Inhaltszusammenfassung zur Seite Nr. 1
User’s Guide
Shop online at
omega.com
e-mail: info@omega.com
Flow Sensor with
For latest product manuals:
Polypropylene Body
omegamanual.info
ISO 9002
ISO 9001
CERTIFIED
CERTIFIED
CORPORATE QUALITY CORPORATE QUALITY
MANCHESTER, UK
STAMFORD, CT
Flow Sensor with Stainless Steel Body
FPR 200
Flow Sensor
Inhaltszusammenfassung zur Seite Nr. 2
® OMEGAnet Online Service Internet e-mail omega.com info@omega.com Servicing North America: U.S.A.: One Omega Drive, Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 Tel: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada Tel: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: ® U.S.A. and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA ® Customer Service: 1-800-622-2378 /
Inhaltszusammenfassung zur Seite Nr. 3
Introduction This manual is a service guide produced by the manufacturer. The manual provides specific procedures and/or illustrations for installa- tion, inspection, cleaning and filtration of all Omega FPR 200 flow sensors. When properly followed, these procedures will keep your flow sensor operating dependably for many years. It is important for operators and maintenance personnel to be safety conscience when operating or repairing equipment. Developing a thor- ough knowledge of the precautio
Inhaltszusammenfassung zur Seite Nr. 4
Illustration 1: Mounting Instructions Installation - Mechanical 1. The flow sensor has NPT (National Pipe Thread) plumbing con- nections. It is recommended that a paste type pipe sealant be used on these threads. [Teflon tape sealant can be used as long as it is applied in such a way that it will not enter the flow stream. Pieces of Teflon tape can wrap around the turbine and impede its rotation.] 2. The recommended mounting orientation would be any plane that will place the axis of the tur
Inhaltszusammenfassung zur Seite Nr. 5
4. It is recommended that the sensor be placed in such a position that the round access cover can be removed for cleaning and tur- bine servicing. It is also recommended that a union be placed near the sensor to allow easy removal. Note1: The flow sensor is a bi-directional measuring device. References to “inlet” and “outlet” refer to uni-directional systems. Installation - Electronic (4-20mA Only) The flow sensor circuit is a two-wire loop-powered design that transmits a 4-20mA signal that i
Inhaltszusammenfassung zur Seite Nr. 6
Apply the DC supply voltage directly across the sensor wires. If the LED does illuminate, the load is either: too great of imped- ance or an open circuit. If the LED does not illuminate, the sen- sor's lead wires or circuit are defective. 6. The installation should be complete. Installation - Electronic (0-5VDC Output Only) 1. Connect the red wire (pin 1 for units with the electronic disconnect option) from the sensor to the positive terminal of the 12-35 VDC power supply. 2. Connect the bl
Inhaltszusammenfassung zur Seite Nr. 7
Installation - Electronic (Pulse Output Only) The flow sensor pulse output circuit is a three-wire DC-powered design that transmits a frequency proportional to flow rate. The circuit operates on 5-24 VDC and will consume a maximum of 25 mA from the power supply. 1. Connect the red wire (pin 1 for units with the electronic disconnect option) from the sensor to the positive terminal of the 5-24VDC power supply. 2. Connect the black wire from the transmitter (pin 2 for units with the electronic
Inhaltszusammenfassung zur Seite Nr. 8
Installation - Electronic (Relay Output Only) 1. Connect the red wire from the sensor to the positive terminal of the 12-35 VDC power supply. 2. Connect the black wire from the transmitter to the negative terminal of the 12-35 VDC power supply. 3. (Versions with stainless steel sensor body only) Be sure to properly ground the flow sensor by using the ground screw shown in Illustration 2 to GROUND SCREW connect the sensor body Earth ground. This step may be unnecessary if the piping system t
Inhaltszusammenfassung zur Seite Nr. 9
Set Point Adjustment (Relay Output Only) 1) Adjust the flow rate through the line in which the flow sensor is installed to the rate that corresponds to the desired relay trip point. 2) If the red LED on the back side of the sensor is not illuminated, use a small flat bladed screwdriver to slowly turn the adjustment screw on the set point potentiometer counter-clockwise until the red LED illuminates. 3) If the red LED is already illuminated, turn the adjustment screw on the potentiometer clock
Inhaltszusammenfassung zur Seite Nr. 10
1. Relieve pressure in the piping system. 2. Remove the retainer ring that secures the turbine access cover. 3. Remove the access cover with a pliers, taking care not to damage the o-ring seal. 4. Pull out the turbine assembly and the shaft. 5. Inspect the shaft for things that may have wrapped around it. 6. Inspect the turbine bearing surface for wear and elongation. Replace as necessary. 7. Clean any rust off of the magnets that may have accumulated. 8. Reassemble the unit by placing the tur
Inhaltszusammenfassung zur Seite Nr. 11
Mechanical Specifications FLOW SENSOR WITH STAINLESS STEEL BODY Maximum pressure: 200 PSI clear cover, 500 PSI SS cover º Maximum temperature: 225 F Measuring range* 1/2" NPT Ported: 0.5 - 15 GPM 3/4" & 1" NPT Ported: 1.5 - 50 GPM Wetted materials: 316SS, acetal copolymer, Buna, PEEK and polycarbonate ® Non-wetted materials: Epoxy, Lexan and PVC FLOW SENSOR WITH POLYPROPYLENE BODY Maximum pressure: 150 PSI º Maximum temperature: 150 F Measuring range* 1/2" NPT Ported:: 0.5 - 15 GPM Wetted ma
Inhaltszusammenfassung zur Seite Nr. 12
ALL VERSIONS WITH 0-5 VDC CIRCUIT Power requirements: 12-35VDC, 20 mA Maximum Current: 30 mA DC Max. Trans. Distance: <200 feet recommended Min. Load Resistance: 1000 Ω Flow rate accuracy: 2% of full scale Repeatability: 0.5% of scale Resolution: infinite Response time: 2 seconds to 90% ALL VERSIONS WITH PULSE OUTPUT CIRCUIT Power requirements: 5-24VDC, 20 mA Maximum Current: 25 mA DC Max. Trans. Distance: <200 feet recommended Flow rate accuracy: 2% of full scale Linearity: 0.5% of scale Resolu
Inhaltszusammenfassung zur Seite Nr. 13
Dimension Drawings DIM 1/2" NPTF Ports 3/4" & 1" NPTF Ports A 1.94" (49 mm) 3.06" (78 mm) B 1.13" (29 mm) 1.33" (34 mm) C 2.00" (51 mm) 2.46" (62 mm) D 2.45" (62 mm) 2.78" (71 mm) 1 D 2.60" (66 mm) 2.88" (73 mm) E 3.70" (94 mm) 5.25" (133 mm) F 2.63" (67 mm) 3.80" (97 mm) 2 F 3.38" (86 mm) n/a 1 Dimension with optional clear cover installed 2 Polypropylene version only (13)
Inhaltszusammenfassung zur Seite Nr. 14
NOTES: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Inhaltszusammenfassung zur Seite Nr. 15
WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product. If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department w
Inhaltszusammenfassung zur Seite Nr. 16
Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course! Shop online at omega.com TEMPERATURE Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies Wire: Thermocouple, RTD & Thermistor Calibrators & Ice Point References Recorders, Controllers & Process Monitors Infrared Pyrometers PRESSURE, STRAIN AND FORCE Transducers & Strain Gages Load Cells & Pressure Gages Displacement Transducers Instrumentation & Accesso
