Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
ULTRALINK UL2000M TABLE OF CONTENTS 1. INTRODUCTION ......................................................................................................... 4 1.1 Before you get started .......................................................................................................... 4 1.1.1 Shipment ...................................................................................................................... 4 1.1.2 Registration .................................................
Inhaltszusammenfassung zur Seite Nr. 4
ULTRALINK UL2000M 1. INTRODUCTION Thank you very much for expressing your confidence in the ULTRALINK Series by purchasing this unit. With the UL2000M from BEHRINGER, you have acquired a modern, high-performance wireless transmission system. Thanks to its amazing set of features, you can use the UL2000M in all situations in which the highest sound quality and mobility are a must, e.g. live concerts, events and video productions. Depending on your local wireless transmission regulations, you can
Inhaltszusammenfassung zur Seite Nr. 5
ULTRALINK UL2000M The interchangeable AC plugs can be swapped at any time, adapting to various socket types in different countries (Fig. 1.1). 1. Keep the button (A) on the front side of the power supply pressed to release the plug. Pull the plug out and let go of the button. 2. Insert a different plug into the power supply unit. The plug is securely snapped into place when you hear a click. Fig. 1.1: Swapping plugs on the switching power supply unit 1.1.4 Initial operation of the microphone T
Inhaltszusammenfassung zur Seite Nr. 6
Inhaltszusammenfassung zur Seite Nr. 7
ULTRALINK UL2000M COLOR CODE Each BEHRINGER ULTRALINK transmitter can be color-coded using a color ring; this way you can easily differentiate between multiple transmitters (set to different frequencies). To easily match a transmitter to a receiver, you can also attach color-coded strips to each receiver. ANTENNA Two bar antennae can be connected to the ANTENNA 1 and ANTENNA 2 connectors. 2.1.2 Display Fig. 2.2: Closeup of the ULR2000 display (antenna symbol) These two antenna symbols indicate w
Inhaltszusammenfassung zur Seite Nr. 8
Inhaltszusammenfassung zur Seite Nr. 9
ULTRALINK UL2000M 4. If a valid frequency value is set, press the SET button again. In the display, you are asked to enter where you want to save your settings. Depending on the basic settings (ch. 2.2.5), the ULR2000 asks you to enter a channel color (BLUE, RED, ...) or a channel number (CHAN1, CHAN2, ...). 5. A storage location can be selected by pressing the UP or DOWN buttons. 6. Press the SET button again to store your frequency at the location you selected.The procedure is now over, and
Inhaltszusammenfassung zur Seite Nr. 10
ULTRALINK UL2000M 2.2.4 AUTO MUTE If the transmitter is turned on, off, or is switched to another channel without first muting the receiver, or if the transmission drops out due to weak batteries, audible noise will result. Even if the noise limiter is enabled on the receiver (ch. 2.2.3), it still requires some time to react, and such noise can not be suppressed safely. To bridge this latency time, the ULR2000 offers a practical Auto Mute function: When the ULM2000 is being turned off, when you
Inhaltszusammenfassung zur Seite Nr. 11
ULTRALINK UL2000M are shown in the display again. Deactivating LOCK 1. Press the SET button. LOC ON is shown in the display. 2. Press the UP or DOWN button once to select LOCOFF. 3. Press the SET button confirm, hence deactivating the keylock function. The procedure is now over, and the basic settings are shown in the display again. 2.2.7 PRESET The ULR2000 lets you work with 4 presets, each with 8 channels. Factory presets (Presets 2, 3 and 4) In the ULR2000, there are 3 factory presets (eac
Inhaltszusammenfassung zur Seite Nr. 12
ULTRALINK UL2000M 3. ULM2000 MICROPHONE 3.1 Control elements In this chapter, different control elements of your ULM2000 will be described, explained in detail, and you will get useful information on how to use them. Fig. 3.1: ULM2000’s underside POWER To power the hand-held transmitter on or off, keep the POWER button pressed for at least 2 seconds. Briefly pressing the POWER button confirms your choices when entering values (refers to later chapters). Additionally, you can check the current tr
Inhaltszusammenfassung zur Seite Nr. 13
ULTRALINK UL2000M 1. Turn the selection switch to one of the positions 1 - 8, corresponding to the desired channel number. If a valid value is selected (i.e. neither 9 nor 0), the LED blinks quickly once as a confirmation. 2. Briefly press the POWER button. The LED blinks with medium tempo. The number of individual flashes within one cycle corresponds to the value/channel number selected on the selection switch. If an invalid channel number is selected (0 or 9), the channel selected last remain
Inhaltszusammenfassung zur Seite Nr. 14
ULTRALINK UL2000M 7. After a second blink pause, an additional blink code is given as a confirmation: A successfully stored frequency is signaled with 2 slow blinks. The transmitter leaves the programming mode. If the LED blinks quickly 5 times, the frequency was not stored. In this case, start anew with step 2. If no entry is made for more than 5 seconds (either on the selection switch or by pressing the POWER button), the LED blinks quickly 5 times, and the programming mode is aborted. 8. D
Inhaltszusammenfassung zur Seite Nr. 15
ULTRALINK UL2000M If no entry is made for more than 5 seconds (either on the selection switch or by pressing the POWER button), the LED blinks quickly 5 times, and the programming mode is aborted. 6. After a second brief blink break, an additional blink code is given as a confirmation: Successful loading of a preset is signaled with two slow blinks. The unit leaves the programming mode. If the preset could not be loaded, the LED blinks quickly 5 times. In this case, start anew with step 2. 7.
Inhaltszusammenfassung zur Seite Nr. 16
ULTRALINK UL2000M For the Auto Mute function to work, it has to be activated on both the transmitter and the receiver! Activating/deactivating the Auto Mute function 1. Engage MUTE. The transmitter can now be switched into the programming mode. 2. Turn the selection switch to 0 and confirm your selection by keeping the POWER switch pressed for 2 seconds. As a confirmation, the LED blinks slowly once and then once again with medium tempo. The transmitter is now in the programming mode and waits
Inhaltszusammenfassung zur Seite Nr. 17
ULTRALINK UL2000M If the receiver is not powered on, no status is indicated. Briefly pressing the POWER button will neither turn the transmitter on nor off! 3.3.2 Transmission frequency 1. Turn the selection switch to 9. The position of the MUTE switch is irrelevant. 2. Briefly press the POWER button. 3. Just like during programming, 6 blink medium-tempo codes indicate the individual digits that make up the transmission frequency. Individual codes are separated from one another by brief pauses.
Inhaltszusammenfassung zur Seite Nr. 18
Inhaltszusammenfassung zur Seite Nr. 19
Inhaltszusammenfassung zur Seite Nr. 20
