Inhaltszusammenfassung zur Seite Nr. 1
OPERATING GUIDE for your
GEM-K1CA KEYPAD
GEMINI
SYSTEM READY
09/15/05 12:05 AM
NEXT / YES
R 1 2 3 P
U
PRIOR / NO
B 4 5 6 Q
AREA
G
C 7 8 9 0
COMPUTERIZED SECURITY SYSTEM
© NAPCO 2005 OI279D 5/05
1
STATUS
ARMED
Inhaltszusammenfassung zur Seite Nr. 2
INTRODUCTION The GEM-K1CA is a “smart” user- Regardless of how your system has future reference. Check the Glossary friendly, interactive menu-driven keypad for an explanation of terms that may be been configured, rest assured that it has designed for your Napco control panel. unfamiliar to you. been carefully designed and engineered Its alphanumeric screen will not only to the highest industry standards. To You'll probably find subjects display the status of your system, but assur
Inhaltszusammenfassung zur Seite Nr. 3
TABLE OF CONTENTS TO SILENCE AN ALARM, ENTER YOUR TABLE OF CONTENTS CODE, AND PRESS U. Section Page FOR SERVICE, CALL: _____________________ KEYPAD CONTROLS & INDICATORS ............................................4 CENTRAL STATION: _____________________ ARMING AWAY: SETTING THE ALARM WHEN LEAVING ............6 EXIT DELAY: ___________________________ ARMING STAY: PROTECTING YOURSEL
Inhaltszusammenfassung zur Seite Nr. 4
KEYPAD CONTROLS & INDICATORS 1 GEMINI 2 SYSTEM ARMED 09/01/05 12:00 AM 3 7 8 R P 1 2 3 4 U 9 B 4 5 6 Q 5 10 C 7 8 9 0 6 G 11 COMPUTERIZED SECURITY SYSTEM 12 4 ARMED STATUS
Inhaltszusammenfassung zur Seite Nr. 5
KEYPAD CONTROLS & INDICATORS Window. Displays system status (2) Unbypasses a bypassed zone the window display. 1 messages, zone descriptions, etc. (GEM-P3200/9600 panels only). 10 AWAY Button. (1) Arms all zones 2 STATUS Light. Lights (green) to RESET Button. (1) Resets in the system, with display 6 indicate that the system is ready various system troubles, displays, indicating the exit time remaining. for arming. If a zone is not etc. (See text.) (2) Resets (2) Scrolls window display
Inhaltszusammenfassung zur Seite Nr. 6
ARMING AWAY: SETTING THE ALARM WHEN LEAVING Arming the System SYSTEM READY 1 Check the keypad. The green STATUS light must be on in order to arm. If the green light is off, “ZONES FAULTED” will display in the window followed by the number and description of each faulted zone. Note each problem zone and EXIT TIME 060 secure it by closing a window, door, etc. When all zones are secure, the green PLEASE LEAVE NOW STATUS light will come on and the window will display “SYST
Inhaltszusammenfassung zur Seite Nr. 7
ARMING AWAY: SETTING THE ALARM WHEN LEAVING System Trouble SYSTEM TROUBLE If you attempt to arm with a “SYSTEM TROUBLE” display alternating with an indicated trouble code (e.g. “E02-00” (low battery); see SYSTEM TROUBLE ERROR CODES), a 3-second tone will SYS/TRBL sound at the keypad. The window will display “CAN'T ARM SYSTEM, PRESS RESET KEY”. If you cannot correct the problem immediately, pressing C will enable you to arm in this LOW BATTERY condition. Be sure to call for se
Inhaltszusammenfassung zur Seite Nr. 8
ARMING STAY: PROTECTING YOURSELF AT HOME Arming in STAY Mode BYPASSED ARMED STAY Interior Zones, when bypassed, allow free movement within the home while the protection of armed perimeter zones is maintained. To bypass Interior Zones, enter your User Code and press P. Instant Protection SYSTEM ARMED I When retiring for the evening, after all family members are home, you can cancel the entry delay on the Entry Zone(s). P To arm with instant protection, pr
Inhaltszusammenfassung zur Seite Nr. 9
ARMING STAY: PROTECTING YOURSELF AT HOME Easy Exit (Optional - Easy Exit programmed? YES NO) Your system may have been programmed for Easy Exit, which allows a user to exit the premises while the system is armed STAY. By activating Easy Exit while the system is armed STAY, the Exit Delay countdown will take place, during which time you are permitted to leave through the exit door. The Easy Exit Delay time will be identical to the Exit Delay time the system gives you each time
Inhaltszusammenfassung zur Seite Nr. 10
TURNING OFF THE ALARM (DISARMING) WHEN RETURNING Disarming the System DISARM SYSTEM 1 Enter your premises through the Entry/Exit door. The keypad will sound a steady tone to ENTRY TIME XXX remind you to disarm the system before your Entry Delay time expires. 2 Enter your User Code and press U. The red ARMED light will go out, indicating that the system has been disarmed. If you enter an invalid code, the keypad will beep 4 times, INVALID ENTRY signifying an error. Re-e
Inhaltszusammenfassung zur Seite Nr. 11
FIRE PROTECTION (Applicable only where local ordinance permits use of this alarm control panel for fire protection.) Fire-Zone Alarm FIRE FIRE ALARM If a fire is detected, “FIRE ALARM” will be displayed and the keypad sounder will pulse. 1. If a fire is in progress, evacuate the premises immediately! If necessary, call the Fire Department from an outside phone. 2. Press the C button to silence the keypad sounder. 3. If there is no evidence of a fire, enter your User Code an
Inhaltszusammenfassung zur Seite Nr. 12
FIRE PROTECTION closed. alternate route through the window. If Preparing a Fire Escape Plan Even with the most advanced fire alarm 2. One person sounds the alarm. the door is cool, brace your shoulder system, adequate protection requires an 3. Each person tests his door. against it and open it cautiously. Be escape plan. 4. Pretend the door is hot and use the ready to slam the door if smoke or alternate escape exit. heat rushes in. Crawl through smoke, To prepare your plan, draw fl
Inhaltszusammenfassung zur Seite Nr. 13
FIRE PROTECTION Floorplan Draw a plan of your premises in the space provided below. Floorplan 13
Inhaltszusammenfassung zur Seite Nr. 14
FIRE PROTECTION LIMITATIONS OF FIRE ALARM WARNING SYSTEM Although a fire alarm system may be of a reasons: (a) they may not sense fires that radio, air conditioner, or other appliance, or reliable and state-of- the-art design, neither it start where smoke cannot reach them, such by passing traffic, etc. Alarm warning nor its peripheral detection devices can offer as in chimneys, walls, roofs, behind closed devices, however loud, may fail to warn the guaranteed protection against fire. Any s
Inhaltszusammenfassung zur Seite Nr. 15
FUNCTION MENU The keypad can provide access to a wide assortment of utility functions. The functions are displayed in a prompting “YES/NO” format. 1 To enter the Function Menu, press R. • In all UL-listed or high-security installations, a valid User Code must first be entered followed by R. 2 To skip a function, answer NO (Q) or R. 3 To select and execute a function, answer YES (P) or U. • Functions may be manually scrolled forward or backward using R and B, respectively. • To
Inhaltszusammenfassung zur Seite Nr. 16
FUNCTION MENU Activate Bell Test? Activates the alarm (while disarmed) for about 2 seconds and ACTIVATE performs a battery test. If the alarm does not sound, call for service. BELL TEST Y/N • If the battery is low, a “LOW BATTERY E02-00 SERVICE” will appear in the display indicating a low battery condition. Allow 24 hours for the battery to recharge. If the trouble continues, call for service. Display System Troubles? Displays 1- or 2-digit error code along with a descr
Inhaltszusammenfassung zur Seite Nr. 17
FUNCTION MENU Reset System Trouble? System troubles display and sound at the keypad. Correcting RESET the trouble will clear most indications, however the following error codes will require SYS TRBL Y/N manual reset: E13; E19; E20 and E22. (See SYSTEM TROUBLE ERROR CODES for a description of error codes.) Reset Sensor Watch Failure? (Sensor Watch programmed? YES NO). RESET Your system may have been programmed for Sensor Watch, a feature which SENSOR MS
Inhaltszusammenfassung zur Seite Nr. 18
FUNCTION MENU Activate Telephone Test? (Telephone Test programmed? YES NO). Sends a ACTIVATE communicator test to the central station. A communication failure will be indicated DIALER TEST Y/N at the keypad by a system trouble “E03-FAIL TO COMM” display. Repeat the test to attempt to correct a communication failure, as any successful communication will clear this display. Delay Arming 1-4 hours. (Not for UL-listed systems). Your system may be set to TO ARM IN 1-4 HRS
Inhaltszusammenfassung zur Seite Nr. 19
FUNCTION MENU Activate Program? Activates the Program Mode from Keypad No. 1. Note: This ACTIVATE feature is disabled while armed. (See PROGRAMMING USER CODES) PROGRAM Y/N Activate Download? For installer's use only. If accidentally enabled, press C ACTIVATE to exit. Note: This feature is disabled while armed. DOWNLOAD Y/N Relay Control? (Relay Control programmed? YES NO). RELAY Turns ON or OFF one or more programmed Relay Groups. Pres
Inhaltszusammenfassung zur Seite Nr. 20
CENTRAL STATION MONITORING Your alarm specialist may have Opening and/or Closing Reporting. arming (Closing Report), the central programmed your system to be Your system can notify the central station will acknowledge arming. monitored by a central station. The built- station every time it is disarmed or This will signal at the keypad as a in digital communicator can transmit armed. Any or all of up to 96 “ringback” beep. Note: If the emergency signals and status reports to different user
