Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION INSTRUCTIONS
Single and Dual Display Floor Stands
MF1, MF2, PF1, PF2 Series
Inhaltszusammenfassung zur Seite Nr. 2
MF1, MF2, PF1, PF2 Series Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and CSAV, Inc., and its affiliated corporations and subsidiaries follow all instructions can result in serious personal injury, (collectively, "CSAV"), intend to make this manual accurate and damage to equipment, or voiding of factory warranty! It is the complete. However, CSAV makes no claim that the information installer’s responsibility to make sure all components are contained her
Inhaltszusammenfassung zur Seite Nr. 3
Installation Instructions MF1, MF2, PF1, PF2 Series DIMENSIONS MF1, MF2 [1463] 57-5/8 [1316] 51-7/8 [889] 35 [661] 26 [431] 17 [2327] 91-5/8 [2180] 85-7/8 [1211] 47-5/8 [39] 1-1/2 [44] [65] 1-3/4 2-1/2 PF1, PF2 3
Inhaltszusammenfassung zur Seite Nr. 4
Installation Instructions MF1, MF2, PF1, PF2 Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Beve
Inhaltszusammenfassung zur Seite Nr. 5
Installation Instructions MF1, MF2, PF1, PF2 Series TOOLS REQUIRED FOR INSTALLATION 1/4" (To remove base 3/16" plates from packaging) (included) PARTS A (1) D (1) F (1) (D) (PF Only) [(2) for Dual OR Display Models] (E) B (1) (Single Display Models Only) C [(2) for Single Display Models] [(4) for Dual Display Models] E (1) (Front) (MF Only) [(2) for Dual Display Models] G (4) J (1) H (1) 3/16" 3/16" N (4) P (1) L (12) M (4) Q (4) K (1) 5/16-18 x 3/4" 5/16-18 x 1-1/2" 5/16" 1/
Inhaltszusammenfassung zur Seite Nr. 6
MF1, MF2, PF1, PF2 Series Installation Instructions 2. Gather stand base pieces B and C (2) as shown in Figure 3 ASSEMBLY and push them together until the edges meet. (B) CAUTION: Attachment holes may be damaged if a power drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the hex head drill bit and power drill to complete the attachment. Assembling Base for Single Display Stand 1. Attach
Inhaltszusammenfassung zur Seite Nr. 7
Installation Instructions MF1, MF2, PF1, PF2 Series (PF1 Shown) (Back view of stand) (M) x 4 (D) or (E) (C) x 4 (F) Figure 5 3. Place top base section and center post assembly on top of Figure 7 the four base pieces. (See Figure 6) 4. Fasten lower base pieces to top base section and center Attaching Dual Head Assembly post assembly using twelve 5/16-18 x 1/2" flat head cap 1. Place head assembly (D) or (E) on the front of the stand screws (L). (See Figure 6) assembly. (See Figure 8) (M) x 4 3 (L
Inhaltszusammenfassung zur Seite Nr. 8
MF1, MF2, PF1, PF2 Series Installation Instructions Attaching Display to Stand WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY 5 MAY LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to ensure the total amount of weight placed on the stand does not exceed 125 lbs (56.70 kg) for the MF1, 250 lbs (113.40 kg) for the MF2 [125 lbs (56.70 kg) per faceplate]; 200 lbs (90.72 kg) for the PF1, 400 lbs (181.44 kg) for the PF2 [200 lbs (90.72 kg) per faceplate]. CAUTIO
Inhaltszusammenfassung zur Seite Nr. 9
Installation Instructions MF1, MF2, PF1, PF2 Series Tilting Display o (Rear (Front view The display(s) can be tilted up to 15 either backward or 2 view of of center post) forward from a straight upright position. In a dual stand, the center post) tilting is only restricted by the size of the display. 1 3 1. Turn knob counterclockwise on back of head assembly to loosen the tilt. (See Figure 12) Exits for signal cables Exit for 3 1 power Snap-on cables covers 4 Place optional bolt (not provided) h
Inhaltszusammenfassung zur Seite Nr. 10
MF1, MF2, PF1, PF2 Series Installation Instructions Using the Stand Remove bolt 1 or padlock CAUTION: This stand is intended for use only with the 2 if used products and maximum weights indicated: 125 lbs (56.70 kg) for the MF1, 250 lbs (113.40 kg) for the MF2 [125 lbs (56.70 kg) per faceplate]; 200 lbs (90.72 kg) for the PF1, 400 lbs (181.44 kg) for the PF2 [200 lbs (90.72 kg) per faceplate]. Use with other products or products heavier than the maximum weights indicated may result in instabilit
Inhaltszusammenfassung zur Seite Nr. 11
Installation Instructions MF1, MF2, PF1, PF2 Series 11
Inhaltszusammenfassung zur Seite Nr. 12
MF1, MF2, PF1, PF2 Series Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. 8809-000039 Rev. C 2007 Chief Manufacturing www.chiefmfg.com P +86-755-8996 9226 11/07 F +86-755-8996 9217
