Inhaltszusammenfassung zur Seite Nr. 1
Safety Instructions & Operator’s Manual for
26” STEEL DECK
HIGH WHEEL
WALK MOWER
SERIES 0
MODEL
HWPS26700BV
MODEL NUMBER EXPLANATION
HW P S 26 70 0 B V
MODEL DESIGNATION ENGINE OPTIONS
CUTTING WIDTH ENGINE TYPE
ENGINE HP SERIES DESIGNATION
HW - High Wheel Model 26 - 26” Cutting Deck 0 - Series Designation B – Briggs Engine
P - Self-Propelled Machine 70 – 7.0 HP Engine V - Over Head Valve
S - Swivel Front Wheels
Thank you for buying a SN
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETY INSTRUCTIONS SAFE HANDLING OF GASOLINE OPERATION (Continued From Previous Page) (Continued From Previous Column) 3. DO NOT remove fuel cap or add fuel with the engine 11. STOP engine and wait until the blade comes to running. Allow the engine to cool before refueling. complete STOP before removing grass bag and/or 4. DO NOT refuel the machine indoors. clearing grass. 5. DO NOT store the machine or fuel container inside 12. DO NOT operate mower without the entire grass
Inhaltszusammenfassung zur Seite Nr. 4
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ........................................................................ 2-3 TABLE OF CONTENTS ..................................................................................................... 4 SECTION 1 - FAMILIARIZATION ...................................................................................... 5 SECTION 2 - OPERATING INSTRUCTIONS ................................................................. 6-9 Pre-start Checklist....
Inhaltszusammenfassung zur Seite Nr. 5
Section 1 - FAMILIARIZATION BLADE CONTROL ENGINE SPEED CONTROL WHEEL DRIVE CONTROL GROUND SPEED CONTROL FUEL TANK ENGINE OIL DIP STICK SWIVEL WHEEL LOCK CONTROL REAR HEIGHT ADJUSTMENT LEVER DEFLECTOR FIGURE 1.1 1.1 INTRODUCTION 1.2 NOMENCLATURE This manual has been prepared for the operators of the The nomenclature drawing above, Figure 1.1, shows the SNAPPER WALK BEHIND MOWERS. Its purpose, essenti
Inhaltszusammenfassung zur Seite Nr. 6
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST WARNING Familiarize yourself with all controls, instructions and DO NOT leave machine with engine running. warnings on this machine before attempting to operate it. DO NOT place your hands or feet near the blade Know how to stop the wheel drive, stop the blade and stop while the engine is running! the engine before starting the engine. Make the following DO NOT attempt any adjustments, maintenance or c
Inhaltszusammenfassung zur Seite Nr. 7
Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION WHEEL GROUND SPEED 2.2.1. TO START ENGINE DRIVE CONTROL CONTROL (Continued From Previous Page) 3. Stabilize the machine by placing your left foot on the left rear wheel. Machine should be on flat surface where footing is secure. 4. Pull rope start handle to crank engine. Guide rope back into engine. DO NOT let it snap back. 5. After engine starts, move engine speed control away from the choke position to the “Fast” (Ra
Inhaltszusammenfassung zur Seite Nr. 8
Section 2 - OPERATING INSTRUCTIONS CUTTING HEIGHT REAR WARNING ADJUSTING LATCH DO NOT attempt any adjustments, maintenance or MOVE service with the engine or blade running. STOP OUTWARD MOVE DOWN OR blade. STOP engine. Remove spark plug wire from UP TO DESIRED spark plug and secure wire away from spark plug. CUTTING HEIGHT Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. 2.4 HANDLE HEIGHT ADJUSTMENT The height
Inhaltszusammenfassung zur Seite Nr. 9
Section 2 - OPERATING INSTRUCTIONS 2.7 RECYCLING OPERATION (OPTIONAL) WARNING Recycling operation requires an optional accessory. Cutting on slopes is dangerous. Exercise extreme Contact your local Snapper dealer for details. caution. Loss of footing can result in serious injury. Cut across slopes - never up and down. Practice on NOTE: For best recycling results, cut up to a maximum slopes with blade off. of 1/3 of grass blade length and recycle ONLY when grass is dry. 2.6 SWIV
Inhaltszusammenfassung zur Seite Nr. 10
Section 3 - MAINTENANCE 3.1 INTRODUCTION 3.2.2. SERVICE ENGINE To retain the quality of the mower, use genuine Service engine air cleaner. Refer to engine owner’s SNAPPER replacement parts only. Contact a local manual for proper air filter specification and SNAPPER dealer for parts and service assistance. maintenance procedure. For the correct part or information for a particular mower, always mention model and serial number. 3.2.3. GREASE FRONT CASTER BUSHINGS Grease front caster b
Inhaltszusammenfassung zur Seite Nr. 11
Section 3 - MAINTENANCE 3.3 SERVICE – EVERY 25 OPERATING HOURS WARNING Perform all service described in Section “SERVICE – DO NOT attempt any adjustments, maintenance or AFTER FIRST 5 HOURS", and all maintenance required service with the engine or blade running. STOP in “Service Schedule”. blade. STOP engine. Remove spark plug wire from spark plug and secure wire away from spark plug. 3.4 SERVICE - ANNUALLY Engine and components can be extremely hot. Avoid Perform all maintenance as
Inhaltszusammenfassung zur Seite Nr. 12
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury. REMOVE B
Inhaltszusammenfassung zur Seite Nr. 13
Section 4 - REPAIR & ADJUSTMENTS WHEEL DRIVE WARNING CONTROL CABLE DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades THERE SHOULD BE SOME are ex
Inhaltszusammenfassung zur Seite Nr. 14
Section 4 - REPAIR & ADJUSTMENTS WARNING TRANSFER ROD DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. GROUND SPEED 4.3.3. DRIVEN DISC ADJUSTMENT CONTROL ROD The driven disc position is set at the factory and should not
Inhaltszusammenfassung zur Seite Nr. 15
Section 4 - REPAIR & ADJUSTMENTS 4.3.5. Replacing Bearing In Driven Disc WARNING If the driven disc bearing fails, remove the driven DO NOT attempt any adjustments, maintenance or disc assembly and replace bearing as follows: service with the engine or blade running. STOP 1. Remove snap ring. blade. STOP engine. Remove spark plug wire from 2. Slide the hub assembly out of the bearing. spark plug and secure wire away from spark plug. 3. Remove the four screws. Engine and components
Inhaltszusammenfassung zur Seite Nr. 16
Section 4 - REPAIR & ADJUSTMENTS 4.4. WHEEL DRIVE BELT SERVICE WARNING On this machine, the engine belt transmits power from DO NOT attempt any adjustments, maintenance or the engine to the drive disc. The drive disc powers the service with the engine or blade running. STOP poly-v belt, which engages the transmission that blade. STOP engine. Remove spark plug wire from powers the rear wheels. Should these belts become worn, they could cause slippage. The condition of the spark plug a
Inhaltszusammenfassung zur Seite Nr. 17
Section 4 - REPAIR & ADJUSTMENTS 3. With engine off, engage blade control. The length WARNING of the spring should increase by 1/4" to 3/8" for DO NOT attempt any adjustments, maintenance or proper belt tension. service with the engine or blade running. STOP 4. To obtain proper tension, turn the thumb screw blade. STOP engine. Remove spark plug wire from located on the upper left handle until the spring spark plug and secure wire away from spark plug. extension is 1/4" to 3/8". Engin
Inhaltszusammenfassung zur Seite Nr. 18
Section 4 - REPAIR & ADJUSTMENTS WARNING DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool. WARNING DO NOT use machine if blade brake does not function properly. 4.6 BLADE BRAKE ADJUSTMENT The b
Inhaltszusammenfassung zur Seite Nr. 19
TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTIVE ACTION Engine Will Not Start 1. Fuel tank empty or fuel valve OFF. 1. Fill fuel tank with fresh fuel. Turn valve ON. Using Recoil Starter 2. Engine needs choking. 2. Move choke control to “CHOKE” position. 3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug. 4. Engine speed control in STOP position. 4. Move control to choke or fast position. Engine Stalls or Stops 1. Choke control in the “CHOKE” position. 1. Move
Inhaltszusammenfassung zur Seite Nr. 20
SERVICE SCHEDULE ITEM SERVICE PERFORMED REF. EACH 5 25 50 100 EACH USE HRS HRS HRS HRS SEASON Engine Oil Check Oil Level Engine Manual X Initial Oil Change Page 10 X Periodic Oil Change Page 10 X* Oil Filter Replace with Oil Change Engine Manual X* Clean Sponge Element Engine Manual Air Pre-Cleaner X** Air Cleaner Clean or Replace Engine Manual. X** Spark Plug Replace Engine Manual. X Clean Shroud & Fins Engine Manual Engine Cooling X**
