Inhaltszusammenfassung zur Seite Nr. 1
ORDER NO. CPD0811212CE
Notebook Computer
Model No. CF-30KTPAXxM
This is the Service Manual for
the following areas.
M …for U.S.A. and Canada
© Panasonic Corporation 2008.
Unauthorized copying and distribution is a violation of law.
Inhaltszusammenfassung zur Seite Nr. 2
WARNING For U.K. This apparatus must be earthed for your safety. To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connec- tion to earth. Wrongly wired extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power poi
Inhaltszusammenfassung zur Seite Nr. 3
LASER SAFETY INFORMATION . For U.S.A Class 1 LASER-Product This product is certified to comply with DHHS Rules 21 CFR Subchapter J. This product complies with European Standard EN60825 (or IEC Publication 825) For all areas This equipment is classified as a class 1 level LASER product and there is no hazardous LASER radiation. Caution: (1) Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. (2) The drive is de
Inhaltszusammenfassung zur Seite Nr. 4
SAFETY PRECAUTIONS 1. Before servicing, unplug the power cord to prevent an electric shock. 2. When replacing parts, use only manufacture's recommended components for safety. 3. Check the condition of the power cord. Replace if wear or damage is evident. 4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc. Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to
Inhaltszusammenfassung zur Seite Nr. 5
Precautions (Battery Pack) When the Battery Pack Has Become Degraded, Do Not Use with Any Other Product Replace It with a New One The battery pack is rechargeable and was intended for Continued use of a degraded b ttery pack may generate the specified product. If it is used with a product other a high levels of heat, cause a fire to start and cause the than the one for which it was designed, electrolyte leak- pack to burst or explode. age, generation of heat, ignition or rupture may result. Do
Inhaltszusammenfassung zur Seite Nr. 6
CONTENTS 1. Specifications 1-1 2. Names and Functions of Parts 2-1 3. Block Diagram 3-1 4. Diagnosis Procedure 4-1 5. Power-On Self Test (Boot Check) 5-1 6. List of Error Codes 6-1 7. Self Diagnosis Test 7-1 8. Wiring Connection Diagram 8-1 9. Disassembly/Reassembly 9-1 10. Exploded View 10-1 11. Replacement Parts List 11-1
Inhaltszusammenfassung zur Seite Nr. 7
1. Specifications This page provides the specifications for the basic model. The model number is different according to the unit configuration. To check the model number: Check the bottom of the computer or the box the computer came in at the time of purchase. To check CPU speed, memory size and the hard disk drive (HDD) size: Run the Setup Utility ( Reference Manual “Setup Utility”) and select [Information] menu. [CPU Speed]: CPU speed, [System Memory]: Memory size, [Hard Disk]: Hard disk d
Inhaltszusammenfassung zur Seite Nr. 8
Main Specifications Weight Approx. 3.8 kg {Approx. 8.4 lb.}, excluding the dummy pack and dummy cards (Approx. 50g {Approx. 1.8 oz.}) Operation Environment Temperature: 5 °C to 35 °C {41 °F to 95 °F} Humidity: 30% to 80% RH (No condensation) Storage Environment Temperature: -20 °C to 60 °C {-4 °F to 140 °F} Humidity: 30% to 90% RH (No condensation) Operating System ® Windows Vista Business Service Pack 1 ® ® Microsoft Windows XP Professional Service Pack 2 with Advanced Security Technologies
Inhaltszusammenfassung zur Seite Nr. 9
*13 V V The AC adaptor is compatible with power sources up to 240 AC adaptor. The computer is supplied with a 125 AC compat- ible AC cord. 20-M-2-1 *14 Varies depending on the usage conditions. *15 2 Measured at LCD brightness: 60 cd/m Varies depending on the usage conditions, or when an external device is attached. *16 Approx. 0.9 W when the battery pack is fully charged (or not being charged) and the computer is OFF. *17 Rated power consumption 23-E
Inhaltszusammenfassung zur Seite Nr. 10
2. Names and Functions of Parts F G H I J K K A L EX K PC M D N E O A: Bluetooth Antenna : Hard disk drive status : Power status of the multimedia pocket Reference Manual “Bluetooth” : Battery status Reference Manual “Battery Power” B: ExpressCard Slot : Power status Reference Manual “PC Card / ExpressCard” (Off: Power off/Hibernation, Green: Power C: PC Card Slot on, Blinking green: Sleep/ Reference Manual “PC Card / ExpressCard” Standby, Blinking green
Inhaltszusammenfassung zur Seite Nr. 11
Right side AB C D E F G H I 1394 Rear side Bottom Q J H K L M N O P R A: Hard Disk Drive N: Headphone Jack You can connect headphones or amplified speakers. Reference Manual “Hard Disk Drive” When they are connected, audio from the internal B: SD Memory Card Slot speakers is not heard. Reference Manual “SD Memory Card” O: Microphone Jack C: SD Memory Card Indicator A condenser microphone can be used. other types of microphones are used, audio input may not be pos- (Blinking: During access) s
Inhaltszusammenfassung zur Seite Nr. 12
3 Block Diagram 3-1 Penryn DC T TM M I Intel Co ntel Core re 2 6MB L2 Cache Duo pro Duo processor essor 1.6GHz, FSB 1066MHz (Penryn (Penryn) SL9300 SL9300 L LV V1.6G 1.05V 5.3Gbytes/sec AMP Speaker SO-DIMM Memory L LCD CD 64bit BUS 1.8V 667MHz Internal DRAM DDR2 SDRAM 1 13.3 3.3” XGA XGA RJ11 Graphics Interface 2GB 1 1000+ 000+ n ni it t Sound Headphone HDA Data Modem CRT SO-DIMM Memory DMI AD1883 Ext. MIC INTEL 64bit BUS
Inhaltszusammenfassung zur Seite Nr. 13
4 Diagnosis Procedure 4.1. Basic Procedures 4-1
Inhaltszusammenfassung zur Seite Nr. 14
4.2. Troubleshooting Please take note of the following two points with regard to troubleshooting: 1. Know-how of diagnosis upon occurrence of heavy troubles, e.g. Set cannot be turned ON, Set fails to start, No display on screen , etc. 2. Explanation of each trouble, mainly symptom of trouble in operation. Flow Chart Pay attention to the following points when in pursuit of the cause of a troubleshooting. 1. Peripheral apparatus connected with the set should all be removed before opera
Inhaltszusammenfassung zur Seite Nr. 15
5 Power-On Self Test (Boot Check) Outline of POST The set has a boot check function called POST (Power-On Self Test) in it. The condition of the main body is diagnosed by checking beep sound or error code. Start .............Test begins automatically when power switch is set to ON. Normal finish .....After memory checking, a beep sound is issued once and the set is placed into automatic stop. Note: If no error occurs, nothing is displayed. (No display of OK, etc.) Error Diagnosis by Checkin
Inhaltszusammenfassung zur Seite Nr. 16
6 List of Error Codes The following is a list of the messages that BIOS can display. Most of them occur during POST. Some of them display information about a hardware device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it has been configured. Following the list are explanations of the messages and remedies for reported problems. If your system displays one of except the messages marked below wi
Inhaltszusammenfassung zur Seite Nr. 17
02D0 System cache error - Cache disabled Contact Panasonic Technical Support. 02F0: CPU ID: CPU socket number for Multi-Processor error. 02F4: EISA CMOS not writable ServerBIOS2 test error: Cannot write to EISA CMOS. 02F5: DMA Test Failed ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers. 02F6: Software NMI Failed ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt). 02F7: Fail - Safe Timer NMI Failed ServerBIOS2 test error: Fail
Inhaltszusammenfassung zur Seite Nr. 18
7 Self Diagnosis Test As for the self-diagnosis test(PC-Diagnostic utility) to use this model, a standard test and the enhancing test by the module of the main body building in are possible. NotesTo skip BIOS password Use + key to skip BIOS password or authentication of fingerprint. This key is only for entering DIAG mode. Not available to boot the computer. If customer set "HDD Lock", the DIAG program cannot perform HDD test. *This key is for serv
Inhaltszusammenfassung zur Seite Nr. 19
2. Operation of PC-Diagnostic Utility -Only the device which can be inspected on the entire screen is displayed. -The item does not appear when the device of wireless LAN etc. is not physically connected. -The movement of the item must use an arrow key or a flat pad. -As for the device under the diagnosis, blue and yellow are alternately displayed at the left of the icon. - The diagnosis result of the device greens at the left of the icon when it is normal, and becomes red when abnormal. -When t
Inhaltszusammenfassung zur Seite Nr. 20
2-1. Selection of tested device -To test only a specific device, "Test" and "Do not test" of each device can be selected. -The device which can select the enhancing test changes in order of "The standard is tested" and "Do not test" whenever the device icon is clicked. Start the standard test Do not test Please begin testing clicking if the selection of the tested device ends.
