Inhaltszusammenfassung zur Seite Nr. 1
IMPORTANT MANUAL Do Not Throw Away
02478
OPERATOR'S MANUAL
WARNING:
MODEL:
Read this Manu al and follow all Warnings and
Safety Instructions. Fail ure to do so can re sult
in serious in ju ry.
BB185H42LT
LAWN TRACTOR
ALWAYS WEAR EYE PROTECTION DURING OPERATION
Visit our website: www.poulan-pro.com
194992 10.26.04 RD
Printed in U.S.A.
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Do not operate machine without the entire grass catcher, discharge guard, or other safety devices in place and WARNING: In order to prevent ac ci - working. den tal starting when setting up, trans- Slow down before turning. por t ing, ad
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY RULES Safe Operation Practices for Ride-On Mowers III. CHILDREN GENERAL SERVICE Tragic accidents can occur if the operator is not alert to Never operate machine in a closed are. Keep all nuts and bolts tight to be sure the equipment the presence of children. Children are often attracted to the ma chine and the mowing activity. Never assume that is in safe working condition. Never tamper with safety devices. Check their proper children will remain where you last saw the
Inhaltszusammenfassung zur Seite Nr. 4
CONGRATULATIONS on your purchase of a new tractor. PRODUCT SPECIFICATIONS It has been designed, engineered and manu factured to giv e Gasoline Capacity 2.0 Gallons you the best possible dependability and performance. and Type: Unleaded Regular Should you experience any problem you cannot easily rem- Oil Type (API-SG-SL): SAE 30 (above 32°F) edy, please contact your nearest authorized service center/
Inhaltszusammenfassung zur Seite Nr. 5
UNASSEMBLED PARTS Steering Wheel Seat (1) Washer Steering 17/32 x 1-3/16 x 12 Gauge Boot Steering Wheel (1) Knob Insert Steering Steering Extension Wheel Key Shaft Adapter (1) Large Flat Washer (2) Keys (1) Oil Drain Tube Slope Sheet (1) 5/16 Lock Washer (1) Hex Bolt 5/16-18 x 4 5
Inhaltszusammenfassung zur Seite Nr. 6
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY A socket wrench set will make assembly easier. Stan dard INSERT wrench sizes are listed. 5/16 HEX BOLT (1) 3/4" wrench Pliers 5/16 LOCK WASHER (1) 1/2" wr
Inhaltszusammenfassung zur Seite Nr. 7
ASSEMBLY NOTE: You may now roll or drive your tractor off the skid. Follow the ap pro pri ate instruction below to remove the SEAT tractor from the skid. SHOULDER BOLT TO ROLL TRACTOR OFF SKID (See Op- er a tion section for location and function of con trols) Press lift lever plunger and raise attachment lift lever SEAT PAN to its highest po si tion. Release parking brake by de press ing clutch/brake ped al. Place freewheel control in "trans mis sion dis en gaged position
Inhaltszusammenfassung zur Seite Nr. 8
ASSEMBLY CHECK TIRE PRESSURE ✓CHECKLIST The tires on your tractor were overinfl ated at the factory BEFORE YOU OPERATE YOUR NEW TRAC TOR, WE for shipping purposes. Correct tire pressure is important WISH TO ASSURE THAT YOU RECEIVE THE BEST PER- for best cutting performance. FORMANCE AND SATISFACTION FROM THIS QUALITY Reduce tire pressure to PSI shown in “PRODUCT PRODUCT. SPEC I FI CA TIONS” section of this manual. PLEASE REVIEW THE FOLLOWING CHECKLIST: ✓ All assembly instructions hav
Inhaltszusammenfassung zur Seite Nr. 9
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. FAST SLOW REVERSE NEUTRAL HIGH LOW CHOKE IGNITIONSWITCH P ENGINESTART PARKINGBRAKE ENGINEOFF REVERSE ENGINEON PARKINGBRAKE PARKINGBRAKE OPERATION LOCKED UNLOCKED SYSTEM(ROS) OILPRESSURE BATTERY OVERTEMP FUEL REVERSE FORWARD MOWERHEIGHT MOWERLIFT LIGHT 15 15 ATTACHMENT ATTACHMENT SLOPEHAZARDS DANGER,KEEPHANDS KEEPAREACLEAR CLUTCHDISENGAGED CLUTCHENGAGED (SEESAFETYR
Inhaltszusammenfassung zur Seite Nr. 10
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. AT TACHMENT IGNITION ROS "ON" POSITION CLUTCH LEVER SWITCH LIFT LEVER LIGHT SWITCH PLUNGER THROTTLE/CHOKE ATTACHMENT CONTROL LIFT LEVER CLUTCH/BRAKE PEDAL HEIGHT ADJUSTMENT INDICATOR PARKING FREE WHEEL BRAKE CONTROL MOTION CO
Inhaltszusammenfassung zur Seite Nr. 11
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while op- erating your tractor or per forming an y adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY HOW TO USE YOUR TRACTOR POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DIS CHARGED, (DEAD). TO SET PARK
Inhaltszusammenfassung zur Seite Nr. 12
01423 OPERATION TO ADJUST GAUGE WHEELS (See Fig. 6) "ENGAGED" PO SI TION Gauge wheels are properly adjusted when they are slightly ATTACHMENT LIFT LEVER off the ground when mower is at the desired cutting height HIGH PO SI TION in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain LOW conditions. POSITION NOTE:Adjust gauge wheels with tractor on a fl at level DEFLECTOR surface. SHIELD Adjust mower to desired cutting height (
Inhaltszusammenfassung zur Seite Nr. 13
OPERATION Choose the slowest speed before starting up or down Remove oil fi ll cap/dipstick and wipe clean, reinsert the hills. dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until Avoid stopping or changing speed on hills. “FULL” mark on dipstick is reached. Do not overfi ll. If slowing is necessary, move throttle control lever to For cold weather operation you should change oil for slower position. easier s
Inhaltszusammenfassung zur Seite Nr. 14
OPERATION WARM WEATHER STARTING (50° F and above) MOWING TIPS When engine starts, move the throttle control to the fast position. Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the The attachments and ground drive can now be used. If Service and Adjustments section of this manual. the engine does not accept the load, restart the engine The left hand side of mower should be used for trim- and allow it to warm up for one mi
Inhaltszusammenfassung zur Seite Nr. 15
maint_sch-tractore.ROS.e MAINTENANCE MAINTENANCESCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES Check Brake Operation Check Tire Pressure Check Operator Presence and ROS Systems T R Check for Loose Fasteners 5 A Sharpen/Replace Mower Blades 3 C Lubrication Chart T Check Battery Level 4 0 Clean Battery and Terminals R Check Transaxle Cooling Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (without oil filter) 1,2 E Clean Air Filt
Inhaltszusammenfassung zur Seite Nr. 16
MAINTENANCE BLADE CARE TRACTOR For best results mower blades must be kept sharp. Re place Always observe safety rules when per forming an y main- bent or damaged blades. te nance. BRAKE OPERATION CAUTION: Use only a replacement blade approved by the manufacturer of your If tractor requires more than fi ve (5) feet to stop at highest tractor. Using a blade not approved speed in high est gear on a level, dry concrete or paved by the manufacturer of your tractor is surface, then brake must
Inhaltszusammenfassung zur Seite Nr. 17
MAINTENANCE Slide blade on to an unthreaded portion of the steel bolt TRANSAXLE PUMP FLUID or pin and hold the bolt or pin parallel with the ground. The transaxle was sealed at the factory and fl uid main te - If blade is balanced, it should remain in a horizontal nance is not required for the life of the transaxle. Should position. If either end of the blade moves downward, the transaxle ever leak or require servicing, contact your sharpen the heavy end until the blade is balanced
Inhaltszusammenfassung zur Seite Nr. 18
MAINTENANCE Unlock drain valve by pushing inward and turning MUFFLER coun ter clock wise. Inspect and replace corroded muffl er and spark arrester To open, pull out on the drain valve. (if equipped) as it could create a fi re hazard and/or dam- After oil has drained completely, close and lock the age. drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. SPARK PLUGS Remove the drain tube and replace the cap onto to the
Inhaltszusammenfassung zur Seite Nr. 19
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: Depress clutch/brake pedal fully and set parking brake. Place motion control lever in neutral (N) position. Place attachment clutch in “DISENGAGED” position. Turn ignition key to “STOP” and remove key. Make sure the blades and all moving parts have completely stopped. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug
Inhaltszusammenfassung zur Seite Nr. 20
SERVICE AND ADJUSTMENTS SIDE-TO-SIDE ADJUSTMENT (See Figs. 16 and 17) Raise mower to its highest position. At the midpoint of both sides of mower, measure height MANDREL from bot tom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other. "D" "D" If adjustment is necessary, make adjustment on one side of mower only. FIG. 18 To raise one side of mower, tighten lift link ad just ment nut on that side. BOTH FRONT LINKS
