Inhaltszusammenfassung zur Seite Nr. 1
12’’ ELECTRIC LAWN MOWER
47336
Assembly, And OperA tiOn instructiOns
®
distributed exclusively by Harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sAVe tHis mAnuAl.
© ®
Copyright 2002 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained
herein may be reproduced in any shape or form
Inhaltszusammenfassung zur Seite Nr. 2
Specifications ITEM DESCRIPTION Power Requirement 110 VAC, 60 Hz, single phase, 13.8 startup amps Motor 2800 RPM, double insulated; centrifugal switch brake 30 inch, 16 AWG, UL approved; (requires connection to Line Cord an outdoor rated, 10 amp extension cord, not supplied) Power Switch Hand squeeze with lock-off safety button 12 inch hardened steel; Cutting Blade adjustment: 1 (min) - 3 (max) inches Height Adjustment Three position front and rear axles, spring loaded Wheel Size 4-3/4 inc
Inhaltszusammenfassung zur Seite Nr. 3
are recommended when working. Wear restrictive hair covering to contain long hair. When using the Electric Lawnmover always wear shoes with enclosed toes. Never use while barefoot or while wearing open toed shoes. 7. Use eye and ear protection. Always wear ANSI approved impact safety goggles and ear protection. 8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines. 9. Maintain tools with care. Keep tools sharp and clean for bet
Inhaltszusammenfassung zur Seite Nr. 4
19. Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician. 20. Pacemaker safety warning. People with pacemakers should consult with their physician(s) before using this product; operation of equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. Note: Performance of this tool may vary depending on variations in local line voltage. Exten- sion cord usage may also affect tool performance. W
Inhaltszusammenfassung zur Seite Nr. 5
Cable Clamps (39) and Cord Clamp (9) Screws (35) not shown Lower Handle (31B) Upper Handle (37) Knob (34) Screws (35) Lower Handle (31A) Cutter Housing (13) Grass Basket (19) and Screws (20) Screws (23) Assembly 1. Insert the Lower Handle (31B) into the hole on the right side of the Cutter Housing (13), and the Lower Handle (31A) into the hole on the left side. Tighten both Screws (23) that hold the Lower Handles in place. See photo above. 2. Attach the Upper Handle (37) to the Lower
Inhaltszusammenfassung zur Seite Nr. 6
1. Unplug the power cord. 2. Set the lawnmower on its side. 3. Using both hands, pull out the spring loaded front and rear axles to the desired height. The higher the wheel, the shorter the cut. Connecting the Power Cord 1. Attach an outdoor rated, 10 amp extension cord (not supplied) to the lawnmower Power Cord (40). 2. Secure the extension cord and Power Cord to the Cable Clamps (39) and Cord Clamp (9). This practice keeps both cords from lying around the Cutter Housing. 3. Connect the exte
Inhaltszusammenfassung zur Seite Nr. 7
2. Periodically check all nuts, bolts, and screws for tightness, especially the Blade bolt. 3. Store the Lawnmower in a clean, dry location. 4. Periodically lubricate the axles and wheels with a light oil. Cutting Blade Removal 1. To remove and refit the Blade (17), turn the Lawnmower over to reveal the Blade and Impeller (16). 2. Hold the Blade with a gloved hand. With the other hand, remove the Blade securing bolt and washer using a suitable spanner wrench. 3. Remove the Blade. If sharpening
Inhaltszusammenfassung zur Seite Nr. 8
PARTS LIST Part# Description Part# Description 1 Screw 29 Spring,Torsion 2 Upper Cover 30 Discharge Cover 3 Motor,Electric 31 Handle,Lower(A&B) 4 Washer 32 Connector 5 Washer,Spring 33 Nut 6 Screw 34 Knob 7 Sleeve 35 Screw 8* Screw 36* Switch 9* Cord Clamp 37 Handle,Upper 10 Connector Socket 38* Cord Jacket 11 Capacitor 39 Cable Clamps 12 Nylon Belt 40* Power Cord 13 Cutter Housing 41* Switch Handle 14 Wheel Cover 42* Screw 15 Wheel 43* Spring,Pushbutton 16 Impeller 44* Pushbutton 17 Blade 45* S
Inhaltszusammenfassung zur Seite Nr. 9
ASSEMBLY DIAGRAM SKU 47336 Page 9
Inhaltszusammenfassung zur Seite Nr. 10
limited 90 dA y WArrAnty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installati
