Inhaltszusammenfassung zur Seite Nr. 1
M11577
Operator's Manual
532 42 27-27 Rev. 2
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • Do not operate the machine while under the influence WARNING: In order to prevent ac ci den tal of alcohol or drugs. starting when setting up, trans port ing, • Watch for traffic when operating near or crossing ad just ing or making repairs, al wa
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY RULES Safe Operation Practices for Ride-On Mowers GENERAL SERVICE III. CHILDREN • Never operate machine in a closed area. Tragic accidents can occur if the operator is not alert to • Keep all nuts and bolts tight to be sure the equipment the presence of children. Children are often attracted to is in safe working condition. the ma chine and the mowing activity. Never assume that • Never tamper with safety devices. Check their proper children will remain where you last saw them. ope
Inhaltszusammenfassung zur Seite Nr. 4
CONGRATULATIONS on your purchase of a new tractor. It has been designed, engineered and manu fac tured to give PRODUCT SPECIFICATIONS you the best possible dependability and performance. Should you experience any problem you cannot easily rem- GASOLINE CAPACITY 1.5 GALLONS edy, please contact your nearest authorized service center/ AND TYPE: UNLEADED REGULAR department. We have com pe tent, well-trained tech ni cians and the proper tools to ser vice or repair this tractor. OIL TYPE (API: SF-S
Inhaltszusammenfassung zur Seite Nr. 5
UNASSEMBLED PARTS Steering Wheel (1) Lock Washer Steering (1) Large Wheel Insert Flat Washer Steering Wheel (1) Hex Bolt Steering Steering Wheel Extension Adapter Shaft Steering Boot Seat (1) Washer (1) Knob (1) Seat Slope Sheet (1) Oil Drain Tube For Future Use Key(s) 5
Inhaltszusammenfassung zur Seite Nr. 6
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TO INSTALL STEERING WHEEL (See Fig. 2) TOOLS REQUIRED FOR ASSEMBLY ASSEMBLE EXTENSION SHAFT AND BOOT A socket wrench set will make assembly easier. Stan dard wrench sizes are listed. •
Inhaltszusammenfassung zur Seite Nr. 7
ASSEMBLY INSTALL SEAT (See Fig. 3) CHECK TIRE PRESSURE Adjust seat before tightening adjustment knob. The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important • Remove adjustment knob and flat washer securing for best cutting performance. seat to cardboard packing and set aside for assembly • Reduce tire pressure to PSI shown on tires. of seat to tractor. • Pivot seat upward and remove from the cardboard pack- CHECK DECK LEVELNESS i
Inhaltszusammenfassung zur Seite Nr. 8
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. FAST SLOW REVERSE NEUTRAL HIGH LOW CHOKE IGNITION SWITCH REVERSE ENGINE ON ENGINE START PARKING BRAKE MOWER HEIGHT MOWER LIFT ENGINE OFF OPERATION SYSTEM (ROS) CLUTCH/BRAKE LIGHTS ON FUEL BATTERY REVERSE FORWARD CRUISE CONTROL PEDAL 15 15 ATTACHMENT ATTACHMENT DANGER, KEEP HANDS KEEP AREA CLEAR SLOPE HAZARDS CLUTCH DISENGAGED CLUTCH ENGAGED AND FEET AWAY (SEE SAFET
Inhaltszusammenfassung zur Seite Nr. 9
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. E G D B H F A C J Fig. 4 Our tractors conform to the applicable safety standards of the American National Standards Institute. (A) ATTACHMENT LIFT LEVER - Used to raise, lower, (E) ATTACHMENT CLUTCH LEVER - Used to engage the and ad
Inhaltszusammenfassung zur Seite Nr. 10
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. ENGINE - HOW TO USE YOUR TRACTOR • Move throttle control (D) between half and full speed TO SET PARKING BRAKE (See Fig. 5) (fast) position. Your tractor is equip
Inhaltszusammenfassung zur Seite Nr. 11
OPERATION TO OPERATE MOWER TO MOVE FORWARD AND BACKWARD (See Fig. 8) Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with The direction and speed of movement is controlled by the the engine running and the attachment clutch engaged will gearshift lever (J). shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on r
Inhaltszusammenfassung zur Seite Nr. 12
OPERATION ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quan ti ties that can be used within 30 days to assure fuel freshness. ROS "ON" ENGINE "ON" POSITION POSITION (NORMAL OPERATING) CAUTION: Wipe off any spilled oil or Fig. 11 fuel. Do not s
Inhaltszusammenfassung zur Seite Nr. 13
OPERATION COLD WEATHER STARTING (10° C and below) • When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the tem per a ture. • The attachments can also be used during the engine warm-up period. NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 ° F) the ca
Inhaltszusammenfassung zur Seite Nr. 14
MAINTENANCE BEFORE EVERY EVERY EVERY EVERY EVERY BEFORE MAINTENANCE EACH 8 25 50 100 SEASON STORAGE SCHEDULE USE HOURS HOURS HOURS HOURS Check Brake Operation Check Tire Pressure T Check Operator Presence & ROS Systems R Check for Loose Fasteners A Check/Replace Mower Blades 3 C T Lubrication Chart 0 Check Battery Level 4 R Clean Battery and Terminals Clean Debris Off Steering Plate 5 Check Transaxle Cooling Check Mower Levelness Check V-Belts Check Engine Oil Level Change Engine Oil (with oil
Inhaltszusammenfassung zur Seite Nr. 15
MAINTENANCE BLADE CARE TRACTOR For best results, mower blade must be kept sharp. Re place Always observe safety rules when per form ing any bent or damaged blade. main te nance. CAUTION: Use only a replacement blade ap- BRAKE OPERATION proved by the manufacturer of your tractor. If tractor requires more than five (5) feet to stop at highest Using a blade not approved by the manu- speed in high est gear on a level, dry concrete or paved facturer of your tractor is hazardous, could surface,
Inhaltszusammenfassung zur Seite Nr. 16
MAINTENANCE V-BELTS TO CHANGE ENGINE OIL (See Figs. 15 & 16) Determine temperature range expected before oil change. Check V-belts for deterioration and wear after 100 hours All oil must meet API service classification SG-SL. of operation and replace if necessary. The belts are not ad just able. Re place belts if they begin to slip from wear. • Be sure tractor is on level surface. • Oil will drain more freely when warm. TRANSAXLE MAINTENANCE • Catch oil in a suitable container. Keep transaxle
Inhaltszusammenfassung zur Seite Nr. 17
00667 MAINTENANCE ENGINE COOLING SYSTEM (See Fig. 17) CLEANING • Clean engine, battery, seat, finish, etc. of all foreign Debris may clog the engine's air cooling system. Remove matter. blower housing and clean the area shown to prevent over- heating and engine damage. • Clean debris from steering plate. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of drive. AIR SCREEN CLEAN OUT CHAFF AND DEBRIS CAUTION: Avoid all pinch points and movable parts (See Fi
Inhaltszusammenfassung zur Seite Nr. 18
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SE RI OUS IN JU RY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift lever in neutral position. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. IMPORTANT: IF AN AT
Inhaltszusammenfassung zur Seite Nr. 19
SERVICE AND ADJUSTMENTS • ATTACH MOWER SIDE SUSPENSION ARMS (A) TO • Insert end of link (E) into hole in front mower bracket CHASSIS - Position hole in arm over pin (B) on outside and secure with washer and retainer spring (J). of tractor chassis and secure with retainer spring. • Hook end of clutch cable spring (Q) into hole in idler • Repeat on opposite side of tractor. arm (R). E A J F B H FIG. 20 FIG. 22 • ATTACH REAR LIFT LINKS (C) - Lift rear corner of • Push clutch cable housing guide
Inhaltszusammenfassung zur Seite Nr. 20
SERVICE AND ADJUSTMENTS • If adjustment is necessary, see step in Visual Adjust- TO LEVEL MOWER ment instructions above. Make sure tires are properly inflated to the PSI shown on • Recheck measurements, adjust if necessary until both tires. If tires are over or under inflated, it may affect the sides are equal. appearance of your lawn and lead you to think the mower is not adjusted properly. FRONT-TO-BACK ADJUSTMENT (See Figs. 27 & 28) VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 25) IMPORTANT:
