Inhaltszusammenfassung zur Seite Nr. 1
VISIMO (VM032+)
ROLLERMO (RM032)
EASIMO (EM032)
ROLLERMO
VISIMO
EASIMO
For all customer enquiries or for replacement parts, contact:-
☎ ☎ 0870 609 1901
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
Inhaltszusammenfassung zur Seite Nr. 2
Carton Contents switchbox start/stop lever lock off cable clip x 2 button grassbox washer x 4 upper handle handle wingknob x 4 bolt x 2 grassbox upper grassbox lower Easimo only grassbox tongue electric cable with moulded safety flap on plug lower handle x 2 motor cover deck instruction manual IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. The Loose Parts Pack is packaged underneath the deck of the product. IF ANY PARTS ARE MISSING CON
Inhaltszusammenfassung zur Seite Nr. 3
Electrical 2. Avoid operating your lawnmower in wet grass, 1. The British Standards Institute recommend the use where feasible. 3. Take care in wet grass, you may lose your footing. of a Residual Current Circuit Device (R.C.D.) with a tripping current of not more than 30mA. Even with 4. On slopes, be extra careful of your footing and wear a R.C.D. installed 100% safety cannot be guaran- non-slip footwear. teed and safe working practice must be followed at 5. Mow across the face of slopes, nev
Inhaltszusammenfassung zur Seite Nr. 4
Assembly Instructions A • The Loose Parts Pack is packaged under- 2 3 neath the deck. 1 Assembly of Lower Handles to Deck 1. Place the bolt (A2) through the hole in the lower handle (A1) until the lower handle fits into the recess (A3) B 2. Place the washer (B1) and the wing knob (B2) 1 on to the bolt and tighten the wing knob. 3. Repeat on the other side. Assembly of Upper Handles to Lower Handles. 2 1. Ensure the upper handle is located correctly with the lock-off button on the switchbox upp
Inhaltszusammenfassung zur Seite Nr. 5
Grassbox G 1 Fitting Fully Assembled Grassbox to Lawnmower. 3 1. Lift safety flap (G1) 2. Make sure the discharge chute is clean and free from debris (G2) 3. Locate fully assembled grassbox onto 2 location 2 points (G3) at the rear of the deck as illustrated in pic. H H 4. Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. • IMPORTANT ! AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX. • Removal is the reverse procedure. • For
Inhaltszusammenfassung zur Seite Nr. 6
Starting and Stopping M N To Start your Lawnmower 1. Form loop in mains cable and push the loop through the slot. (M) 2. To secure, position loop over the hook and pull the cable back through the slot (N). 3. Connect plug to mains and switch on. 4. Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn damage whilst starting. P Q The switchbox is provided with a lock-off button (P1) to prevent accidental starting. 5. Press and hold the lock-off butt
Inhaltszusammenfassung zur Seite Nr. 7
Removing and Fitting the Blade T Switch off, wait until the blade has stopped rotating and disconnect from the mains electrici- blade bolt ty supply BEFORE attempting to remove or refit the blade. Always handle the blade with care - sharp edges could cause injury. USE GLOVES. washer Removing the Blade 1. To remove the blade bolt, hold the blade firmly with a gloved hand and with a spanner, loosen the blade bolt by turning it anti-clockwise (T). blade 2. Remove the blade bolt, washer and blade.(
Inhaltszusammenfassung zur Seite Nr. 8
Caring for your Lawnmower Cleaning W1 W2 • USE GLOVES • IMPORTANT:- It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a poten- tial fire hazard. 1. Remove grass from under the deck with brush. (W1) 2. Using a soft brush - remove grass clippings from all air intakes (W2), the discharge chute (W3) and the grass box (W4). 3. Visimo Only - Using a soft brush, remove grass clip- pings from the vision window (W5). W3
Inhaltszusammenfassung zur Seite Nr. 9
Service Recommendations 1. We strongly recommend that your product is serviced 6. Should it be necessary for work to be carried out by your at least every twelve months, more often in a profes- Service Centre, it is important to take your complete sional application. machine including cable and any extension cables used. 2. Always use genuine Spare Parts. A network of specialist dealers can be found in your local 3. Prepacked spares are available from most Husqvarna Yellow Pages. Outdoor Product
Inhaltszusammenfassung zur Seite Nr. 10
EC Declaration of Conformity I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 6UP. NEWTON AYCLIFFE, Co. Durham. DL5 6UP NEWTON AYCLIFFE, Co. Durham. DL5 Certify that the product:- Certify that a sample of the above product has 6UP Certify that a sample
