Inhaltszusammenfassung zur Seite Nr. 1
Crestron TPS-6X-BTP
Battery Pack for TPS-6X
Installation Guide
Inhaltszusammenfassung zur Seite Nr. 2
This document was prepared and written by the Technical Documentation department at: Crestron Electronics, Inc. 15 Volvo Drive Rockleigh, NJ 07647 1-888-CRESTRON All brand names, product names and trademarks are the property of their respective owners. ©2008 Crestron Electronics, Inc.
Inhaltszusammenfassung zur Seite Nr. 3
Crestron TPS-6X-BTP Battery Pack for TPS-6X Contents Battery Pack for TPS-6X: TPS-6X-BTP 1 Introduction ...............................................................................................................................1 Features and Functions................................................................................................1 Specifications ..............................................................................................................2 Physical Desc
Inhaltszusammenfassung zur Seite Nr. 4
Inhaltszusammenfassung zur Seite Nr. 5
Crestron TPS-6X-BTP Battery Pack for TPS-6X Battery Pack for TPS-6X: TPS-6X-BTP Introduction ® The Crestron TPS-6X-BTP is a replacement NiMH rechargeable battery pack for the TPS-6X Wireless Touchpanel. One TPS-6X-BTP is included with each TPS-6X. Installation of the TPS-6X-BTP battery pack requires tools and should be performed by a qualified technician. Features and Functions • Replacement NiMH rechargeable battery pack for the TPS-6X Wireless Touchpanel • Fast charging Nickel Me
Inhaltszusammenfassung zur Seite Nr. 6
Battery Pack for TPS-6X Crestron TPS-6X-BTP Specifications Specifications for the TPS-6X-BTP are listed in the following table. TPS-6X-BTP Specifications SPECIFICATION DETAILS Output Voltage 4.8 Volts DC Capacity 2000 mAh Composition Nickel Metal Hydride (NiMH) Usage Per Charge ~2 hours continuous, ~24 hours under normal use (10% active duty cycle with standby/powerdown activated Charging Time ~2.5 hours (~2.5 to 3 hours when in use) Optimal Operating 32º to 112º F (0º to 45º C)
Inhaltszusammenfassung zur Seite Nr. 7
Crestron TPS-6X-BTP Battery Pack for TPS-6X Physical Description The TPS-6X-BTP consists of two battery cells, along with the integrated wiring. It has a multi-pin connector for attachment inside the TPS-6X. TPS-6X-BTP Physical View Installation Guide – DOC. 6740A Battery Pack for TPS-6X: TPS-6X-BTP • 3
Inhaltszusammenfassung zur Seite Nr. 8
Battery Pack for TPS-6X Crestron TPS-6X-BTP Setup Removal NOTE: The TPS-6X Wireless Touchpanel contains ESD (electrostatic discharge) sensitive devices. To avoid damaging the unit, perform the following procedure while wearing a grounding strap that is properly grounded or on a grounded workstation. NOTE: To prevent damage to the multi-pin connector and wiring, use care when handling the TPS-6X-BTP. Perform the following procedure to remove the existing TPS-6X-BTP from a TPS-6X touc
Inhaltszusammenfassung zur Seite Nr. 9
Crestron TPS-6X-BTP Battery Pack for TPS-6X 2. Remove the four screws that secure the front bezel to the touchpanel and return the unit to its normal, face-up position. (Use care and hold the bezel to the rest of the touchpanel. If the bezel separates from the rest of the touchpanel while rotating the unit to its normal position, the internal parts of the panel may spill out.) 3. Lift the front bezel from the touchpanel, then place the touchpanel assembly face down on the work surface. 4
Inhaltszusammenfassung zur Seite Nr. 10
Battery Pack for TPS-6X Crestron TPS-6X-BTP 5. Remove the orange tape securing the battery pack wires to the circuit board and the two pieces of clear tape on each battery cell. (Refer to illustration below.) TPS-6X Assembly (Removed from Enclosure) 6 • Battery Pack for TPS-6X: TPS-6X-BTP Installation Guide – DOC. 6740A
Inhaltszusammenfassung zur Seite Nr. 11
Crestron TPS-6X-BTP Battery Pack for TPS-6X 6. Using the flat end of a small slot head screwdriver, gently separate the multi-pin connector from the corresponding connector on the circuit board of the TPS-6X. (Refer to illustration below.) TPS-6X-BTP Connector on TPS-6X 7. Remove battery cells with the connecting wires attached, from either side of the assembly. Installation Guide – DOC. 6740A Battery Pack for TPS-6X: TPS-6X-BTP • 7
Inhaltszusammenfassung zur Seite Nr. 12
Battery Pack for TPS-6X Crestron TPS-6X-BTP Installation NOTE: The TPS-6X Wireless Touchpanel contains ESD (electrostatic discharge) sensitive devices. To avoid damaging the unit, perform the following procedure while wearing a grounding strap that is properly grounded or on a grounded workstation. After completing removal of the old TPS-6X-BTP from the TPS-6X touchpanel (refer to “Removal” on page 4), perform the following procedure to install the new TPS-6X-BTP. A #1 Phillips screwdr
Inhaltszusammenfassung zur Seite Nr. 13
Crestron TPS-6X-BTP Battery Pack for TPS-6X 3. Carefully connect the multi-pin connector of the TPS-6X-BTP with the corresponding connector on the circuit board of the TPS-6X. 4. Dress the cables of the TPS-6X-BTP as shown in the illustration below and apply the 2-inch (50 mm) piece of orange tape that came with the TPS-6X-BTP to hold the wires in place. 5. Apply the two 1 inch (25 mm) pieces of orange tape that came with the TPS-6X-BTP to each battery cell, extending the tape to the b
Inhaltszusammenfassung zur Seite Nr. 14
Battery Pack for TPS-6X Crestron TPS-6X-BTP 6. Carefully turn the assembly over, returning it to its normal, face-up position. Then place the assembly into the rear half of the TPS-6X enclosure, hinging it so the top of the assembly is in place first (as shown in the illustration below). Then settle the bottom of the assembly into place and with your thumbs on the black plastic at the left and right edges, press and snap the assembly into place. Installation (Showing Top of Assembly in P
Inhaltszusammenfassung zur Seite Nr. 15
Crestron TPS-6X-BTP Battery Pack for TPS-6X Charging NOTE: A Nickel Metal Hydride (NiMH) battery typically provides 500 charge/discharge cycles. To charge the TPS-6X-BTP, install the TPS-6X-BTP in a TPS-6X touchpanel and mount the touchpanel on a powered TPS-6X-DS or TPS-6X-DS-C Docking Station/Charger (TPS-6X-DS-C sold separately). NOTE: The battery pack may take up to three hours to charge in a powered touchpanel if the panel is in use during charging. Storage Over time, the capac
Inhaltszusammenfassung zur Seite Nr. 16
Battery Pack for TPS-6X Crestron TPS-6X-BTP To prolong the life and maintain the performance of your NiMH batteries, Crestron recommends you follow these steps: • Practice FIFO (First In and First Out) inventory rotation. • Never store batteries under load. • Store batteries in a temperature controlled environment (refer to table below). • Store batteries at 65% (± 20%) relative humidity and keep out of direct sunlight. • Cycle batteries at least one charge/discharge cycle according to
Inhaltszusammenfassung zur Seite Nr. 17
Crestron TPS-6X-BTP Battery Pack for TPS-6X Resources Industry Compliance As of the date of manufacture, the TPS-6X-BTP has been tested and found to comply with specifications for CE marking and standards per EMC and Radiocommunications Compliance Labelling. Reference Documents The latest version of all documents mentioned within the guide can be obtained from the Crestron website (www.crestron.com/manuals). This link will provide a list of product manuals arranged in alphabetic
Inhaltszusammenfassung zur Seite Nr. 18
Battery Pack for TPS-6X Crestron TPS-6X-BTP Future Updates As Crestron improves functions, adds new features and extends the capabilities of the TPS-6X-BTP, additional information may be made available as manual updates. These updates are solely electronic and serve as intermediary supplements prior to the release of a complete technical documentation revision. Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as an “Addendu
Inhaltszusammenfassung zur Seite Nr. 19
Crestron TPS-6X-BTP Battery Pack for TPS-6X Return and Warranty Policies Merchandise Returns / Repair Service 1. No merchandise may be returned for credit, exchange or service without prior authorization from CRESTRON. To obtain warranty service for CRESTRON products, contact an authorized CRESTRON dealer. Only authorized CRESTRON dealers may contact the factory and request an RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of the problem, name and phon
Inhaltszusammenfassung zur Seite Nr. 20
Crestron Electronics, Inc. Installation Guide – DOC. 6740A 15 Volvo Drive Rockleigh, NJ 07647 (2022218) Tel: 888.CRESTRON 10.08 Fax: 201.767.7576 Specifications subject to www.crestron.com change without notice.
