Bedienungsanleitung American Standard Dazzle 6028.240

Inhaltszusammenfassung zur Seite Nr. 1

Installation
Instructions
DAZZLE
6028.240
Mini Spread Lavatory Faucet with
Speed Connect Drain*
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Speed Connect Drain*
• 1/3 of the parts, installs in 1/3 of the time
Certified to comply with ANSI A112.18.1
• No tools needed
M968491 Rev. 1.2
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is

Inhaltszusammenfassung zur Seite Nr. 2

POP-UP DRAIN 2 Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 DRAIN Remove CARDBOARD SPACER (2) from under BODY DRAIN POP-UP (3). 3 Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 4 2 REMOVE FLANGE 3 Fig. A. Fig. B. 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. 4 2 3 INSTALL DRAIN FROM TIGHTEN LOCKNUT 4 BE

Inhaltszusammenfassung zur Seite Nr. 3

FRONT ATTACH CABLE CONNECTOR 7 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. CHECK OPERATION OF POP-UP 8 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 2 MAKE WAT

Inhaltszusammenfassung zur Seite Nr. 4

INSTALL HANDLES 10 5 Turn VALVE into OFF position. 8 4 Push ADAPTER (1) into VALVE STEM (2). Align HANDLE (3) and install onto ADAPTER (1). 3 Install HANDLE SCREW (4) and tighten to secure HANDLE (3). Insert INDEX BUTTON (5). 1 2 TEST INSTALLED FITTING 10a 7 With HANDLES (3) in OFF position, turn on WATER SUPPLIES (6) and check all connections for leaks. Remove AERATOR (7). Operate both HANDLES (3) to flush water lines thoroughly. 9 Replace AERATOR (7). CHECK DRAIN CONNECTIONS Operate POP-UP KNOB

Inhaltszusammenfassung zur Seite Nr. 5

Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. C

Inhaltszusammenfassung zur Seite Nr. 6

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice Fig. G. that the Loop is on one side of the Stopper. Fig. G. LOGO To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front. Rotate Stopper s