Inhaltszusammenfassung zur Seite Nr. 1
Owner’s Instruction and
Safety Manual
pet trailer
™
Burley Tail Wagon
™
Burley Tail Wagon model shown
(Stroller Kit and Kickstand are Sold Separately)
Stroll Bike Ski Jog
Inhaltszusammenfassung zur Seite Nr. 2
Contents Owner’s Instruction 3 Introduction and Safety Manual 3 SafetyGuidelines ™ Burley Tail Wagon 3 Parts Bag Contents 3 Tools Required 4 Installing Light 4 InstallingW heel Guard Tube 4 Opening Your Trailer 5 AttachingW heels 5 Attaching Handle 5 InstallingT ow Bar 6 Attaching Cover 6 AttachingT ailgate 7 RemovingFloor 8 Installing Safety Flag 8 Using ParkingBrake 9 Hitching Trailer to Your Bicycle 10 Safety Check
Inhaltszusammenfassung zur Seite Nr. 3
9. Only use factory-supplies wheels, with the tires inflated Congratulations! to the pressure recommended on tire sidewall. Check Your Burley® trailer is the leading choice of refined bicycle the tires before each use. Do not use higher-pressure or trailer owners worldwide. Every effort has been made to knobby tires. ensure your purchase is a top-quality, thoroughly-tested 10. Clamp the hitch securely to the bicycle frame, and check design, ready to provide many years and miles of happy,
Inhaltszusammenfassung zur Seite Nr. 4
Installing Light Bracket 1. Slide clip on light into bracket channel. 2. Mount light/bracket on rear side frame tube, on side closest to traffic. Tighten bracket screw. PHOTO 1 Note: Make sure light switch isa ccessible. PHOTO 1 Rear Side of Main Frame Tube Light Switch PHOTO 1: Light mounted on rear side of main frame tube Installing Wheel Guard Tube 1. With wheel guard tube ends facing toward the wheels (away from the trailer front), match holes in wheel guard Trailer Front tube
Inhaltszusammenfassung zur Seite Nr. 5
Attaching Wheels 1. Insert wheel axle assembly completely into trailer axle. FIGURE 3 2. Close quick release lever, with lever aimed at trailer rear. A properly adjusted quick release lever should leave an imprint on your palm when the lever is rotated to the closed position. FIGURE 4 3. Verify that tires are inflated to pressure marked on tire side wall. Trailer 4. To remove wheel from trailer axle, open quick release lever. Rear Top View Top View WARNING FIGURE 3: Quick re
Inhaltszusammenfassung zur Seite Nr. 6
Attaching Cover 1. On trailer front, join buckle sections on cover corners to buckle sections below side windows. PHOTO 5 2. On trailer rear, hook O-rings on cover rear over side Side Window knobs. PHOTO 6 3. At top of frame, fasten cover snaps to frame. Buckle PHOTO 5: Trailer front side O-ring Side Knob PHOTO 6: Trailer rear side Attaching Tailgate Note: If your pet is prone to making unplanned exits, OPTION 1 is the more secure attachment. OPTION 1: Tailgate fastened over cover Join
Inhaltszusammenfassung zur Seite Nr. 7
Removing Floor Trailer Front 1. To remove for cleaning, lift floor at inside front and pull out of trailer. PHOTO 9 2. Remove fabric covering from floor base. 3. To install floor, insert rear of floor under nuts in trailer rear and under D-rings on trailer sides. In front corners, snap floor under front nuts. PHOTO 10 PHOTO 9 Trailer Front Front Nut Side D-ring PHOTO 10 B U R L E Y T A I L W A G O N O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L 7
Inhaltszusammenfassung zur Seite Nr. 8
Installing Safety Flag Join pole sections together. On trailer’s left side, insert flag pole into hole in handle receiver by wheel axle. IMPORTANT DO NOT USE TRAILER WITHOUT SAFETY FLAG. Using Parking Brake Engage parking brake by pushing handle to the right. Exercise caution when disengaging brake, as it may spring to the Brake Handle Engaged left. PHOTO 11 Brake PHOTO 11 8 B U R L E Y T A I L W A G O N O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L
Inhaltszusammenfassung zur Seite Nr. 9
Hitching Trailer to Your Bicycle Note: The Burley Forged Standard Hitch isu sed for bicycles with either nutted axles FIGURE 5 or Hitch quick release assemblies FIGURES 6 & 7 1. Remove axle nut or rear quick release lever Nut assembly from bike. 2. Match hole on flat side of hitch upper arm to left (non-chain ring side) rear dropout hole, and place hitch flat against the dropout. 3. Loosely reassemble axle nut or quick release assembly through hitch, dropout and wheel
Inhaltszusammenfassung zur Seite Nr. 10
Safety Checklists 2009 Tail Wagon Replacement Parts and Diagram Tail Check Before Each Ride: Diagram Wagon Description Warranty ✓ Wheels tightly and securely attached # Part # ✓ Tires inflated to recommended pressure on tire side wall 1 960041 Forged Standard Hitch 5 years ✓ Hitch properly secured with safety strap in place 2 960009 Safety Flag 1 year 3 250144 Handle Bar Assembly 5 years ✓ Tow bar locked securely in place 250294 Side Panel/Front (NOT SHOWN) 1 year ✓ Bicycle safety check, espec
Inhaltszusammenfassung zur Seite Nr. 11
B U R L E Y T A I L W A G O N O W N E R ’ S I N S T R U C T I O N A N D S A F E T Y M A N U A L 11
Inhaltszusammenfassung zur Seite Nr. 12
Burley Trailer Limited Warranty Burley trailers are warranted against defects in materials and workmanship under normal use and service. Burley will repair or replace parts it determines to be defective as follows: fabric parts for one year, plastic parts for three years and durable frame parts for five years. The Burley trailer owner must present the trailer for repair at place of purchase, with an original sales receipt or similar proof of purchase. This warranty applies only to the origin
