Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
About the Manuals and Notations Used Types of Manual The documentation for your EPSON projector is divided into the following two manuals. Refer to the manuals in the order given below. Safety Instructions/Support and Service Guide This manual contains information on using the projector safely, and also includes a guide for warranty service, and a troubleshooting check sheet. Be sure to read this manual thoroughly before using the projector. User’s Guide (this manual) This User's Guide contain
Inhaltszusammenfassung zur Seite Nr. 3
Checking the Components When you unpack the projector, make sure that you have all these components. If any of the components are missing or incorrect, please contact the place of purchase. ❏ Projector (with lens cover) ❏ Remote control ❏ Power cable (3.0m) ❏ AA-size alkali batteries (2 pcs.) Connect to the projector and to a wall outlet. Insert into the remote control. Documentation ❏ Document CD-ROM (Safety Instructions/Support and Service Guide, User’s Guide) ❏ Quick Start Guide 1
Inhaltszusammenfassung zur Seite Nr. 4
Table of Contents ■ Features of the Projector.............................4 Remote control .................................................... 7 ■ Part Names and Functions..........................6 Rear...................................................................... 8 Front / Top ...........................................................6 Base ..................................................................... 8 Control panel........................................................6 ■
Inhaltszusammenfassung zur Seite Nr. 5
Table of Contents Troubleshooting ■ Problem Solving ........................................ 37 When the indicators provide no help ................. 39 •Problems relating to images................................. 39 Reading the indicators........................................37 •Problems when projection starts .......................... 43 •When the (warning) indicator is lit or •Problems with the remote control........................ 44 flashing...........................................
Inhaltszusammenfassung zur Seite Nr. 6
Features of the Projector Image appearance can be selected to match the projection environment (Color Mode) The optimum images for the location can be projected simply by selecting the desired color mode from the following five preset modes. p.18 Dynamic Living Room Cinema Color Mode Natural If "Natural", "Cinema" or "x.v.Color" is selected, the Epson Cinema Filter effect is applied automatically to increase the contrast and to make skin tones appear with more natural tints. p.18
Inhaltszusammenfassung zur Seite Nr. 7
Features of the Projector " " mode realizes more natural color reproduction This mode is compatible with the extended-gamut color space standard for video (xvYCC). Extended-gamut color images output by equipment supporting this standard are more faithful to the original, and the viewer can enjoy clearer, more natural images. p.18 Sophisticated color adjustment In addition to the "Color Mode", the absolute color temperature and skin tones can be adjusted by simple proced
Inhaltszusammenfassung zur Seite Nr. 8
Part Names and Functions Front / Top • Horizontal lens adjustment • Remote control light- dial p.16 receiving area p.13 Turn the dial to move the position of the • Top control panel Receives signals from the projection image to the left or right. See below remote control. • Lamp cover p.48 • Vertical lens adjustment Open this cover when replacing the dial p.16 lamp inside. Turn the dial to move the position of the projection image up or down. • Zoom ring p.16 • Side control panel Adjusts
Inhaltszusammenfassung zur Seite Nr. 9
Part Names and Functions Remote control • Remote control light-emitting area p.13 Outputs remote control signals. • Power button p.14, 15 Turns the projector power on/off. • Illumination button Illuminates all of the buttons on the remote control for 10 seconds so • Source buttons p.15 that they can be seen in dark Switch between equipment places. connected to the projector. • Default button p.26 • Esc button Restores default settings when p.18, 20, 26 menu is displayed. Returns to the pre
Inhaltszusammenfassung zur Seite Nr. 10
Part Names and Functions Rear • [S-Video] input port p.12 • [PC] input port p.12 • [RS-232C] port Connects to the S-Video out ports Connects to the RGB out Connects to a computer using an RS-232C of the video equipment. port of the computer. cable to control the projector from the computer. This is not used in normal use. • [Video] input port p.12 • Lamp cover open switch p.48 Connects to the Composite Video Press to open the lamp cover. output port of the video equipment. • [Trigger out] por
Inhaltszusammenfassung zur Seite Nr. 11
Appearance Center of lens 136 148.3 * 72 4.5 12.3 131 450 * Distance from center of lens to suspension bracket fixing point 300 75 150 Center of lens 56 45 134.7 389.7 160 5-M4 ×9 Units: mm 9
Inhaltszusammenfassung zur Seite Nr. 12
100" 100" Setting up Adjusting the projection size When the projector is further away from the screen, the projection image size are larger. While referring to the table below, position the projector so that the images are projected onto the screen at the optimum size. The values should be used as a guide for setting up the projector. Screen size Screen A* 90 Adjusting the projection size Center of lens B* *This is the distance from the center of the lens to the bottom of the projection imag
Inhaltszusammenfassung zur Seite Nr. 13
Setting up Projection methods If you are installing the projector on the ceiling, this projector should be installed by qualified technicians using only approved mounting equipment. If installation work is not carried out correctly, the projector could fall down. This may result in injury or accidents. Contact your dealer to carry out the installation work. If you use a ceiling mount and apply adhesives to the mount to prevent the screws from loosening, or if you use lubricants or oils on th
Inhaltszusammenfassung zur Seite Nr. 14
Connecting Image Sources • Turn the power off for both the projector and the signal source before connecting them. If the power for either device is on at the time of connection, damage may result. • Check the shapes of the cable connectors and the device ports before making the connections. If you try to force a connector to fit a device port with a different shape or number of terminals, a malfunction or damage to the connector or port may result. Video equipment (VHS VCR, DVD player, game
Inhaltszusammenfassung zur Seite Nr. 15
Preparing the Remote Control Inserting batteries into the remote control At the time of purchase, the batteries are not inserted into the remote control. Insert the supplied batteries before using the remote control. Lift up the battery cover while pressing its tab. Insert the batteries in the correct direction. Check the (+) and (-) indications inside Close the cover. the battery compartment and insert the batteries so that they face correctly. If delays in the responsiveness of the remo
Inhaltszusammenfassung zur Seite Nr. 16
Starting and Stopping Projection Turning the power on and projecting images Do not look into the lens while projection is in Remove the lens cover. progress. Turn the power on. Control Panel Remote Control Connect the (Commercially- power cable. Turn the power on for the available) connected equipment. Turn on the main power switch. ON If there is a problem with projection even though the projector is set up and connected correctly, refer to p.15, 37. If you set the "Direct Power On"
Inhaltszusammenfassung zur Seite Nr. 17
Starting and Stopping Projection When the expected images are not projected If more than one signal source has been connected, or if no images are projected, use the remote control or the projector's control panel buttons to select the signal source. For video devices, press the [Play] button on the video equipment first, then select the signal source. Using the remote control Using the control panel When the expected images are not projected Turning the power off When you press , th
Inhaltszusammenfassung zur Seite Nr. 18
Adjusting the Projection Screen Focus adjustment Focus adjustment Focus adjustment Focus adjustment Focus adjustment Focus adjustment Focus adjustment Focus adjustment Focus adjustment Focus adjustment Turn the focus ring to adjust the focus. Projection size adjustment (Zoom adjustment) Turn the zoom ring to adjust the size of the projected image. Focus adjustment Projection size adjustment (Zoom Wide adjustment) Tele Projection image position adjustment (Lens shift) Projection image position
Inhaltszusammenfassung zur Seite Nr. 19
Adjusting the Projection Screen Adjusting the tilt of the projector When an image from the projector that is placed on a flat surface is tilting horizontally ( ), use the front feet to correct the tilt. Extend Retract Extend Retract Adjusting the tilt of the projector Displaying a test pattern You can use a test pattern to make the first setup such as zoom, focus, and image position using the lens Displaying a test pattern shift without connecting to any electrical equipment. If
Inhaltszusammenfassung zur Seite Nr. 20
Basic Image Quality Adjustments Selecting the color mode Selecting the color mode Press and select the Inputting a signal to the color mode from the menu. HDMI1/HDMI2 terminals. Setting is also possible using the configuration menu. Selecting the aspect Selecting the aspect Press and select the aspect mode from the menu. Select Menu Operations When 720p, 1080i or 1080p signals are being Use to select an item. Press input to the [HDMI1], [HDMI2] or
