Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
3 - 4 5 - 9 10 11 12
Inhaltszusammenfassung zur Seite Nr. 3
Inhaltszusammenfassung zur Seite Nr. 4
Class D Topology IR2110S S/N 87dB at 15kW @ 1 ohm All "N" Channel MOSFET TO218 Transistors Unregulated Power Supply 140 Volt Rails +/- for INSANE Amounts of Power Capacitance Voltage 160V Monster Solid Copper Buss Bars to Pass >1000 Amps of Current Idle Current Draw 8 amps Maximum Current Draw >1400 amps Dual Monoblock Internally Bridged Digitally Controlled Module for Damping Factor >1000 @ 100Hz 200mV - 7.6V Input Sensitivity Short Circuit Speaker Protection Thermal Protection Optimized for a
Inhaltszusammenfassung zur Seite Nr. 5
SPECIFICATIONS Unique Protection Sensing Circuit for Maximum Power 2.5mm Thick PCB (57% thicker than normal 1.6mm) Over 83 Pounds! Comes with Plexiglass & Metal Bottoms Remote Bass Control Included 12 5/8" W x 2 3/4" T x 32 11/16" L Subsonic Filter 15-50Hz @ 24dB Per Octave Low-Pass X-over 40-275Hz @ 24dB Per Octave Bass Boost 40-120Hz, 0-18dB (4) 1/0 Gauge Power Input Terminals (4) 1/0 Gauge Ground Input Terminals (2) 8 Gauge Remote Turn-On Terminals (4) 8 Gauge Speaker Output Terminals Power
Inhaltszusammenfassung zur Seite Nr. 6
BRIDGED + + + + INPUT REMOTE L R BASS POWER GAIN SUBSONIC BOOST BASS EQ LPF [GREEN] PROTECT SPEAKER OUTPUT [RED] SPEAKER OUTPUT MIN MAX 10Hz 50Hz 0dB 18dB 40Hz 120Hz 35Hz 250Hz GND GND +12V +12V REM +12V +12V GND GND POWER INPUT 5
Inhaltszusammenfassung zur Seite Nr. 7
1.Input RCA jacks INPUT L R These inputs are for signal cables from the source. Always use high quality RCA cables. 2.Gain GAIN This control allows you to vary the amplifiers input sensitivity between 0.2[200millivolts]and 7.6volts. Clockwise rotation raises the threshold and lowers the sensitivity, requiring higher input signal voltage from the source. in order to obtain maximum output. counter-clockwise adjustment lowers the threshold and raises the sensitivity, requiring a lower source voltag
Inhaltszusammenfassung zur Seite Nr. 8
4.Bass Boost & EQ Control 40Hz 120Hz The Bass EQ control is used to select the boost frequency. Any frequency from 40 to 120 Hz can be selected. The Bass Boost control will increase the frequency selected from the Bass EQ up to 18dB. 5.LPF Control LPF 35Hz 250Hz This control is used to set desired low pass frequency[35 ~ 250Hz] The filter acts to cut-off frequencies above the set-point. 6.Remote Control input The Remote input can be connected to the Remote Dash Control with the supplied
Inhaltszusammenfassung zur Seite Nr. 9
7. LED indicatior POWER [GREEN] PROTECT [ ] RED POWER : This GREEN LED will illuminate when the amplifier is turned“ON”. If it fails to illuminate check the power connections to the amplifier and fuses. PROTECT : The amplifier protection circuitry will disable the amplifier if input overload, short circuit or extremely high temperature conditions are detected. when the protection mode is in operation the red LED indicator on the side panel will be illuminated the amplifier has gone into a self-
Inhaltszusammenfassung zur Seite Nr. 10
9.Power[Battery positive] +12V +12V Due to the power requirements of the amplifier this connection should be made directly to the positive [+] terminal of battery. For safety measure install an in-line fuse Holder [not included] as close to the battery positive [+] terminal as possible with an ampere rating not to exceed the maximum current specified on page 3 10. REM To remote wire from source unit. The amplifier is turned“ON” remotely when vehicle`s source unit is turned “ON” 9
Inhaltszusammenfassung zur Seite Nr. 11
BRIDGED + + + + INPUT REMOTE L R BASS GAIN SUBSONIC BOOST BASS EQ LPF POWER [GREEN] PROTECT SPEAKER OUTPUT [RED] SPEAKER OUTPUT MIN MAX 10Hz 50Hz 0dB 18dB 40Hz 120Hz 35Hz 250Hz 10
Inhaltszusammenfassung zur Seite Nr. 12
Turning on the Amplifier The amplifier automatically turns on within a few seconds after remote voltage is applied. If your system is set-up so that the source unit provides the remote voltage . Then it would turn on when your stereo is turn on. Note that there are alternate means of providing the 12 volt remote control signal. including and auxiliary switch. Adjusting The Audio Level As stated previously, it is important to obtain a close match between the source unit`s output voltage and The
Inhaltszusammenfassung zur Seite Nr. 13
12
