Inhaltszusammenfassung zur Seite Nr. 1
TM
GlobalMap 2000
INSTALLATION AND
OPERATION INSTRUCTIONS
Inhaltszusammenfassung zur Seite Nr. 2
Copyright © 1997, 1998 Lowrance Electronics, Inc. All rights reserved. ™ GlobalMap 2000 is a trademark of Lowrance Electronics ® Lowrance is a registered trademark of Lowrance Electronics WARNING! USE THIS UNIT ONLY AS AN AID TO NAVIGATION. A CAREFUL NAVI- GATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN POSI- TION INFORMATION. Never use this product while operating a vehicle. CAUTION When showing navigation data to a position (waypoint), this unit will show the shortest, most direct path to th
Inhaltszusammenfassung zur Seite Nr. 3
GPS TABLE OF CONTENTS INTRODUCTION ......................................................................................................... 2 INSTALLATION .......................................................................................................... 2 BRACKET MOUNT ............................................................................................. 2 IN-DASH MOUNT ............................................................................................... 3 POWER CONNECT
Inhaltszusammenfassung zur Seite Nr. 4
DATUMS ............................................................................................................ 62 PCF (Position Correction Factor)................................................................ 64 POSITION FILTER .............................................................................................. 65 GPS SIMULATOR ............................................................................................... 65 PRESET ...............................................
Inhaltszusammenfassung zur Seite Nr. 5
The smallest hole that will pass the power plug is one inch. After the hole is drilled, pass the other cables up through the hole first, then pass the power cable down through it. After the cables have been routed, fill the hole with a good marine sealing compound. Offset the bracket to cover the hole. Route the cables through the slot in the back of the bracket. There are two “knockout” plugs in the rear of the bracket that can be removed to route cables, if necessary. MOUNTING - In-Dash Moun
Inhaltszusammenfassung zur Seite Nr. 6
RUBBER PAD RUBBER PAD BOLT BOLT LOWRANCE CAM CLAMP CAM CLAMP (TURNED DOWN) (TURNED UP) clamp on the right side of the unit is pointing up before you start tightening the bolts. POWER CONNECTIONS This product works from a twelve-volt battery system. For the best results, attach the power cable directly to the battery. You can attach the power cable to an accessory or power buss, however you may have problems with electrical interference. Therefore, it’s safer to go ahead and attach the power cabl
Inhaltszusammenfassung zur Seite Nr. 7
The wiring connections for the NMEA 0183 version 1.5 are different than the ones used for the NMEA 0183 version 2.0. If you are using version 1.5, then use the shielded green and red wires on the mapping unit’s NMEA cable. If you are using version 2.0, then you’ll be using all four shielded wires on the NMEA cable. If you’re using a Lowrance GPS module, simply plug its cable directly into the in-line connector on the mapping unit’s cable. This sends navigation data directly to the mapping unit
Inhaltszusammenfassung zur Seite Nr. 8
Lowrance Accessory Wiring Diagrams Since there are many different combinations of accessories that are used with the GlobalMap 2000, the drawings on the next four pages can help with the installation. (Note: The black connector on the GlobalMap 2000 is covered by a black plastic cap. Carefully pry this cap off to gain access to the connector.) The diagram on page 7 shows the GlobalMap 2000 connected to a Lowrance GPS receiver and DGPS receiver, and both 192 kHz and 50 kHz (SAM) sonar modules. In
Inhaltszusammenfassung zur Seite Nr. 9
7 LOWRANCE MAPLINK LOWRANCE GPS MODULE TO 12 VDC GLOBALMAP SAM-ST 2000 TO 12 VDC TO 192 KHZ DGPS DUAL TRANSDUCER FREQUENCY INTERFACE LOWRANCE SAM-50HPD DGPS BEACON RECEIVER WHITE WHITE TO GREEN GREEN SPEED/TEMP RED SENSOR TO BLUE 12 VDC BLACK BROWN TO 50 KHZ TO 12 VDC TRANSDUCER
Inhaltszusammenfassung zur Seite Nr. 10
8 LOWRANCE MAPLINK LOWRANCE GPS MODULE GLOBALMAP 2000 DGPS BEACON RECEIVER WHITE WHITE POWER CABLE GREEN GREEN RED TO BLACK RED 12 VDC BLACK TO 12 VDC
Inhaltszusammenfassung zur Seite Nr. 11
9 LOWRANCE MAPLINK LOWRANCE GPS MODULE GLOBALMAP SAM-ST 2000 TO 12 VDC TO 192 KHZ TRANSDUCER TO 12 VDC TO SPEED/TEMP SENSOR
Inhaltszusammenfassung zur Seite Nr. 12
NMEA 0183, VERSION 1.5 WIRING CONNECTIONS The shielded red and green wires are for a NMEA 0183, version 1.5 interface. The GlobalMap 2000 sends data to other electronic navigation devices through the green wire and receives NMEA data through the red wire. If the red and green wires are not used, tape their ends so that they cannot short. To connect a device to the mapping unit’s NMEA 0183 version 1.5 input (send data to the GlobalMap 2000), attach a twisted pair cable from the device’s NMEA out
Inhaltszusammenfassung zur Seite Nr. 13
NMEA 0183, VERSION 1.5 WIRING CONNECTIONS GLOBALMAP 2000 OTHER DEVICE'S NMEA 0183, NMEA CABLE VERSION 1.5 OUTPUT CABLE RED WIRE BLACK WIRE 12 VOLT BATTERY GLOBALMAP 2000 POWER CABLE GLOBALMAP 2000 RECEIVING NMEA 0183 VERSION 1.5 DATA FROM ANOTHER DEVICE GLOBALMAP 2000 OTHER DEVICE'S NMEA 0183, NMEA CABLE VERSION 1.5 INPUT CABLE GREEN WIRE BLACK WIRE 12 VOLT BATTERY GLOBALMAP 2000 POWER CABLE GLOBALMAP 2000 SENDING NMEA 0183 VERSION 1.5 DATA TO ANOTHER DEVICE 11
Inhaltszusammenfassung zur Seite Nr. 14
NMEA 0183, VERSION 2.0 WIRING CONNECTIONS WHITE (+) GREEN (-) TRANSMIT WIRES GLOBALMAP 2000 NMEA CABLE OTHER DEVICE'S BLACK (+) NMEA OUTPUT RED (-) GLOBALMAP 2000 RECEIVE NMEA 0183 VERSION 2.0 ONLY WHITE (+) RECEIVE WIRES GREEN (-) GLOBALMAP 2000 NMEA CABLE OTHER DEVICE'S NMEA INPUT BLACK (+) RED (-) GLOBALMAP 2000 SEND NMEA 0183 VERSION 2.0 DATA ONLY WHITE (+) RECEIVE WIRES GREEN (-) GLOBALMAP 2000 OTHER DEVICE NMEA CABLE BLACK (+) TRANSMIT WIRES RED (-) GLOBALMAP 2000 SEND AND RECEIVE NMEA 018
Inhaltszusammenfassung zur Seite Nr. 15
Connecting a LMS-350/350A to the GlobalMap 2000 To connect a Lowrance LMS-350 or LMS-350A with a GPS module to the GlobalMap 2000, first follow the wiring diagram at the bottom of this page. After all wiring is completed, plug the two units in and turn them on. On the LMS-350, then press the GPS key, then the MENU key. Now press the key next to the “Change GPS Settings” label. Press the key next to the “Select NMEA” label. The screen shown at right appears. Now press the key next to the “Selec
Inhaltszusammenfassung zur Seite Nr. 16
DGPS BEACON RECEIVER CONNECTIONS If a Lowrance GPS module is connected to the GlobalMap 2000, any brand of differential (DGPS) beacon receiver can also be connected, giving you higher accuracy positions in the area covered by the beacon receivers. The unshielded green and white wires on the POWER cable are used for the differential (DGPS) beacon receiver. (Note: You can also use the diagram on pages 7 or 8 if you’re using a Lowrance DGPS receiver.) To connect the beacon receiver, attach a twiste
Inhaltszusammenfassung zur Seite Nr. 17
The LOWRANCE LGC-1 GPS MODULE This GPS receiver is small, rugged, and fast. The five channel design lets it track all satellites in view and acquire up to five satellites at one time. It sends position information once every second. By incorporating Rockwell’s GPS receiver technology with Lowrance’s state-of-the-art design and manufacturing capabilities, Lowrance brings to the consumer one of the most advanced line of GPS marine navigation systems available in the world. LGC-1 GPS MODULE INSTALL
Inhaltszusammenfassung zur Seite Nr. 18
Surface Mounting - Without Access If you don’t have access to the back side of the mounting surface, use the “cleats” supplied with the GlobalMap 2000. (Note: This is assuming you can “snake” the module’s cable to a location that is accessible. A hole will still need to be drilled in the mounting surface for the cable.) Using the gasket as a template, mark and drill the 17 mm (11/16") hole for the cable. Attach the cable to the module and drop the other end of the cable through the gasket and
Inhaltszusammenfassung zur Seite Nr. 19
Pole Mount First, thread the pole mounting adapter onto the mounting pole or ratchet base. Align the pole mounting adapter so the module will face the bow of the boat. Install and tighten the set screw into the pole mounting adapter and tighten it securely. This should prevent the GPS module from unscrewing from the pole. Place the gasket onto the pole mounting adapter. Now attach the cable to the GPS module and pass the cable through the gasket, pole mounting adapter, and pole. Set the GP
Inhaltszusammenfassung zur Seite Nr. 20
SAM SONAR ACCESS MODULE In order for the GlobalMap 2000 to show sonar data, a sonar access module (SAM) and transducer must be installed. Follow the installation instructions included with the sonar access module. Route the cable from the sonar module to the black connector on the GlobalMap 2000. (Note: The black sonar connector on the GlobalMap 2000 is covered by a black plastic cap. Carefully pry this cap off to gain access to the connector.) Follow the installation instructions included with
