Inhaltszusammenfassung zur Seite Nr. 1
MITSUBISHIELECTRIC
Motion Controllers
Programming Manual
Common
Q173DCPU
Q172DCPU
01 01 2008
INDUSTRIAL AUTOMATION
MITSUBISHIELECTRIC
B(NA)-0300134
Version A
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY PRECAUTIONS (Please read these instructions before using this equipment.) Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly. These precautions apply only to this product. Refer to the Q173DCPU/Q172DCPU Users manual for a description of the Motion controller safety precautions. In this manual, the safety instructions are ranked as "DANGER" and "CA
Inhaltszusammenfassung zur Seite Nr. 3
For Safe Operations 1. Prevention of electric shocks DANGER Never open the front case or terminal covers while the power is ON or the unit is running, as this may lead to electric shocks. Never run the unit with the front case or terminal cover removed. The high voltage terminal and charged sections will be exposed and may lead to electric shocks. Never open the front case or terminal cover at times other than wiring work or periodic inspections even if the power is OFF. The i
Inhaltszusammenfassung zur Seite Nr. 4
3. For injury prevention CAUTION Do not apply a voltage other than that specified in the instruction manual on any terminal. Doing so may lead to destruction or damage. Do not mistake the terminal connections, as this may lead to destruction or damage. Do not mistake the polarity ( + / - ), as this may lead to destruction or damage. Do not touch the heat radiating fins of controller or servo amplifier, regenerative resistor and servomotor, etc., while the power is ON and for
Inhaltszusammenfassung zur Seite Nr. 5
CAUTION The dynamic brakes must be used only on errors that cause the forced stop, emergency stop, or servo OFF. These brakes must not be used for normal braking. The brakes (electromagnetic brakes) assembled into the servomotor are for holding applications, and must not be used for normal braking. The system must have a mechanical allowance so that the machine itself can stop even if the stroke limits switch is passed through at the max. speed. Use wires and cables that ha
Inhaltszusammenfassung zur Seite Nr. 6
CAUTION Use the program commands for the program with the conditions specified in the instruction manual. Set the sequence function program capacity setting, device capacity, latch validity range, I/O assignment setting, and validity of continuous operation during error detection to values that are compatible with the system application. The protective functions may not function if the settings are incorrect. Some devices used in the program have fixed applications, so use th
Inhaltszusammenfassung zur Seite Nr. 7
CAUTION The Motion controller, servo amplifier and servomotor are precision machines, so do not drop or apply strong impacts on them. Securely fix the Motion controller, servo amplifier and servomotor to the machine according to the instruction manual. If the fixing is insufficient, these may come off during operation. Always install the servomotor with reduction gears in the designated direction. Failing to do so may lead to oil leaks. Store and use the unit in the followin
Inhaltszusammenfassung zur Seite Nr. 8
(4) Wiring CAUTION Correctly and securely wire the wires. Reconfirm the connections for mistakes and the terminal screws for tightness after wiring. Failing to do so may lead to run away of the servomotor. After wiring, install the protective covers such as the terminal covers to the original positions. Do not install a phase advancing capacitor, surge absorber or radio noise filter (option FR-BIF) on the output side of the servo amplifier. Correctly connect the output side (
Inhaltszusammenfassung zur Seite Nr. 9
(6) Usage methods CAUTION Immediately turn OFF the power if smoke, abnormal sounds or odors are emitted from the Motion controller, servo amplifier or servomotor. Always execute a test operation before starting actual operations after the program or parameters have been changed or after maintenance and inspection. Do not attempt to disassemble and repair the units excluding a qualified technician whom our company recognized. Do not make any modifications to the unit. Keep
Inhaltszusammenfassung zur Seite Nr. 10
(7) Corrective actions for errors CAUTION If an error occurs in the self diagnosis of the Motion controller or servo amplifier, confirm the check details according to the instruction manual, and restore the operation. If a dangerous state is predicted in case of a power failure or product failure, use a servomotor with electromagnetic brakes or install a brake mechanism externally. Use a double circuit construction so that the electromagnetic brake operation circuit can be ope
Inhaltszusammenfassung zur Seite Nr. 11
CAUTION When replacing the Motion controller or servo amplifier, always set the new module settings correctly. When the Motion controller or absolute value motor has been replaced, carry out a home position return operation using one of the following methods, otherwise position displacement could occur. 1) After writing the servo data to the Motion controller using programming software, switch on the power again, then perform a home position return operation. 2) Using the backu
Inhaltszusammenfassung zur Seite Nr. 12
REVISIONS The manual number is given on the bottom left of the back cover. Print Date Manual Number Revision Jan., 2008 IB(NA)-0300134-A First edition Japanese Manual Number IB(NA)-0300126 This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the conten
Inhaltszusammenfassung zur Seite Nr. 13
INTRODUCTION Thank you for choosing the Mitsubishi Motion controller Q173DCPU/Q172DCPU. Before using the equipment, please read this manual carefully to develop full familiarity with the functions and performance of the Motion controller you have purchased, so as to ensure correct use. CONTENTS Safety Precautions.................................................................................................................................. A- 1 Revisions......................
Inhaltszusammenfassung zur Seite Nr. 14
3.1.3 Individual parameters........................................................................................................................ 3-10 3.2 I/O number assignment..................................................................................................................... 3-15 3.2.1 I/O number assignment of each module .......................................................................................... 3-15 3.2.2 I/O number of each CPU modules ..............
Inhaltszusammenfassung zur Seite Nr. 15
About Manuals The following manuals are also related to this product. In necessary, order them by quoting the details in the tables below. Related Manuals (1) Motion controller Manual Number Manual Name (Model Code) Q173DCPU/Q172DCPU Motion controller User's Manual This manual explains specifications of the Motion CPU modules, Q172DLX Servo external signal interface module, Q172DEX Synchronous encoder interface module, Q173DPX Manual pulse generator interface IB-0300133
Inhaltszusammenfassung zur Seite Nr. 16
(2) PLC Manual Number Manual Name (Model Code) QCPU User's Manual (Hardware Design, Maintenance and Inspection) This manual explains the specifications of the QCPU modules, power supply modules, base modules, SH-080483ENG (13JR73) extension cables, memory card battery and others. (Optional) QCPU User's Manual (Function Explanation, Program Fundamentals) This manual explains the functions, programming methods and devices and others to create programs SH-080484ENG (13JR74)
Inhaltszusammenfassung zur Seite Nr. 17
MEMO A - 16
Inhaltszusammenfassung zur Seite Nr. 18
1 OVERVIEW 1. OVERVIEW 1 1.1 Overview This programming manual describes the common items of each operating system software, such as the Multiple CPU system of the operating system software packages "SW8DNC-SV Q " for Motion CPU module (Q173DCPU/Q172DCPU). In this manual, the following abbreviations are used. Generic term/Abbreviation Description Q173DCPU/Q172DCPU or Q173DCPU/Q172DCPU Motion CPU module Motion CPU (module) Q172DLX Servo external signals interface modul
Inhaltszusammenfassung zur Seite Nr. 19
1 OVERVIEW REMARK For information about the each module, design method for program and parameter, refer to the following manuals relevant to each module. Item Reference Manual Motion CPU module/Motion unit Q173DCPU/Q172DCPU User’s Manual PLC CPU, peripheral devices for PLC program design, I/O Manual relevant to each module modules and intelligent function module Operation method for MT Developer Help of each software • Design method for Motion SFC program Q173DCPU/Q172DCP
Inhaltszusammenfassung zur Seite Nr. 20
1 OVERVIEW 1.2 Features The Motion CPU and Multiple CPU system have the following features. 1.2.1 Features of Motion CPU (1) Q series PLC Multiple CPU system (a) Load distribution of processing can be performed by controlling the complicated servo control with Motion CPU and the machine control or information control with PLC CPU. Therefore, the flexible system configuration can be realized. (b) The Motion CPU and PLC CPU are selected flexibly, and the Multiple CPU
