Inhaltszusammenfassung zur Seite Nr. 1
VF02
Inhaltszusammenfassung zur Seite Nr. 2
Dear Customer, ® Thank you for purchasing the Verilux EasyFlex Deluxe ® Natural Spectrum Floor Lamp. You have received a quality product, backed by a one-year limited warranty. Many other healthy lighting products are available through our catalog and online. Visit us on the web at www.verilux.com to request a free catalog and learn more about all our quality Verilux products, or call our toll-free number 1-800-454-4408. As a Verilux customer, your satisfaction means everything to us. We
Inhaltszusammenfassung zur Seite Nr. 3
Important Safety Instructions SAVE THESE INSTRUCTIONS ® ® Thank you for purchasing the EasyFlex Deluxe Natural Spectrum Floor Lamp. Please read the following safety information before using. To reduce the risk of fi re, electrical shock, or injury to persons: • Do not dismantle. • Do not alter power cord. • Turn off/unplug and allow to cool before replacing bulb or cleaning. • For indoor use only. General Precautions • The lamp is an electrical device. Do not use near water. • Before plugging
Inhaltszusammenfassung zur Seite Nr. 4
Getting Started Main Parts & Controls B C A. Ergonomic Handle B. Lamp Head C. High/Off/Low Switch D. Gooseneck E. Shaft F. Ergonomic Height Adjustment Lever G. Lamp Base H. Power Cord A I. Ballast D J. LED Indicator K. Bulb L. Parabolic Light Diffuser Close-up of Lamp Head E L F K H Close-up of Ballast J I G 4
Inhaltszusammenfassung zur Seite Nr. 5
Getting Started — continued ® Please Read Instructions Carefully Before Using the EasyFlex . 1. Unpack lamp carefully, removing all packaging material, and confi rm you have all parts shown in the diagram. For your convenience, the bulb has been inserted into the socket. 2. Remove all pieces from box. Locate the 2 screws and tightening tool in the plastic bag and set aside. 3. Detach the red plastic pieces and store them in the event you need to return the lamp. 4. The clear plastic sleeve o
Inhaltszusammenfassung zur Seite Nr. 6
Assembly Instructions 1. Set the lamp base on the fl oor and insert the lamp shaft over the base support unit until the screw holes line up as shown in Fig. 1. Insert the screw using the tightening tool and turn clockwise to tighten. Close-up of screw hole in the lamp base Fig. 1 2. Hold the upper shaft with one hand and release the ergonomic height adjustment lever by gently pulling it upward as shown in Fig. 2. Extend the upper shaft approximately 12". Lock the adjustment lever by g
Inhaltszusammenfassung zur Seite Nr. 7
Assembly Instructions — continued 3. Attach the lamp head gooseneck to the shaft until the screw holes line up as shown in Fig. 3. Use care when tucking the wire into the shaft. Form a loop with any excess wire prior to tucking it. Insert the screw using the tightening tool and turn clockwise to tighten. Close-up of screw hole in the lamp head Fig. 3 4. Remove the light diffuser from the protective plastic bag. Insert the plastic pegs at the bottom of the light diffuser into the open
Inhaltszusammenfassung zur Seite Nr. 8
Assembly Instructions — continued 5. Attach the ballast to the power cord. Use care to align the 4-pin plug properly. DO NOT FORCE. The power cord is designed to connect only one way (Fig. 5). Fig. 5 6. Plug the ballast into a standard 120V 50/60Hz outlet and turn the lamp on. The J green LED indicator (J) on center of the ballast will illuminate (Fig. 6). If not, please refer to the troubleshooting section of this manual (see page 11). Note: Green LED indicator will not illuminate if
Inhaltszusammenfassung zur Seite Nr. 9
Bulb Replacement Removal 1. Unplug the lamp from the power source. 2. To access the bulb, remove light diffuser by depressing the tab and lifting it out (Fig. 7). 3. Firmly hold the bulb base (B) and pull bulb (C) from the socket (A) in an outward motion (Fig. 8). Fig. 7 Installation 1. Unplug the lamp from the power source. B 2. Firmly hold the base (B) and push bulb (C) into the socket (A). D 3. Be sure the bulb is fi rmly seated in the socket (Fig. 9) and snapped into the metal bulb cli
Inhaltszusammenfassung zur Seite Nr. 10
Care and Cleaning Your lamp is made from high quality materials that will last for many years with minimum care. You may want to periodically clean the lamp using a mild, non-abrasive cleaner and soft cloth. When cleaning, make sure you have turned off and unplugged the unit and allowed suffi cient time for the unit to cool. All liquid should be properly wiped away and dried prior to restoring power. CAUTION: DO NOT USE SOLVENTS OR CLEANERS CONTAINING ABRASIVES, OR AMMONIA BASED CLEANERS. W
Inhaltszusammenfassung zur Seite Nr. 11
Troubleshooting ® Before Requesting Service on your Verilux Lamp, Please Read the Following: • Make sure all power connectors, cords and plugs are inserted fully and securely. • Be sure the bulb is securely seated into the socket (See page 9). • Make sure there is power to the wall outlet or try another outlet. PROBLEM CHECK SOLUTION Has the plug come Insert plug securely into wall outlet. loose? Light Won’t Is the bulb old? Check bulb for blackening/darkening at bottom of spiral where it join
Inhaltszusammenfassung zur Seite Nr. 12
One Year Limited Warranty ATTENTION! ONCE OPENED, PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED FOR REPAIR OR REPLACEMENT! Many questions may be answered by visiting www.verilux.com, or you may call our Customer Service Department at 800-786-6850 during normal business hours. This limited warranty is provided by: Verilux, Inc., 340 Mad River Park, Waitsfi eld, VT 05673 Verilux warrants this product to be free from defects in material and workmanship for a period of one
