Inhaltszusammenfassung zur Seite Nr. 1
R
PXI-H990
TM
Multimedia Manager
Guide for Installation and Connections English
Guide d’installation et de connexions Français
Guía de instalación y conexiones
Español
Español
Italiano
Svenska
Inhaltszusammenfassung zur Seite Nr. 2
R ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U.S.A. Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. 7300 Warden Ave., Suite 203, Markham, Ontario L3R 9Z6, Canada Phone 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD. 6-8 Fiveways Boulevarde Keysborough, Victoria 3173, Australia Phone 03-9769-000
Inhaltszusammenfassung zur Seite Nr. 3
PRECAUTIONS GUIDE FOR INSTALLATION AND CONNECTIONS • Please read this GUIDE FOR INSTALLATION AND CONNECTIONS and the OWNER’S MANUAL thoroughly to familiarize yourself with each control and function. We at ALPINE hope that your new PXI-H990 will give you many years of listening enjoyment. In case of problems when installing your unit, please contact your authorized ALPINE dealer. Points to Observe for Safe Usage • Read this manual carefully before starting operation and use this system safely. We
Inhaltszusammenfassung zur Seite Nr. 4
DO NOT DAMAGE PIPE OR WIRING WHEN DRILLING HOLES. When drilling holes in the chassis for installation, take precautions so as not to contact, damage or obstruct pipes, fuel lines, tanks or electrical wiring. Failure to take such precautions may result in fire. DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS. Bolts or nuts used for the brake or steering systems (or any other safety-related system), or tanks should NEVER be used for installations or ground conn
Inhaltszusammenfassung zur Seite Nr. 5
Precautions • Be sure to disconnect the cable from the (–) battery post before installing your PXI-H990. This will reduce any chance of damage to the unit in case of a short-circuit. • Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage to the vehicle’s electrical system. • When making connections to the vehicle’s electrical system, be aware of the factory installed components (e.g. on-board computer). Do not tap in
Inhaltszusammenfassung zur Seite Nr. 6
Contents PRECAUTIONS 2 Accessories 6 Installation 7 Connections 10 Examples of system expansion 12 IMPORTANT Please record the serial number of your unit in the space provided below and keep it as a perma- nent record. The serial number plate is located on the bottom of the unit. SERIAL NUMBER: INSTALLATION DATE: INSTALLATION TECHNICIAN: PLACE OF PURCHASE: To prevent external noise from entering the audio system. • Locate the unit and route the leads at least 10 cm away from the car harness. • K
Inhaltszusammenfassung zur Seite Nr. 7
Accessories IONBUS cable (6m) DVD Audio Link cable (6m) Tapping screws (M4 x 14) x 4 Microphone (6m) Microphone terminal connec- Hexagonal wrench (M3) 1 * tion cable (6m) 2 * Bracket Bracket pan head screws Cord clamp 2 * (M4 x 8) x 8 x 4 Ferrite Core x 2 *1 Used only when setting the microphone built in the monitor (TMI-M990, sold separately) as the Road EQ microphone. *2 Use when mounting two PXI-H990s together. • Ferrite Core Attach the Ferrite Core (included) to the both ends of the IONBUS c
Inhaltszusammenfassung zur Seite Nr. 8
Installation • Mounting the base unit 1. Decide on the installation location. • The trunk, etc., is the best place. 2. Mark the positions of the mounting screws at the chosen location. 3. Drill 3 mm (1/8”) holes or smaller. WARNING: When making holes, be careful not to damage pipes, tanks, electric wires, etc. Doing so could lead to accidents or fire. 4. Securely mount the unit using the four included tapping screws (M4 x 14). Tapping screws (M4 x 14) 7-EN
Inhaltszusammenfassung zur Seite Nr. 9
< Setting up two PXI-H990s > Find a location that can accommodate both unit together then proceed with the following proce- dure. To set up two PXI-H990s, first connect both base units before setting them up. 1. Remove the feet from the base unit sides that have no terminals. One screw holds each foot in place. Foot 2. Remove the screw from the top part of one base unit marked with using the supplied hexagonal wrench (M3). Reverse the direction of the plate and re-attach it as shown below. Bef
Inhaltszusammenfassung zur Seite Nr. 10
3. Place two base units side by side, and attach the brackets with the supplied bracket pan head screws (M4 x 8). Bracket pan head screw (M4 x 8) 4. Refer to “Mounting the base unit” on page 7, and firmly attach the base. When using two PXI-H990s, change the System switch on the base unit to Memo “DUAL”. (For Basic Connections Diagram, refer to page 10) • Mounting Microphone Mounting Location Mount the microphone on the rear-view mirror, headrest, sun visor, or other appropriate location. • We r
Inhaltszusammenfassung zur Seite Nr. 11
Connections • Basic Connections Diagram < Top view > Normally the various Memo indicators are lit blue. Dolby digital indicator Lights red during Dolby Digital decoding. DTS indicator Lights up red during DTS decoding. LPCM indicator Lights up red when LPCM (MLP Lossless or CD-DA) input. Road EQ Indicator Lights up red when Road EQ is ON. Remove the screw marked using the included Memo hexagonal wrench (M3). < Base section > REAR DUAL FRONT SINGLE System switch • Set to SINGLE when con- nect
Inhaltszusammenfassung zur Seite Nr. 12
< Side Panel > Connect to: Terminal specification • DVD Audio Link terminal Connect to the DVD Audio Terminal for DVD audio playback. terminal of the DVI-9990 head unit, etc., using the DVD Audio Link cable. • Microphone terminal Connect to the microphone Connect microphone. (supplied with the main unit) or Connect to the microphone terminal with the supplied microphone the separately sold monitor terminal connection cable when using the separately sold monitor (TMI-M990) Road EQ (TMI-M990) inte
Inhaltszusammenfassung zur Seite Nr. 13
Examples of system expansion • PXI-H990 + DVI-9990 Head Unit + External Amplifier + Video etc. DVD Audio Link cable DVD Audio Link cable System switch (Included) (Included) REAR DUAL FRONT SINGLE To DVD Audio To DVD Audio To DVD Audio To DVD Audio Set to REAR Link terminal Link terminal Link terminal Link terminal IONBUS compatible head unit (sold separately) DVI-9990 *1 Audio output Audio output *1 *1 terminal terminal *1 To external To external amplifier (refer amplifier (refer to page 11) to
Inhaltszusammenfassung zur Seite Nr. 14
• PXI-H990 + DVI-9990 Head Unit + TMI-M990 Monitor + Ai-NET compatible Changer Connected To IONBUS DVI-9990 terminal IONBUS TMI-M990 compatible head IONBUS cable *1 *1 IONBUS unit (sold compatible separately) To S video input monitor (sold terminal To S video separately) To DVD Audio Link terminal output terminal S video cable (Supplied with the head unit) To IONBUS terminal DVD Audio Link cable *1 (Included) *2 Microphone terminal connection cable (Included) System switch 1:SYSTEM To microphone
Inhaltszusammenfassung zur Seite Nr. 15
Inhaltszusammenfassung zur Seite Nr. 16
