Inhaltszusammenfassung zur Seite Nr. 1
PowerView ™
Model PV-101
User’s Guide
Rev 09-10-08 00-02-0605
Catalog Section 78
Inhaltszusammenfassung zur Seite Nr. 2
In order to consistently bring you the highest quality, full featured products, we reserve the right to change our specifications and designs at any time. The latest version of this manual can be found at www.fwmurphy.com. Warranty - A limited warranty on materials and workmanship is given with this FW Murphy product. A copy of the warranty may be viewed or printed by going to www.fwmurphy.com/support/warranty.htm BEFORE BEGINNING INSTALLATION OF THIS MURPHY PRODUCT: • Disconnect a
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents Introduction ............................................................................. 1 Engine and Transmission Parameters 2 Faceplate Features 3 Navigation and Keypad Functions 4 Operation ................................................................................. 9 PowerView Menus (First Time Start Up) 9 Setting Up the Display 12 Main Menu Options 18 Faults and Warnings 20 Utilities Menu 23 Modbus ® Setup 25 Selecting Engine ECU 26 Troubleshooting ..
Inhaltszusammenfassung zur Seite Nr. 4
(THIS PAGE INTENTIONALLY LEFT BLANK)
Inhaltszusammenfassung zur Seite Nr. 5
Introduction Congratulations on purchasing your PowerView display, a multifunction tool that provides a window into the many parameters and service codes of modern electronic engines and transmissions. This guide is intended to help you set up your PowerView display and identify navigation basics and product features. The display’s simple navigation and intuitive yet powerful features allow you to master the product in no time. Additional information can be found on our website at w
Inhaltszusammenfassung zur Seite Nr. 6
Engine and Transmission Parameters The following are some of the engine and transmission parameters which may be displayed in standard or metric units as well as in English, Spanish, French, Italian, or German languages (when applicable, consult engine or transmission manufacturer for SAE J1939 supported parameters): • Engine RPM • Transmission oil • Engine hours pressure • Transmission oil • System voltage temperature • Percent engine load at the current RPM • Transmission gear
Inhaltszusammenfassung zur Seite Nr. 7
Faceplate Features 00-02-0605 - 3 - Rev 09-10-08
Inhaltszusammenfassung zur Seite Nr. 8
Navigation and Keypad Functions The keypad on the PowerView display is a capacitive touch sensing system. There are no mechanical switches to wear or stick. When a key is touched, feedback is provided by the screen flashing. The keys on the keypad perform the following functions: Menu – Enter or exit menu screens. Left Arrow – Scroll the screen or move the parameter selection to the left or upward. Right Arrow – Scroll the screen and move the parameter selection to the right or
Inhaltszusammenfassung zur Seite Nr. 9
Basic Navigation 1. When Menu is pressed, the main menu items are displayed. 00-02-0605 - 5 - Rev 09-10-08
Inhaltszusammenfassung zur Seite Nr. 10
2. Touching the Arrow Keys will move the selection bar to other menu items. 00-02-0605 - 6 - Rev 09-10-08
Inhaltszusammenfassung zur Seite Nr. 11
3. Certain menus have multiple pages of items. Scrolling past the top item or bottom item on the current page will reveal other menu items on additional pages. 00-02-0605 - 7 - Rev 09-10-08
Inhaltszusammenfassung zur Seite Nr. 12
4. When the desired item is highlighted by the cursor, pressing Enter will select that item and display the corresponding screen. 5. Anytime the word MORE appears above the Arrow Keys there are more screens that may be viewed. Use the Arrow Keys to scroll to the next screen of information. 00-02-0605 - 8 - Rev 09-10-08
Inhaltszusammenfassung zur Seite Nr. 13
Operation PowerView Menus (First Time Start Up) 1. When power is first applied to the display, the Murphy logo appears. 00-02-0605 - 9 - Rev 09-10-08
Inhaltszusammenfassung zur Seite Nr. 14
2. If the Engine ECU is broadcasting a 'Wait To Start' message, this screen will be shown. Engine manufacturers typically recommend against starting the engine while this message is broadcasted from the ECU. Once the ECU stops broadcasting this message, this screen will no longer be displayed. 00-02-0605 - 10 - Rev 09-10-08
Inhaltszusammenfassung zur Seite Nr. 15
3. Once the engine has started, the single engine parameter appears with the engine RPM displayed. Pressing the Right Arrow Key will display the coolant temperature. The screen can be changed to other parameters by pressing Menu. 00-02-0605 - 11 - Rev 09-10-08
Inhaltszusammenfassung zur Seite Nr. 16
Setting Up the Display The screen may be configured to display a single engine parameter (1-up display), or four parameters at once (4-up display). Default options are provided or you may customize the display by selecting the parameters you want. 1-Up Display Three options are available for modification of the 1-Up display. Use Defaults – This option contains a set of engine parameters: Engine Hours, Engine RPM, System Voltage, Battery Voltage, % Engine Load at Current RPM, Coolant
Inhaltszusammenfassung zur Seite Nr. 17
1-Up Display Settings 1. Touch Menu and use the Arrow Keys to highlight SETUP 1-UP DISPLAY, then press Enter. 2. To select USE DEFAULTS, highlight the option and press Enter. A message indicating “RESTORED TO DEFAULTS” is displayed. 3. To select CUSTOM SETUP, highlight the option and press Enter. A list of engine parameters is displayed. 4. To select a parameter, use the Arrow Keys to scroll and highlight the parameter, then touch Enter. Selected parameters are indicated by a # sy
Inhaltszusammenfassung zur Seite Nr. 18
6. Continue to scroll and select additional parameters for the CUSTOM 1-UP DISPLAY. Touch Menu at any time to return to the CUSTOM SETUP menu. 7. Selecting the AUTOMATIC SCAN ON function will cause the 1-up display to scroll through the selected set of parameters one at a time. 8. Once the USE DEFAULTS, CUSTOM SETUP and AUTOMATIC SCAN functions have been set, touch Menu once to return to the main menu, or twice to display the 1-up display screen. 00-02-0605 - 14 - Rev 09-10-08
Inhaltszusammenfassung zur Seite Nr. 19
4-Up Display The 4-up display places the parameter data into four areas of the screen known as quadrants. Factory defaults for the 4-up display include coolant temperature, engine speed, oil pressure, and battery voltage. You may customize the 4-up display with parameters you define for each quadrant. 1. Touch Menu and use the Arrow Keys to highlight SETUP 4-UP DISPLAY, then press Enter. 2. To select USE DEFAULTS, highlight the option and press Enter. A message indicating “RESTORED TO
Inhaltszusammenfassung zur Seite Nr. 20
5. Touch Enter and a list of parameters will appear. The parameter that is highlighted is the selected parameter for the screen. The number to the right of the parameter indicates the quadrant in which it is displayed. 1 = upper left quadrant 2 = lower left quadrant 3 = upper right quadrant 4 = lower right quadrant 6. Use the Arrow Keys to highlight the new parameter to be placed in the quadrant that was selected in step 4 and touch Enter. 7. Touch Menu to return to the 4-UP
