tighten the screw. If the battery compartment cover does not close tightly and evenly, check that the battery snap wires are neatly packed inside the battery compartment and the cover is aligned over the edge of the battery compa
Inhaltszusammenfassung zur Seite Nr. 15
Using the Device The LRB 6000CI operational procedures are design to allow the user to use most applicable options in the fastest time possible. To activate it, press and hold Action button (6, Fig.1) for one second. At start the unit comes into Ready to Measure mode indicated by the word ‘READY’ on the display visible through the eyepiece. Pressing Action button (6, Fig. 1) again will initiate measurement procedure. The results of measurement are displayed in default form of “Distance
Inhaltszusammenfassung zur Seite Nr. 16
Factors affecting measuring distance Though maximum measurement distance depends on target reflectivity, weather conditions and other conditions, for most targets the unit will provide accurate ranging for up to 4,000 meters. Under good conditions a large size target can be measured up to 6,500 meters. Target reflectivity depends on its color, surface finish, size, shape, position in relation to the laser beam, etc. Bright target colors are more reflective than darks. A polished surface
Inhaltszusammenfassung zur Seite Nr. 17
Target selection logic On its way towards the target the laser beam may be reflected from various objects, thus decreasing ranging accuracy. The smaller, the farther, and the less reflective is the target – the higher is the possibility of obtaining an incorrect measurement. To improve accuracy the unit has a built-in target selection logic that allows user the option of choosing which target to range: the nearest (‘first’), the farthest (‘last’), or the most reflective (‘auto’). Th
Inhaltszusammenfassung zur Seite Nr. 18
Scanning regime the unit repeatedly measures and displays results every second while A button is pressed. To activate Scanning regime press and hold Action button in Ready mode. The unit will work in Scanning regime while Action button is pressed. Scanning or Individual Measurement regimes are available for any selected mode of measurement. When two or more parameters are measured in Scanning regime though first result will be displayed, the second and other results will be shown at t
Inhaltszusammenfassung zur Seite Nr. 19
Std – allows the user to select single action measurements: o Distance only (d) o Compass Only (C) o Elevation Only (E) o Speed Only (S) o Height Only (H) o Speed + Distance (Sd) o Distance +Compass + Elevation (dCE) Unit – allows the user to select units of desired measurements, o Distance from M to Y o Compass & Elevation from Mils to Degrees o Speed from KMH to MPH* * this option is only available if Std Speed is selected rEc – allows data recall of the last 10 me
Inhaltszusammenfassung zur Seite Nr. 20
o AUtO – Last Target Measurement* o PLGr – Communication to PLGR GPS* o PC – Communication to PC* o Reticule – Change reticule from + (cross) to (rectangle) o CAL – Compass calibration ▪ CALc – compass calibration (CI model only) ▪ Corr – accuracy correction of active parameters *not shown in the menu if currently selected Accuracy correction If the System produces any measurement errors that lie beyond unit specification, it may be an indication that unit requires calibra
