Inhaltszusammenfassung zur Seite Nr. 1
PO Box 1200
305 Commerce Drive
Winfield, Alabama 35594
FLEX HITCH
ROTARY MOWER
OPERATION AND PARTS
www.kingkutter.com
Part No 999993
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
TO THE PURCHASER This manual contains valuable information about your new King Kutter Mower. It has been carefully prepared to give you helpful suggestions for operating, adjusting, servicing and ordering repair parts. Keep this manual in a convenient place for quick and easy reference. Study it carefully. You have purchased a de- pendable and sturdy mower, but only by proper care and op- eration can you expect to receive the service and long life de- signed and built into it. S
Inhaltszusammenfassung zur Seite Nr. 4
It is the purchaser and/or operator’s responsibility to…. Read and understand the information contained in this manual. Operate, lubricate, assemble and maintain the equip- ment in accordance with all instructions and safety procedures in this manual. Inspect the equipment and replace or repair any parts that are damaged or worn which under continued op- eration would cause damage, wear to other parts, or cause a safety hazard. Return the equipment or parts to the authori
Inhaltszusammenfassung zur Seite Nr. 5
CONTENTS ITEM PAGE Safety ........................................................................ 6 Assembly Instructions ................................................ 8 Before Putting Into Service ....................................... 11 Safety Training ......................................................... 12 Operational Safety ................................................... 14 Transportation Safety .............................................. 16 Attaching To Tractor .
Inhaltszusammenfassung zur Seite Nr. 6
SAFETY READ AND FOLLOW THE INSTRUCTIONS IN THIS MANUAL AND ESPECIALLY IN THE SAFETY SECTION. FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY OR DEATH. TAKE NOTE! THIS SAFETY ALERT SYM- BOL FOUND THROUGHOUT THIS MANUAL IS USED TO CALL YOUR ATTENTION TO THIS SYMBOL MEANS INSTRUCTIONS INVOLVING YOUR PER- ATTENTION! SONAL SAFETY AND THE SAFETY OF BECOME ALERT! YOUR SAFTEY IS INVOLVED OTHERS. SIGNAL WORDS: The signal words DANGER, WARNING and CAUTION are used with the safety messag
Inhaltszusammenfassung zur Seite Nr. 7
EQUIPMENT SAFETY GUIDELINES Safety of the operator and by standards is one of the main concerns in designing and devel- oping a mower. However, every year accidents occur which could have been avoided by a few seconds of thought and a more careful approach to handling equipment. You, the opera- tor, can avoid many accidents by observing the following precautions and insist those working with you, or for you, follow them. In order to provide a better view, certain photographs or i
Inhaltszusammenfassung zur Seite Nr. 8
FLEX HITCH ROTARY MOWER ASSEMBLY INSTRUCTIONS STEP 1 Place rotary mower on a flat, level surface. (See Figure A) STEP 2 Remove the wired on PTO shaft. Remove the(2) bolts that are on the lift arm lugs, and the bolt holding the pivot shield on. (See arrows Figure C) Place the (3)bolts, the pivot shield and the PTO shaft to the side (See Figure B) you will replace these items as you put the unit together for service. STEP 3 Rotate arms up to a standing position (See Figure D) and re
Inhaltszusammenfassung zur Seite Nr. 9
Figure A Figure B Figure D Figure C 9
Inhaltszusammenfassung zur Seite Nr. 10
Figure E Figure F Figure G Figure H Figure I 10
Inhaltszusammenfassung zur Seite Nr. 11
BEFORE PUTTING ROTARY MOWER INTO SERVICE (IMPORTANT-INSTRUCTIONS PRIOR TO START UP) SHIPPED WITH OIL IN GEARBOX SHIPPED WITHOUT GREASE IN GREASE FITTINGS. UNIT MUST BE SERVICED BEFORE USING. • Use Multi-Purpose Gear Oil (I.E. S.A.E. 80w/90 or S.A.E. 85w/140 Multi- purpose gear oil) in Gearbox. • For all Grease Fittings use TYPE/grade II tube grease. STEP 1 Place rotary mower so that the deck is secure and level. STEP 2 Remove 1/2” Pipe Plug (Located at top of gearbox) and 1/8” Pip
Inhaltszusammenfassung zur Seite Nr. 12
SAFETY TRAINING Safety is a primary concern in the design and manufacture of our product. Un- fortunately, our efforts to provide safe equipment can be wiped out by a single careless act of an operator or bystander. In addition to the design and configuration of equipment, hazard control and ac- cident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of this equipment.
Inhaltszusammenfassung zur Seite Nr. 13
PREPARTION Never operate the tractor and mower until you have read and completely under- stand this manual, the Tractor Operator’s Manual, and each of the safety mes- sages found on the safety signs on the tractor and mower. Personal protection equipment including hardhat, safety glasses, safety shoes, and gloves are recommended during assembly, installation, operation, adjustment, maintenance, re- pairing, removal, or moving the implement. Do not allow long hair, loose fitting clothi
Inhaltszusammenfassung zur Seite Nr. 14
OPERATIONAL SAFETY The use of this equipment is subject to certain hazards that cannot be protected against by the mechanical means or product design. All operators of this equip- ment must read and understand this entire manual, paying particular attention to safety and operating instructions, prior to using. If there is something in this manual you do not understand, ask your supervisor, or your dealer, to explain it to you. Most accidents occur because of neglect or carelessn
Inhaltszusammenfassung zur Seite Nr. 15
OPERATIONAL SAFETY continued... Never allow the cutting blade to contact such items. Cut material higher at first, allowing rotary mower to clear hidden objects. Never assume an area is clear. Always Check! Always stop the tractor, disengage PTO, set brake, shut off the tractor engine, remove the ignition key, lower implement to the ground and allow mower blades to come to a complete stop before dismounting tractor. Never leave equipment unattended with the tractor running.
Inhaltszusammenfassung zur Seite Nr. 16
OPERATIONAL SAFETY continued... Pass rotary mower diagonally through sharp dips and avoid sharp drops to pre- vent “hanging up” tractor and rotary mower. Practice will improve your skills in maneuvering on rough terrain. Always cut down slopes, never across the face. Always check tractor manual for proper use on slopes. When using a unit, a minimum 20% of tractor and equipment weight must be on tractor front wheels. Without this weight, tractor could tip over, causing personal i
Inhaltszusammenfassung zur Seite Nr. 17
ATTACHING TO TRACTOR WARNING Never stand between tractor and rotary mower while backing up tractor to the hitch. STEP 1 Attach to tractor's category 1 three point hitch as described in the Tractor's Operator’s Manual. WARNING Failure to install retaining clip on gearbox input shaft would allow driveline to swing freely if bolt is sheared causing possible injury or death. STEP 2 Det
Inhaltszusammenfassung zur Seite Nr. 18
ATTACHING TO TRACTOR continued.... STEP 5 Place and hold inner PTO shaft section next to outer section and check if PTO shaft is too long. Each section should end approximately 3 inches short of reaching u-joint shield on the opposite section. If the shaft is too long measure 3 inches back from each u-joint shield and mark the other shaft section. Be sure to do this for both PTO shaft halves. NOTE: Do not cut PTO shaft sections at this time. STEP 6 Raise rotary mower and re
Inhaltszusammenfassung zur Seite Nr. 19
SIZING PTO SHAFT STEP 1 Cutting the PTO shaft to length. NOTE: Be sure to cut equal lengths of each PTO shaft section. Clamp end of PTO shaft in a vice and cut off shield where marked. (Figure 1-A & 1-B) Figure 1-A STEP 2 Using cut section of the shield as a guide cut shaft off the same amount. (Figure 2) STEP 3 Repeat steps 1 and 2 for other PTO shaft section. STEP 4 Figure 1-B Use a file to deburr PTO shafts. Clean up all chi
Inhaltszusammenfassung zur Seite Nr. 20
OPERATING INSTRUCTIONS This mower was designed to CUT PASTURE GRASS AND ROUGH AREAS UP TO 1" IN DIAMETER.. Use of your rotary mower to cut any material larger than 1" in diame- ter may damage the mower and void your warranty. PRE-OPERATIONAL ADJUSTMENTS Set tractor's lift control stop at a position that will prevent the PTO shaft from coming in contact with the front edge of the mower when it is at full lift. Consult your tractor manual for instructions. CUTTING HEIGHT ADJUS
