Inhaltszusammenfassung zur Seite Nr. 1
quick reference guide
®
EdgE 605/705
gPS-ENABLEd BIKE COMPUTER
MB
Inhaltszusammenfassung zur Seite Nr. 2
Warning : This product contains a lithium-ion battery. See the Important Safety and Product Information guide in the product box for important battery safety information. Warning : Always consult your physician before you begin or modify any exercise program. See the Important Safety and Product Information guide in the product box for product warnings and other important information. Buttons power ➊ • Press and hold to turn the Edge on/off. • Press to turn the backlight on/off. ➊ ➐ m
Inhaltszusammenfassung zur Seite Nr. 3
Resetting the Edge thumb stick/enter ➍ If your Edge is locked up/frozen, • Move the thumb stick to scroll press mode and reset/lap through menus, options, and data simultaneously to reset the Edge. fields. This does not erase any of your data • Press in the thumb stick to select or settings. options and to acknowledge messages. Icons start/stop Battery charge level ➎ Press to start/stop the timer. Battery charging menu ➏ Satellite icon changes from • Press to open the menu page. bl
Inhaltszusammenfassung zur Seite Nr. 4
Step 1: Charge the Battery You can charge the Edge using the AC charger or the USB cable and your computer. Mini-USB port under weather note: To prevent cap corrosion, thoroughly dry the mini-USB port, weather cap, and 3. Plug the other end into a surrounding area before standard wall outlet (AC) or charging or connecting to an available USB port on your computer (USB). a personal computer. To charge the Edge: Step 2: Install the 1. On the back of the Edge, Edge pull up the weat
Inhaltszusammenfassung zur Seite Nr. 5
be used under the mount for a better rubber pad also prevents the mount viewing angle. from slipping. Continue with step 2. 2. Attach the bike mount To install the Edge on your securely using two cable bike stem: ties. Make sure the cable ties 1. Place the wedge on the bike are threaded through both stem, and then place the bike parts of the bike mount. mount on the wedge. Make sure 3. Align the Edge with the bike the release lever is on the left. mount so that the Edge is Release Wed
Inhaltszusammenfassung zur Seite Nr. 6
4. Slide the Edge to the left Step 5: Save Your until it snaps into place. Home Location To release the Edge: (Optional) Press down on the release lever, and You can set a home location for the slide the Edge to the right. place you return to most often. 1. Press menu > select Step 3: Turn on Your Where To > Find Places > Edge Favorites > Go Home. Press and hold to turn on 2. Follow the on-screen instructions. your Edge. Follow the on-screen configuration instructions. Step 6: Set Up
Inhaltszusammenfassung zur Seite Nr. 7
3. Wrap the strap around your Heart Rate Monitor chest and attach it to the other Wear the heart rate monitor directly side of the heart rate monitor. on your skin, just below your breastplate. It should be snug enough note: The Garmin logo to stay in place during your run. should be right-side up. 1. Push one tab on the strap 4. Turn on the Edge and bring it through the slot in the heart rate within range (3 m) of the heart monitor. Press the tab down. rate monitor. The heart rate
Inhaltszusammenfassung zur Seite Nr. 8
mount and a cable tie. The GSC 10 pedal magnet must be within Both magnets must be aligned with 5 mm of the GSC 10 and the their respective indication lines for indication line on the pedal the Edge to receive data. magnet must line up with the To install the GSC 10: indication line on the GSC 10. 1. Place the GSC 10 on the rear 3. Unscrew the spoke magnet chain stay (on the side opposite from the plastic piece. Place the drive train). Loosely attach the spoke in the groove of the
Inhaltszusammenfassung zur Seite Nr. 9
Spoke magnet GSC 10 Pedal magnet Sensor arm indication line GSC 10 and magnet alignment not enough room between the then green. Pedal to test the sensor arm and the spoke. The sensor alignment. The red LED magnet must be aligned with blinks each time the crank arm the sensor arm indication line. passes the sensor, and the green LED blinks each time the wheel 4. Loosen the screw on the sensor magnet passes the sensor arm. arm and move it to within 5 mm of the spoke magnet. You can also
Inhaltszusammenfassung zur Seite Nr. 10
6. When everything is aligned To set your bike profile: and working correctly, tighten Press menu > select Settings > the cable ties, sensor arm, Profile & Zones > Bike Profile . and spoke magnet. Step 7: Set Set Y Your our Profiles The Edge uses information that you enter about yourself and your bike to calculate accurate ride data. To set your user profile: Press menu > select Settings > Profile & Zones > User Profile . Step 8: Go for a Ride! Press mode to view the bike computer page.
Inhaltszusammenfassung zur Seite Nr. 11
Step 9: Download Free More Information For more information about the Edge Software functions and settings, refer to the 1. Go to www.garmin.com/edge. owner’s manual. 2. Follow the on-screen instructions to download Garmin Training ® ™ Product Registration Center or Garmin Connect . Help us better support you by completing our online registration Step 10: Transfer today. Go to http://my.garmin.com. History to Your Keep the original sales receipt, or a photocopy, in a safe place. Comput
Inhaltszusammenfassung zur Seite Nr. 12
© 2007 Garmin Ltd. or its subsidiaries ® Garmin is a trademark of Garmin Ltd. or its subsidiaries, registered in the USA and other ® ® ™ ™ ™ ™ countries. Garmin Training Center , Edge , Garmin Connect , GSC 10, Dynastream , ANT , ™ and ANT+Sport are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. Other trademarks and trade names are those of their respective owners. Garmin International, Inc., 1200 East 151st Street,
