Inhaltszusammenfassung zur Seite Nr. 1
TM
Magellan 1000i
On-Counter Presentation Omnidirectional Bar Code Reader
Product Reference Guide
Inhaltszusammenfassung zur Seite Nr. 2
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scan- ning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”). Owners of Datalogic products are hereby granted a non-exclusive, r
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents About This Manual ............................................................................................................... 1-1 Manual Conventions ....................................................................................................... 1-1 Connecting the Scanner ....................................................................................................... 1-2 Programming ..............................................................................
Inhaltszusammenfassung zur Seite Nr. 4
Wand Idle State ........................................................................................ 3-27 Signal Speed ............................................................................................ 3-28 Transmit Trailing Noise .............................................................................. 3-28 Transmit Leading Noise ............................................................................. 3-29 Symbology Conversion ............................................
Inhaltszusammenfassung zur Seite Nr. 5
Start/Stop Characters ...................................................................................................5-27 Code 39 Full ASCII .......................................................................................................5-28 Length Control .............................................................................................................5-29 Code 39 Length 1, Length 2 Programming Instructions ......................................................5-30 Quiet Z
Inhaltszusammenfassung zur Seite Nr. 6
Minimum Reads ........................................................................................................... 5-67 2D Symbologies ..................................................................................................................6-2 PDF 417 .......................................................................................................................6-2 Disable/Enable PDF 417 ............................................................................... 6-2 Le
Inhaltszusammenfassung zur Seite Nr. 7
Chapter 1 Getting Started ® The Magellan 1000i Omni-Directional Imaging Scanner offers hands-free scanning for small, easily handled items and handheld scanning for bulkier items. Its aggressive imaging perfor- mance and intuitive operation reduces user training and speeds checkout for better customer service. About This Manual This manual presents advanced user information which includes connection, programming, product and cable specifications, and other useful references. For additional
Inhaltszusammenfassung zur Seite Nr. 8
K e W y e b d o a g r d e Getting Started Connecting the Scanner The scanner kit you ordered to match your interface should provide a compatible cable for your installation. Use the appropriate instructions below to connect the scanner to the terminal, PC or other host device. Upon completing the connection via the appropriate interface instructions below, proceed to the Interface Related Features section of this manual and scan the barcode to select the correct interface type. RS-232 Seria
Inhaltszusammenfassung zur Seite Nr. 9
Programming Wand Emulation Connection — Connect the scanner to the appropriated port on the ter- minal/PC using the correct cable for the interface type you ordered. Reference Figure 2. IBM Connection — Connect the scanner to the IBM port on the terminal/PC using the cor- rect IBM cable. Reference Figure 2. Keyboard Wedge Connection — Before connection, turn off power to the terminal/PC. The Keyboard Wedge cable has a ‘Y’ connection from the scanner. Connect the female to the male end from the
Inhaltszusammenfassung zur Seite Nr. 10
Getting Started LED and Beeper Indicators The scanner’s beeper sounds and its green LED illuminates to indicate various functions or errors on the scanner. The tables below list these indications. One exception to the behaviors listed in the tables is that the scanner’s functions are programmable, and may or may not be turned on. For example, certain indications, such as the power-up beep can be disabled using programming barcode labels. Green LED Indications LED INDICATION COMMENT INDIC
Inhaltszusammenfassung zur Seite Nr. 11
Error Codes Error Codes Upon startup, if the scanner flashes its indicator LED or sounds an unexpected series of beep tones (other than normal power-up indications), this means the scanner has not passed its auto- 1 matic Selftest and has entered FRU isolation mode. If the scanner is reset or the trigger is pulled, the sequence will be repeated. The following table describes the LED flashes/beep codes associated with an error found. NUMBER OF LED FLASHES/ ERROR CORRECTIVE ACTION BEEPS 1 Conf
Inhaltszusammenfassung zur Seite Nr. 12
Getting Started NOTES ® 1-6 Magellan 1000i
Inhaltszusammenfassung zur Seite Nr. 13
Chapter 2 General Features Double Read Timeout The Double Read Timeout feature sets a time limit that determines how much time must pass before reading the same label again (e.g. two identical items in succession). START / END PROGRAMMING BARCODES 0.1 Second 0.2 Second 0.3 Second 0.4 Second DEFAULT 0.5 Second 0.6 Second Product Reference Guide 2-1
Inhaltszusammenfassung zur Seite Nr. 14
General Features Double Read Timeout — cont. START / END PROGRAMMING BARCODES 0.7 Second 0.8 Second 0.9 Second 1 Second ® 2-2 Magellan 1000i
Inhaltszusammenfassung zur Seite Nr. 15
Label Gone Timeout Label Gone Timeout This feature sets the time after the last label segment is seen before the scanner prepares for a new label. START / END PROGRAMMING BARCODES Sets the label gone timeout duration using hex values from 000 to 255 in increments of ten milliseconds (10ms or 0.01 seconds). To configure this feature, scan the “START/END” barcode above to place the unit in Programming Mode, then the “Set Label Gone Tim- eout,” followed by the three digits (zero padded) from the
Inhaltszusammenfassung zur Seite Nr. 16
General Features Sleep Mode This feature specifies the amount of time with no barcode reads before the scanner enters sleep mode. START / END PROGRAMMING BARCODES 15 Seconds 30 Seconds 1 Minute 2 Minutes 3 Minutes 4 Minutes 5 Minutes ® 2-4 Magellan 1000i
Inhaltszusammenfassung zur Seite Nr. 17
Sleep Mode Sleep Mode — cont. START / END PROGRAMMING BARCODES 6 Minutes 7 Minutes 8 Minutes 9 Minutes 10 Minutes DEFAULT 12 Minutes 15 Minutes 30 Minutes 1 Hour Product Reference Guide 2-5
Inhaltszusammenfassung zur Seite Nr. 18
General Features LED and Beeper Indicators Power On Alert Disables or enables the indication (a single beep) that the scanner has finished all its power up tests and is now ready for operation. START / END PROGRAMMING BARCODES Disable Enable DEFAULT ® 2-6 Magellan 1000i
Inhaltszusammenfassung zur Seite Nr. 19
LED and Beeper Indicators Good Read: When to Indicate This feature specifies when the scanner will provide indication (beep and/or flash its green LED) upon successfully reading a barcode. Choices are: � Good Read = Indicate after decode � Good Read = Indicate after transmit � Good Read = Indicate after CTS goes inactive, then active This option (Indicate after CTS goes inactive, then active), which uses CTS, is only valid for RS-232 inter- faces. NOTE START / END PROGRAMMING BARCODES After Dec
Inhaltszusammenfassung zur Seite Nr. 20
General Features Good Read Beep Control This feature enables/disables the scanner’s ability to beep upon a successful decode of a barcode. START / END PROGRAMMING BARCODES Disable Enable DEFAULT Good Read Beep Frequency Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/tone.) START / END PROGRAMMING BARCODES Low Medium DEFAULT High ³ 001 402 ® 2-8 Magellan 1000i
