Inhaltszusammenfassung zur Seite Nr. 1
Pub. 988-0151-121
www.lowrance.com
X37TX and X47TX
Fish-finding & Depth Sounding Sonars
Installation and Operation
Instructions
Inhaltszusammenfassung zur Seite Nr. 2
Copyright © 2003 Lowrance Electronics, Inc. All rights reserved. ® Lowrance is a registered trademark of Lowrance Electronics, Inc. Marine-Tex is a trademark of Illinois Tool Works Inc. Lowrance Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We reserve the right to do so without notice. All features and specifications subject to change without notice. All screens in this manual are simulated. On the cover: X47TX shown. For free own
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents Introduction...................................................................... 1 Capabilities and Specifications: X37TX and X47TX ......... 1 Installation Instructions................................................ 2 Installation Preparations.................................................... 2 Transducer Installation ...................................................... 3 Recommended Tools and Supplies.................................. 3 Selecting a Transducer Location
Inhaltszusammenfassung zur Seite Nr. 4
Display Adjustments......................................................... 35 Backlights ...................................................................... 35 Display Contrast............................................................ 36 Battery Voltage.............................................................. 36 Depth Units of Measure.................................................... 36 Preset Unit (Reset All Options)........................................ 36 System Info..........
Inhaltszusammenfassung zur Seite Nr. 5
Introduction Thank you for buying a Lowrance sonar! Your unit is a high-quality sonar designed for both professional and novice fishermen. All Lowrance sonars have an automatic mode that finds and displays the bottom, fish, underwater structure and more – right out of the box. All you have to do is press the on (PWR) key. However, if you want to fine-tune your unit, press the MENU UP key. The sonar has several powerful features you can control by scrolling through easy-to-use menus with the ar
Inhaltszusammenfassung zur Seite Nr. 6
Sonar Frequency:...................... 200 kHz. Transducers: .................. A Skimmer transducer comes packed with your sonar unit. Its 20° cone angle offers a wide fish detection area of up to 60º with high sensitivity settings. Operates at boat speeds up to 70 mph (61 kts). Transmitter: ................... 800 watts peak-to-peak; 100 watts RMS. Sonar sounding depth capability: ........... 600 feet (180 meters). Actual capability depends on transducer configuration and installation, botto
Inhaltszusammenfassung zur Seite Nr. 7
1. Determine the approximate location for the sonar unit, so you can plan how and where to route the cables for the transducer and power. This will help you make sure you have enough cable length for the desired configuration. 2. Determine the approximate location for the transducer and its cable route. 3. Determine the location of your battery or other power connection, along with the power cable route. 4. Install the transducer and route the transducer cable to the sonar unit. 5. Install the p
Inhaltszusammenfassung zur Seite Nr. 8
Trolling motor installations Tools: two adjustable wrenches, flat-head screwdriver. Supplies: plastic cable ties. Shoot-through hull installations Tools: these will vary depending on your hull's composition. Consult your boat dealer or manufacturer. Other tools are a wooden craft stick or similar tool for stirring and applying epoxy, and a paper plate or piece of cardboard to mix the epoxy on. Supplies: rubbing alcohol, 100 grit sandpaper, specially formulated epoxy adhesive available from LEI (
Inhaltszusammenfassung zur Seite Nr. 9
5. If possible, route the transducer cable away from other wiring on the boat. Electrical noise from engine wiring, bilge pumps and aerators can be displayed on the sonar's screen. Use caution when routing the transducer cable around these wires. CAUTION: Clamp the transducer cable to transom near the transducer. This will help prevent the transducer from entering the boat if it is knocked off at high speed. Good location Poor location Good location Good location Poor angle Good and poor transdu
Inhaltszusammenfassung zur Seite Nr. 10
If you cruise or fish around lots of structure and cover, your transducer may be frequently kicking up from object strikes. If you wish, you may move the transducer a little higher for more protection. There are two extremes you should avoid. Never let the edge of the mounting bracket extend below the bottom of the hull. Never let the bottom – the face – of the transducer rise above the bottom of the hull. Shoot-thru-hull vs. Transom Mounting In a shoot-thru-hull installation, the transducer is
Inhaltszusammenfassung zur Seite Nr. 11
1. Assembling the bracket. Press the two small plastic ratchets into the sides of the metal bracket as shown in the following illustration. Notice there are letters molded into each ratchet. Place each ratchet into the bracket with the letter "A" aligned with the dot stamped into the metal bracket. This position sets the transducer's coarse angle adjustment for a 14° transom. Most outboard and stern-drive transoms have a 14° angle. Dot Align plastic ratchets in bracket. 2. Aligning the transduce
Inhaltszusammenfassung zur Seite Nr. 12
3. Assembling the transducer. Once you determine the correct position for the ratchets, assemble the transducer as shown in the following figure. Don't tighten the lock nut at this time. Metal washer Nut Rubber Metal washer washers Bolt Assemble transducer and bracket. 4. Drilling mounting holes. Hold the transducer and bracket assembly against the transom. The transducer should be roughly parallel to the ground. The transducer's centerline should be in line with the bottom of the hull. Don't
Inhaltszusammenfassung zur Seite Nr. 13
Route cable over bolt and through bracket. Side view shown at left and seen from above at right. Attach the transducer to the transom. Slide the transducer up or down until it's aligned properly with the bottom of the hull as shown in the preceding and following figures. Tighten the bracket's mounting screws, sealing them with the sealant/adhesive compound. Adjust the transducer so that it's parallel to the ground and tighten the nut until it touches the outer washer, then add 1/4 turn. Do
Inhaltszusammenfassung zur Seite Nr. 14
Caution: If you drill a hole in the transom for the cable, make sure it is located above the waterline. After installation, be sure to seal the hole with the same marine grade above- or below-waterline sealant/adhesive used for the mounting screws. 7. Make a test run to determine the results. If the bottom is lost at high speed, or if noise appears on the display, try sliding the transducer bracket down. This puts the transducer deeper into the water, hopefully below the turbulence causing the n
Inhaltszusammenfassung zur Seite Nr. 15
TRANSDUCER ORIENTATION AND FISH ARCHES If you do not get good fish arches on your display, it could be because the transducer is not parallel with the ground when the boat is at rest in the water or at slow trolling speeds. Partial fish arches Transducer aimed Transducer aimed too far back too far forward Full fish arch Proper transducer angle Transducer angles and their effects on fish arches. If the arch slopes up – but not back down – then the front of the transducer is too
Inhaltszusammenfassung zur Seite Nr. 16
WARNING: Do not remove any material from your inner hull unless you know the hull's composition. Careless grinding or cutting on your hull can result in damage that could sink your boat. Contact your boat dealer or manufacturer to confirm your hull specifications. Fill with resin Fill with resin Inner hull Flotation material Epoxy to hull first Outer hull Epoxy the transducer to a solid portion of the hull. For example, some (but not all) manufacturers use a layer of fiberglass, then a core of b
Inhaltszusammenfassung zur Seite Nr. 17
To choose the proper location for shoot-thru-hull mounting, follow these testing procedures: (You may need a helper to complete these steps.) 1. Anchor the boat in about 30 feet of water. Add a little water to the sump of the boat. Plug the transducer into the sonar unit, turn it on, then hold the transducer over the side of the boat in the water. Adjust the sensitivity and range controls until a second bottom echo is seen on the display. (You'll need to turn off Auto Sensitivity, Auto Depth Ran
Inhaltszusammenfassung zur Seite Nr. 18
4. Most people can get good results by following steps 1 through 3, so this step is optional. If you want to make an extra effort to be absolutely sure that your selected location will work under all conditions, make a test run with the boat on plane and observe the bottom signal. You'll need to figure some way to prop the transducer into position while you make your test run. (A brick or two might be sufficient to hold it in place.) 5. When you're satisfied with a location, mark it and proceed
Inhaltszusammenfassung zur Seite Nr. 19
2. The epoxy consists of the epoxy itself and a hardener. Remove the two compounds from the package and place them on the paper plate. Thoroughly stir the two compounds together until the mixture has a uniform color and consistency. Do not mix too fast or bubbles will form in the epoxy. After mixing, you have 20 minutes to complete the installation before the epoxy becomes unworkable. Spread a thin layer of epoxy (about 1/16" or 1.5 mm thick) on the face of the transducer as shown in the previou
Inhaltszusammenfassung zur Seite Nr. 20
power cable when the unit is not in use. When you are not using the unit, you should always shut off power to the power cable, especially when the power cable is disconnected from the unit. Optional power off switch To unit for saltwater installations Black wire Red wire with 12 volt 3 amp fuse battery Power and transducer connections for the X37TX and X47TX sonar units (direct battery connection shown). If possible, keep the power cable away from other boat wiring, especially the engine's wir
