Inhaltszusammenfassung zur Seite Nr. 1
QUANTUM GX2360S
25 Watt VHF/FM
Marine Transceiver
Owner's Manual
Oversized alphanumeric LCD, knobs and keys
Large 2.8 inch internal loudspeaker producing louder audio
30 W Loud Hailer with listen back and 4 fog horns, Bells & Whistles
Removable ClearVoice speaker microphone with 16/9 key and channel
selection
Display shows channel names, and repeats GPS information
Capable of connecting 2 optional enhanced RAM+ second station re-
mote microphones
DSC distress call automatically
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS SAFETY/WARNING INFORMATION ........................................................................... 4 FCC RADIO LICENSE INFORMATION ....................................................................... 5 FCC NOTICE ................................................................................................................. 6 GETTING STARTED ..................................................................................................... 7 ABOUT VHF RADIO ........
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS 7 DIGITAL SELECTIVE CALLING .......................................................................... 35 7.1 GENERAL ...................................................................................................... 35 7.2 USCG DSC WATCH.................................................................................... 35 7.2.1 Maritime Mobile Service Identity (MMSI) ............................................ 35 7.2.2 Programming the MMSI ........................
Inhaltszusammenfassung zur Seite Nr. 4
SAFETY / WARNING INFORMATION This radio is restricted to occupational use, work related operations only where the radio operator must have the knowledge to control the exposure conditions of its passengers and bystanders by maintaining the minimum separation dis- tance of 0.6 m (2 feet). Failure to observe these restrictions will result in exceeding the FCC RF expo- sure limits. Antenna Installation: The antenna must be located at least 0.6 m (2 feet) away from passengers in order to comply with
Inhaltszusammenfassung zur Seite Nr. 5
FCC RADIO LICENSE INFORMATION Standard Horizon radios comply with the Federal Communication Commission (FCC) requirements that regulate the Maritime Radio Service. STATION LICENSE An FCC ship station license is no longer required for any vessel traveling in U.S. waters (except Hawaii) which is under 20 meters in length. However, any vessel required to carry a marine radio on an international voyage, carrying a HF single side band radiotelephone or marine satellite terminal is required to have a
Inhaltszusammenfassung zur Seite Nr. 6
FCC NOTICE NOTICE Unauthorized changes or modifications to this equipment may void com- pliance with FCC Rules. Any change or modification must be approved in writing by STANDARD HORIZON. NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful in- terference in a residential installation. This equipment generates, uses and can radiate ra
Inhaltszusammenfassung zur Seite Nr. 7
GETTING STARTED ABOUT VHF RADIO The radio frequencies used in the VHF marine band lie between 156 and 158 MHz with some shore stations available between 161 and 163 MHz. The ma- rine VHF band provides communications over distances that are essentially “line of sight” (VHF signals do not travel well through objects such as buildings, hills or trees). Actual transmission range depends much more on antenna type, gain and height than on the power output of the transmitter. On a fixed mount 25W radio
Inhaltszusammenfassung zur Seite Nr. 8
COAXIAL CABLE VHF antennas are connected to the transceiver by means of a coaxial cable – a shielded transmission line. Coaxial cable is specified by it’s diameter and construction. For runs less than 20 feet, RG-58/U, about 1/4 inch in diameter is a good choice. For runs over 20 feet but less than 50 feet, the larger RG-8X or RG-213/U should be used for cable runs over 50 feet RG-8X should be used. For installa- tion of the connector onto the coaxial cable refer to the figure below. Adapter 1/1
Inhaltszusammenfassung zur Seite Nr. 9
1 GENERAL INFORMATION 1.1 INTRODUCTION The STANDARD HORIZON QUANTUM is a VHF/FM transceiver designed for use in the frequency range of 156.025 to 163.275 MHz. The QUANTUM can be operated from 11 to 16 VDC and has a switchable RF output power of 1 watt or 25 watts. The QUANTUM is capable of RTCM SC101 DSC (Digital Selective Calling) operation and up 2 Enhanced second station RAM+ mic (CMP25 remote-con- trol speaker/microphone with display). The QUANTUM operates on all currently-allocated marine
Inhaltszusammenfassung zur Seite Nr. 10
2 PACKING LIST When the package containing the transceiver is first opened, please check it for the following contents: GX2360S QUANTUM Transceiver Mounting Bracket and attaching hardware Owner’s Manual Quick-Reference Card Power Cord 3 OPTIONS MMB-84 .......................................................................... Flush-Mount Bracket CMP25B/W ................ Remote-Access Microphone (RAM+ Mic, Black/White) CT-100 ................................................ 10-foot Ex
Inhaltszusammenfassung zur Seite Nr. 11
4 INSTALLATION 4.1 LOCATION The radio can be mounted at any angle. Choose a mounting location that: • is far enough from any compass to avoid any deviation in compass read- ing due to the speaker magnet • provides accessibility to the front panel controls • allows connection to a power source and an antenna • has nearby space for installation of a microphone hanger • the antenna must be mounted at least 3 feet from radio Note: To insure the radio does not affect the compass or radios performan
Inhaltszusammenfassung zur Seite Nr. 12
2. Connect the red power wire to a 13.8 VDC ±20% power source. Connect the black power wire to a negative ground. 3. If an optional remote extension speaker is to be used, refer to section 3.3 for connections. 4. It is advisable to have a Certified Marine Technician check the power output and the standing wave ratio of the antenna after installation. 4.3 ACCESSORY CABLE White: External speaker (+) Shield: External speaker (–) Red: PA speaker (+) Shield: PA speaker (–) Blue: NMEA IN (+) from GPS
Inhaltszusammenfassung zur Seite Nr. 13
4.4 CONNECTION OF GPS WITH NMEA OUTPUT Manufacturer/Model Wires QUANTUM Manufacturer/Model Wires QUANTUM Green Green Lowrance Portable Orange Blue STANDARD HORIZON Blue Gray Black (GND) Green Brown Blue Magellan Fixed Mount Gray Blue Furuno GP30, 36 White Blue Black (GND) Green Blue Green Magellan Portable Orange Blue Furuno GP1650, 1850 White Blue Black (GND) Green Black Green Northstar Yellow Blue Garmin Fixed Mounts Blue Blue Black (GND) Green Black (GND) Green Raytheon 420 Yellow Blue Garmi
Inhaltszusammenfassung zur Seite Nr. 14
4.5 CHECKING GPS CONNECTIONS After connections have been made between the QUANTUM and the GPS, a small satellite icon will appear on the top right corner of the LCD display. To see [ ( )] additional GPS information press and hold the H/L NAV key until the QUANTUM shows the Date, Time, SOG and COG. 4.6 CHANGING THE GPS TIME From the Factory the QUANTUM shows GPS satellite time or UTC time. A time offset is needed to show the local time in your area. [ ( )] 1. Press and hold down the CALL/SET ME
Inhaltszusammenfassung zur Seite Nr. 15
4.7 CHANGING COG TO TRUE OR MAGNETIC Allows customizing the NAV data showing GPS Course Over Ground (COG). Factory default is True however following the steps below the COG can be changed to Magnetic. [ ( )] 1. Press and hold down the CALL/SET MENU key until “RADIO SETUP” menu appears. [ ( )] 2. Press the CALL/SET MENU key, then select “TRUE MAG” in the “RADIO SETUP” menu with the CHANNEL selector knob. [ ( )] 3. Press the CALL/SET MENU key. 4. Turn the CHANNEL selector knob to select “MAG- NET
Inhaltszusammenfassung zur Seite Nr. 16
4.8 OPTIONAL MMB-84 FLUSH MOUNT INSTALLATION 1. Make a rectangular template for the flush mount measuring 2-27/32” H x 8-5/64” W (72 x 205 mm). 2. Use the template to mark the location where the rectangular hole is to be cut. Confirm the space behind the dash or panel is deep enough to accom- modate the transceiver (at least 6 inches deep). There should be at least 1/2 inch between the transceiver’s heatsink and any wiring, cables or structures. 3. Cut out the rectangular hole and insert the tr
Inhaltszusammenfassung zur Seite Nr. 17
4.9 OPTIONAL ENHANCED RAM+ SECOND STATION MIC INSTALLATION The QUANTUM is capable of using up to 2 Enhanced RAM+ mics to remotely control the Radio, DSC and PA/Fog functions. In addition the QUANTUM can operate as a full function intercom system. With 2 RAM+ mics connected the QUANTUM or RAM+ mics can selective call each station individually or all at one time. 1. Connect the RAM+ MIC Cable to the RAM MIC CONNECTOR on the rear panel, then tighten the Cable Nut (See Figure 3). 2. Referring to Fi
Inhaltszusammenfassung zur Seite Nr. 18
5 CONTROLS AND INDICATORS NOTE This section defines each control of the transceiver. See Figure 4 for location of controls. For detailed operating instructions refer to chapter 6 of this manual. 5.1 CONTROLS AND CONNECTIONS ( ) POWER SWITCH/VOLUME CONTROL VOL/PWR Turns the transceiver on and off as well as adjusts the audio volume. To turn the transceiver on press and hold this knob until the LCD turns on. To turn it off, press and hold this knob until the LCD turns off. When the power is tur
Inhaltszusammenfassung zur Seite Nr. 19
16/9 WX VOL/PWR A/B QUANTUM GX2360S IC PA/ SQL DW SCAN FOG DISTRESS NAV MENU PULL OPEN CALL H/L MEM SET Figure 4. Controls and Connectors GX2360S Page 19
Inhaltszusammenfassung zur Seite Nr. 20
[ ] WX Key Immediately recalls the previously selected NOAA weather channel from any channel. Secondary use 1. Holding down the [16/9] key while pressing the [WX] key changes the mode from USA to International or Canadian. [ ] [ ] 2. Holding down the WX and SCAN key while turning the power on resets the microprocessor and erases scan channels from memory. This clears the memory and establishes the factory-set defaults. For a list of these defaults, see the section on 6.23 Resetting the Transceiv
