Inhaltszusammenfassung zur Seite Nr. 1
Samsung SmartCam
User Manual
SNH-1010N
Inhaltszusammenfassung zur Seite Nr. 2
SPECIFY SERVICE INSTRUCTIONS AND WARRANTY TERMS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE US
Inhaltszusammenfassung zur Seite Nr. 3
Contents • Never use the product near bath tub, sink, washing machine and in wet basement to avoid moisture. • The product is designed for indoor use. GETTING STARTED • The product is not designed for medical monitoring, and requires a grown-up’s protective supervision on its use. Key Features ………………………………………………… 4 • To avoid overheating of the product, do not expose the product to direct sunlight; do Basic Information …………………………………………… 6 not install or use near a heat source such as heater,
Inhaltszusammenfassung zur Seite Nr. 4
Key Features • Easy to install - With the help of WPS (WiFi Protected Setup), wireless sharing and easy connection are enabled. - Simply visit the home page (www.samsungsmartcam.com) and download and install the program without a separate installer program. • Remote monitoring - Whenever and wherever if you are in the Internet enabled environment, remote monitoring is ready for you. GettinG Started 01 - PC, laptop or smart phone can be used for monitoring. • Real-time alarm - Detect
Inhaltszusammenfassung zur Seite Nr. 5
Getting Started Product and Accessories Check for above components when opening the product package. 0 1 Camera Power Adaptor Quick Start Guide License Information Warranty Card Bracket Double-sided Tape Network Cable ` Please save the packaging. you will need the serial number later to register the camera. n
Inhaltszusammenfassung zur Seite Nr. 6
Basic Information Product At a Glance Front View High quality camera lens Built-in IR l EDs for night vision Power status l ED Red: Power On, Boot-up in process White: Camera ready Yellow: Privacy mode enabled WiFi status l ED Magenta: Updating firmware Flashing White: Searching for wireless network Steady White: Wireless network connected Built-in Mic Off: Connected via network cable Bottom View Holes for wall mount bracket Built-in speaker · English
Inhaltszusammenfassung zur Seite Nr. 7
Getting Started Side View 0 1 WPS Button Used to connect to the Wireless Access Point Press and hold for 3sec to initiate WPS mode Privacy Button Press for 3sec to stop transmitting video/audio Press and hold for 10sec to reset the camera to default settings Rear View DC 5V Power Input Network port Used if WPS is not supported on the Wireless Access Point or if you do not have a Wireless Access Point
Inhaltszusammenfassung zur Seite Nr. 8
Installation Precautions 1. Install the camera in a place where the WiFi signal can be reached and without interference. inStallation & 2. Keep it away from humidity such as around the humidifier. 3. Keep it away from the direct sunlight, strong light or dust; install it in a place network ConneCtion 02 with clear view. 4. Do not install it in a place where there are a lot of obstacles. 5. Keep the lens clean at all times. Wipe off the dust with a soft cloth. 6. S witching between day and
Inhaltszusammenfassung zur Seite Nr. 9
Installation & Network Connection Wall mounting Desktop mounting 1. Use a double-sided tape to secure the bracket to 1. Place the camera in a desired position a desired position. on the surface. ` You can use the screws to tighten the camera. (not n included) ` The double-sided tape cannot be reused after being 0 2 used once. 2. Adjust the camera’s shooting angle as appropriate. ` Keep the installation surface clean before attaching the double-sided tape to the bracket. Otherwise, the adhe
Inhaltszusammenfassung zur Seite Nr. 10
3. Adjust the camera’s shooting angle as appropriate (left and right) and 5. Plug in the power cable and arrange the cables through the bracket tighten the screws on the bottom of the bracket. holes. ` You can also use a coin or flat-head screwdriver to tighten them. ` When done, remove the protective film from the lens. n n Power Supply 4. Adjust the camera’s shooting angle (top Plug-in the camera power adapter to the wall outlet and connect the camera as and bottom). shown. ` Do not put ex
Inhaltszusammenfassung zur Seite Nr. 11
Installation & Network Connection Network Connection and Settings Precautions Connecting via network cable • The wireless network access may fail, depending on the communications environment. If you do not have a Wireless Access Point, you must connect the camera using LAN • For details about the network settings and password, contact your network cable directly to your home router. 0 2 administrator or service provider. • For a specific Internet service requiring user authentication, you may
Inhaltszusammenfassung zur Seite Nr. 12
Connecting via WiFi without WPS feature Conneting using WiFi WPS feature What is WPS? If you want to connect the camera using a non-WPS Wireless Access Point, change WPS enables to make connection between the camera and the Wireless Access the network setting to Wire and try the wireless network. Point with a simple click of the button. 1. When you apply the power, the power status LED is lit red, and it will change to white when the booting is completed. 1. Use the network cable (LAN cable)
Inhaltszusammenfassung zur Seite Nr. 13
Monitoring Registration Once you register the product with the site, you can monitor the camera video on the PC or laptop computer. Web browser requirements Windows Mac - Windows XP ,7 supported MonitorinG03 MAC OS X Snow Leopard or - Internet Explorer 8, 9 0 3 higher is supported (The 64-bit is not supported.) - Safari Registration 13 - Firefox - Mac Chrome, Firefox - Chrome Web browser requirements 13 Starting SmartCam 13 Starting SmartCam l ive Video 18 Monitoring options 19 1. From your
Inhaltszusammenfassung zur Seite Nr. 14
Plug in installation You need to install your plug in to automatically search for cameras connected 3) Click to begin the installation. to the network and view the video in your camera. ` If you login or click in a PC where the plug in is not n installed, the installation message window will pop up. ` When you install the plug in, the web browser will be terminated and you need to launch it again. 1) Click , run the setup file. 4) Installation
Inhaltszusammenfassung zur Seite Nr. 15
Monitoring For Mac 2) Click . 4) Enter password, and click . 0 3 3) Click . 5) Installation has completed. 1
Inhaltszusammenfassung zur Seite Nr. 16
5. Provide the requested information, and click . 6. According to the network connection and setting, click when the camera LED turns into White. 7. Select the serial number of the camera to be added from the camera search • ID: Create the user ID and click the . list. Fill in the user ID in 8 ~ 14 alphanumeric characters and ‘.’. If the camera is not found, enter the serial number manually. • P assword: C reate a password between 8 to 14 characters using both
Inhaltszusammenfassung zur Seite Nr. 17
Monitoring 9. Create and . 12. Select your Wireless Network from the list. 10. Click . 13. Enter the password of your Wireless Network and click . 0 3 Display Strings ` The camera password is used to block the unauthorized access to your camera. n ` Create camera password using alphanumeric characters between 1 to 8 without any space. ` If your Wireless Network is hidden, select . n ` To display the password, select
Inhaltszusammenfassung zur Seite Nr. 18
15. Unplug the network cable from the camera and the router. Live Video 16. Click if the button is activated. 1. Select a camera from the camera list at the upper left hand of the screen. 17. Once the camera is successfully registered, you can check the camera in the camera list. ` The gray icon indicates the camera is inactive so you cannot monitor it right now. n 2. Enter the camera password and click . ` Check to connect the camera without entering the c
Inhaltszusammenfassung zur Seite Nr. 19
Monitoring Item Description Monitoring options Enlarges current video to the maximum size of the monitor. Full screen 4 Supported by Internet Explorer only. 1 2 3 4 If you set Night Vision to , the camera will be automatically converted to Night Vision mode. If you set Night Vision to , the camera will not be 5 Night Vision converted to Night Vision mode, and it will operate in a color mode. I f it is converted to a black/white mode in the dark when Night Vision is , the IR
Inhaltszusammenfassung zur Seite Nr. 20
Network Speed Recommended Set up Profile Name Resolution Frame rate bandwidth Low Speed Network VGA 5 fps 768Kbps Basic Info Mid Speed Network VGA 10 fps 1Mbps High Speed Network VGA 20 fps 1.5Mbps ` What is Relay Mode? n Depending on your network connection, peer to peer connection may not be available. ` If you cannot make a peer to peer connection, the camera should be connected in relay mode. In this case, the video will be played for the first seven minutes, 1 and if you want to see
