Bedienungsanleitung GE Monogram Wine Reserve and Beverage Center

Inhaltszusammenfassung zur Seite Nr. 1

Installation
Instructions
If you have questions, call 800.626.2000 or visit our website at: www.monogram.com
Wine Chiller,
Wine Reserve
and
Beverage Center
Design Guide
With Installation Instructions

Inhaltszusammenfassung zur Seite Nr. 2

Safety Information BEFORE YOU BEGIN: WARNINGS: Read these instructions completely and carefully. • Use this appliance only for its intended purpose. • Immediately repair or replace electrical service IMPORTANT – Save these instructions cords that become frayed or damaged. for local inspector’s use. • Unplug the unit before cleaning or making repairs. • Repairs should be made by a qualified service IMPORTANT – Observe all governing technician. codes and ordinances. Note to Installer – Be sure to

Inhaltszusammenfassung zur Seite Nr. 3

Design Guide THE INSTALLATION SPACE PRODUCT CLEARANCES The wine chiller, wine reserve and beverage center is factory set for a 110° door swing. Locate When installed in a corner: Outlet • Allow 4″ min. clearance on the hinge side for the 10-1/2" 90° door swing and to allow racks to slide out. 24" • Allow 10″ minimum clearance on the hinge side 34-1/2"-35" 9" Max. for a full 110° door swing. 1-1/2" 90° Door Swing 23-3/4" 23-3/4" Min. 10" Minimum to Wall 21-5/8" NOTE: 34-1/2" Handle and handl

Inhaltszusammenfassung zur Seite Nr. 4

Installation Instructions TOOLS REQUIRED STAINING WOOD DRAWER FRONTS • #2 Phillips screwdriver The drawer fronts are unfinished cherry wood. • Adjustable wrench During use, oil from hands may accumulate and stain the wood. • The drawer fronts may be stained and sealed to PARTS SUPPLIED match adjacent cabinetry. The tinted glass will • Monogram nameplate make the stained wood appear darker. A true color • Hardware for changing door swing match can be seen only when the door is opened. • Optional

Inhaltszusammenfassung zur Seite Nr. 5

Installation Instructions STEP 2 REVERSE DOOR SWING SKIP THIS STEP IF DOOR SWING SUITS THE INSTALLATION Install 3 Hinge Parts Included: Screws • Top left case hinge Remove • Bottom left case hinge Top Hinge • Left and right side decorative hinge cover • Decorative hinge screw hole cover ® • Torx driver bit Hinge Tools Required: Pin and • Phillips screwdriver Bracket • Electric drill Door Stop and Cam Riser Remove the door: • Flatten the shipping carton to use as a pad. • Remove the 2 screws an

Inhaltszusammenfassung zur Seite Nr. 6

Installation Instructions STEP 3 LEVEL STEP 5 SLIDE PRODUCT INTO • Use an adjustable wrench to turn the leveling legs THE CUTOUT and raise or lower the product. • Carefully, slide the unit into the opening. • Adjust carefully; the product should be level and Be careful not to entangle power cord. plumb with cabinetry, and should align with adjacent • Make certain that the door protrudes 1″ beyond toekick height. the surrounding cabinets. • Check again to be sure the unit is level. STEP 6 INS

Inhaltszusammenfassung zur Seite Nr. 7

7

Inhaltszusammenfassung zur Seite Nr. 8

TEMPLATE FOR NAMEPLATE LOCATION Cut on Dotted Line Upper Left Upper Right Top of Glass Door Corner of Corner of Glass if Hinge Glass if Hinge Top of Badge is on Left is on Right Door Frame Side Door Frame Side DOOR NAMEPLATE LOCATION To position nameplate: • Cut template along dotted line. • Hold or tape template behind glass door so that it is visible from the front side. • Remove backing from nameplate. • Place nameplate onto front side of door, matching illustration on the template. IMPORTANT