Bedienungsanleitung Harbor Freight Tools 02623

Inhaltszusammenfassung zur Seite Nr. 1

®
1/2” AIR IMPACT
WRENCH
Model 02623
ASSEMBLY and OPERATING
INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
c ®
Copyright 2002 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353

Inhaltszusammenfassung zur Seite Nr. 2

Specifications Drive Size 1/2” Maximum RPM’s Forward 6600 RPM’s @90 PSI Maximum RPM’s Reverse 6800 RPM’s @90 PSI Maximum Torque 625 FT./LBS. Average Air Consumption 4.7 CFM at 90 PSI Air Inlet 1/4” - 18 NPT Maximum Air Pressure 90 PSI Blows Per Minute 1200 BPM Maximum Bolt Capacity 5/8” Weight 6.6 Lbs. Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagr

Inhaltszusammenfassung zur Seite Nr. 3

8. Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running machines or air hoses. 9. Maintain tools with care. Keep tools clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Disconnect a

Inhaltszusammenfassung zur Seite Nr. 4

Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be under- stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure the parts listed on page 6 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of

Inhaltszusammenfassung zur Seite Nr. 5

Operation (continued) Note: Turn off your air compressor and disconnect the air hose when you are changing sockets. After you attach the socket, attach the air hose and turn the air compressor on. 5. Select the appropriate size 1/2” socket for your needs. 6. Push and snap the socket (not included) onto the Anvil (#43). Tightening Note: Push Forward/Reverse Valve #9 to the left for clockwise rotation, push to the right for counterclockwise rotation. This is a sliding valve that is combined w

Inhaltszusammenfassung zur Seite Nr. 6

Parts List Part No. Description Qty. Part No. Description Qty. 1 Air Inlet 1 27 Cylinder Dowel 1 2 Throttle Valve Spring 1 29 Rotor Blade 6 4a Throttle Valve Assy. 1 30 Front End Plate 1 5a Throttle Valve Seat 1 31 Rear End Plate 1 6 Throttle Valve Pin 1 32 End Plate Gasket 1 7 Exhaust Deflector 1 33 Motor Clamp Washer 2 8 Trigger 1 34 Hammer Frame 1 9 Forward/Reverse Valve 1 35 Hammer Pin 2 11 0-ring 2 37 Hammer 2 12 Motor Housing Assy.

Inhaltszusammenfassung zur Seite Nr. 7

Assembly Drawing Page 7 SKU 02623