Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are hereby gra
Inhaltszusammenfassung zur Seite Nr. 3
CONTENTS 1 INTRODUCTION .......................................................................................... 1 2 INSTALLATION............................................................................................ 2 ® 2.1 PowerScan D8330 Interface Cable Connections ........................................2 2.2 BC-80X0 Interface Cable Connections .........................................................4 2.3 RS-232 Connection.......................................................
Inhaltszusammenfassung zur Seite Nr. 4
® 4.6 PowerScan M8300/STAR-System™ Setup ..............................................31 4.7 BC-8000 STAR-System™ Network Setup ..................................................33 4.8 Interface Selection ......................................................................................35 4.9 USB Reader Configuration..........................................................................38 4.10 Changing Default Settings ...............................................................
Inhaltszusammenfassung zur Seite Nr. 5
5.9.1 Radio Protocol Timeout ............................................................................ 158 5.9.2 Radio RX Timeout..................................................................................... 159 5.9.3 Power-Off Timeout.................................................................................... 159 5.9.4 Transmission Mode................................................................................... 160 5.9.5 Beeper Control for Radio Response .........
Inhaltszusammenfassung zur Seite Nr. 6
GENERAL VIEW ® POWERSCAN D8330/M8300 READERS LEDs ® POWERSCAN D8330 Cable Connector ® POWERSCAN M8300 Battery Cover Laser Output Window Trigger ® Figure A – PowerScan D8330/M8300 Series Readers LEDs Keypad Display Laser Output Window ® Figure B – PowerScan M8300 Series Readers with Display vi
Inhaltszusammenfassung zur Seite Nr. 7
BC-80X0 / C-8000 CRADLES Scan Finder Button LEDs Figure C – BC-8000 The label on the cradle contains LED indicators and a scan finder button. When the button is pressed, the cradle transmits a “broadcast” message. All properly configured scanners (Radio RX Timeout set to keep the radio “awake”) linked to that base (through a bind or a join sequence) and within radio range coverage will emit a beep sequence once every 2 seconds for 30 seconds. A scanner is considered to be linked w
Inhaltszusammenfassung zur Seite Nr. 8
Inhaltszusammenfassung zur Seite Nr. 9
INTRODUCTION 1 INTRODUCTION ® Datalogic renews its range of industrial laser scanners introducing the PowerScan ® ® family: PowerScan D8330 and PowerScan M8300. Robustness and ergonomics remain unsurpassed: clearly audible beeper and bright "good read" LEDs for areas where noise levels are normally high; the aim mode, which helps point to the right ® code, has now been extended to the whole PowerScan family. Optical parts are completely suspended on shock absorbers and a careful cho
Inhaltszusammenfassung zur Seite Nr. 10
® POWERSCAN D8330/M8300 2 INSTALLATION Connections should always be made with power OFF! CAUTION ® 2.1 POWERSCAN D8330 INTERFACE CABLE CONNECTIONS ® The PowerScan D8330 reader incorporates a multi-standard interface, which can be connected to a Host by plugging the correct interface cable into the connector and closing the cable cover. A. Rubber gasket B. Plastic boot C. Cable spacer D. Cover E. Strain relief 2
Inhaltszusammenfassung zur Seite Nr. 11
INSTALLATION Follow the given procedure for correct cable insertion: 3 Align 2 5 1 6 Notch 4 7 Arrow Tab Slip the cover over the cable. Push the plastic boot into the rubber gasket. Take care that the tab on the plastic boot is aligned with the notch in the rubber gasket. Push the plastic boot and gasket into the handle. Ensure that the “Front” marking on the plastic boot is facing out, with the arrow pointing towards the front of the scanner. Insert the cable into t
Inhaltszusammenfassung zur Seite Nr. 12
® POWERSCAN D8330/M8300 2.2 BC-80X0 INTERFACE CABLE CONNECTIONS Power Interface Cable BC-80X0 Connectors The BC-80X0 incorporates a multi-standard interface, which can be connected to a Host by simply plugging the correct interface cable into the Host connector, placed on the base of the cradle. In addition the cradle must be connected to an external power supply. Disconnecting the BC-80X0 Cable To disconnect the cable, insert a paper clip or other similar object into
Inhaltszusammenfassung zur Seite Nr. 13
INSTALLATION 2.3 RS-232 CONNECTION 2.4 USB (if required) 5
Inhaltszusammenfassung zur Seite Nr. 14
® POWERSCAN D8330/M8300 2.5 IBM USB POS (if required) 6
Inhaltszusammenfassung zur Seite Nr. 15
INSTALLATION 2.6 WEDGE CONNECTION 2.7 PEN EMULATION CONNECTION 7
Inhaltszusammenfassung zur Seite Nr. 16
® POWERSCAN D8330/M8300 2.8 NETWORK CONNECTIONS 2.8.1 BC-8060 Network Connectors The multidrop network is a bus system which is propagated from one BC-8060 cradle to another using individual cables. This is possible thanks to the RS-485 connector on the front panel of the cradle. Power Supply MULTI-INTERFACE RS-485 RS-232, USB, Wedge, (BC-8060only) PEN Emulation All cradles are connected together within the bus system through the Datalogic RS-485 splitter
Inhaltszusammenfassung zur Seite Nr. 17
INSTALLATION 2.8.2 Network Cabling The Multidrop line is made using RJ45 connectors and a cable having the following specifications: • twisted pair AWG 24 wires • 120 Ω impedance • maximum network cable length 1200 meters Pin Function Multidrop Cables 1 RS-485 + Pin 1 Data 2 RS-485 - and 3 N.C. Power Supply 4 VDC – 5 VDC – 6 N.C. 7 VDC + 8 VDC + Data only Twisted Pair - Power supply RJ45 RJ45 RJ45 RJ45 VDC+ VDC- 8 8 VDC- 5 5 5 5 RS-485- 2 2 RS-485- 2 2
Inhaltszusammenfassung zur Seite Nr. 18
® POWERSCAN D8330/M8300 2.8.3 Network Termination The first and last cradles of the chain (the two ends of the bus) must be properly terminated. The cradle has an internal terminator that can be selected via jumper. For this selection you must open the device. No Termination Static Dynamic Terminator for Multidrop Network Static termination works for all network configurations. However, the network is always under load even when no data transmission takes place. Dynamic term
Inhaltszusammenfassung zur Seite Nr. 19
INSTALLATION ® 2.9 POWERSCAN M8300 BATTERY MAINTENANCE 2.9.1 Battery Charging ® Once the system is connected and powered, you can place the PowerScan M8300 into the cradle to charge the battery. When the reader is correctly inserted in the cradle, the "Reader" red LED on the cradle goes on to indicate that the battery is charging. The "Reader" green LED on the cradle goes on when the battery is completely charged. ® 2.9.2 Replacing PowerScan M8300 Batteries ® To change the
Inhaltszusammenfassung zur Seite Nr. 20
® POWERSCAN D8330/M8300 2.10 MOUNTING THE BC-80X0 / C-8000 CRADLE The cradle package contains the following items: BC-80X0 / C-8000 Cradle BC-80X0 Quick Reference / C-8000 Quick Reference BC-8000 Antenna 2 wall-mounting lock hinges 2 adhesive strips 4 rubber feet 1 horizontal base 1 inclined base The cradle (either BC-80X0 or C-8000) can be mounted for portable or fixed desktop usage, or it can be fixed to a wall. The horizontal base allows portable and fixed desktop
