Bedienungsanleitung MTD REVOLUTION OEM-190-626

Inhaltszusammenfassung zur Seite Nr. 1

Operator’s Manual
Twin Rear Bagger
™
For Revolution and ZTT Model Lawn Tractors
Models
OEM-190-625 (for 42-inch decks)
OEM-190-626 (for 46-inch decks)
MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722
770-10442.fm
FORM NO.
PRINTED IN U.S.A.
(8/2000)

Inhaltszusammenfassung zur Seite Nr. 2

FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new twin bagger grass collector. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Before you start assembling your new equipment, please locate the model plate on the equipment and copy the information from it in the space provided below. The information on the model plate is very important if you need help from our Customer Support Department o

Inhaltszusammenfassung zur Seite Nr. 3

SECTION 1: TO THE OWNER ™ Model 625 and Model 626 Twin Rear Bagger Kits are grass collection systems designed for use on Revolution and ZTT Model Lawn Tractors equipped either a 42-inch cutting deck (Model 625) or a 46-inch cutting deck (Model 626) ™ only. It will NOT fit on any other tractor, regardless of the tractor’s FastAttach compatibility. The instructions in this manual are divided into sections. Carefully read all sections and study the illustrations to ensure proper installation an

Inhaltszusammenfassung zur Seite Nr. 4

SECTION 3: ATTACHING THE GRASS COLLECTOR WARNING: Before attempting to install the grass collector, move the machine to flat, level ground, disengage PTO, move control handles into neutral position, set parking brake, stop engine and remove key to prevent unintended starting. Support Tube Rests Here Insert Support Tube Here Bracket Assembly Clevis Pin Hairpin Clip Shoulder Bolt Figure 3 3. Attach the grass bags using the slots as shown in Mounting the Bracket Assembly Figure 4. 1. To ease the

Inhaltszusammenfassung zur Seite Nr. 5

Remove the blades from your tractor’s cutting deck as Hex Flange Nut follows. Wood Block NOTE: Do NOT perform the following steps on tractor’s equipped with a 42-inch deck. 1. Remove the cutting deck from beneath the tractor, (refer to Deck Removal in the MAINTENANCE section of your tractor’s Operator’s Manual for detailed instructions) then gently flip the deck over to expose its underside. 2. Place a block of wood between the center deck housing baffle and the cutting blade to act as a

Inhaltszusammenfassung zur Seite Nr. 6

Models 625 & 626 5 1 28 2 24 14 4 5 10 5 14 3 17 22 24 24 17 26 17 7 8 22 9 30 24 9 24 9 24 27 9 6 13 32 11 12 21 25 20 17 19 23 29 31 37 18 15 35 16 33 36 34 6

Inhaltszusammenfassung zur Seite Nr. 7

Models 625 & 626 REF. NO. PART NO. DESCRIPTION 1 16847A Screen Assembly 2 16596 Hinge Bracket Assembly 3 731-0821A Grass Catcher Cover (Model 625) 731-1417 Grass Catcher Cover (Model 626) 4 731-0824A Plastic Plate, 1/8 x 5.6 sq. 5 726-0258 Zip Twist Fastener 6 723-0412 Tube Seal (Model 625) 723-0413 Tube Seal (Model 626) 7 712-0147 U-Type Speed Nut, #10-24 8 710-0473 Screw, #10-24 x .5 9 710-0599 Hex Screw, 1/4-20 x .5 (Model 625) 710-0896 Hex Screw, 1/4-14 x ..625 (Model 626) 10 16594A Cover As

Inhaltszusammenfassung zur Seite Nr. 8

MANUFACTURER’S LIMITED WARRANTY c. Routine maintenance items such as lubricants, filters, The limited warranty set forth below is given by MTD blade sharpening and tune-ups, or adjustments such PRODUCTS INC (“MTD”) with respect to new merchandise as brake adjustments, clutch adjustments or deck purchased and used in the United States, its possessions adjustments; and normal deterioration of the exterior and territories. finish due to use or exposure. d.MTD does not extend any warranty for produc