Inhaltszusammenfassung zur Seite Nr. 1
Dual GPS
DD-80
Inhaltszusammenfassung zur Seite Nr. 2
Your Local Agent/Dealer Your Local Agent/Dealer 9-52 Ashihara-cho, 9-52 Ashihara-cho, Nishinomi Nishinomiy ya, Ja a, Jap pan an Tele Telep phone : hone : 0798-65-2111 0798-65-2111 Telefax : Telefax : 0798-65-4200 0798-65-4200 F FIRST EDITION : IRST EDITION : DEC. DEC. 1995 1995 A All ri ll rig ghts reserved. hts reserved. Printed in Japan Printed in Japan J J :: APR. APR. 01,2003 01,2003 PUB.No. PUB.No. OME-43741 OME-43741 ( ( TENI TENI ) ) DD-80(GP-80-D) DD-80(GP-80-D) *OME43741J00* *OME43741
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY INSTRUCTIONS "DANGER", "WARNING" and "CAUTION" notices appear throughout this manual. It is the responsibility of the operator and installer of the equipment to read, understand and follow these notices. If you have any questions regarding these safety instructions, please con- tact a FURUNO agent or dealer. This notice indicates a potentially hazardous situation which, if not avoided, will result in death or DANGER serious injury. This notice indicates a potentially hazardous situation w
Inhaltszusammenfassung zur Seite Nr. 4
CAUTION WARNING Use the proper fuse. Hazardous voltage. Can shock. Use of a wrong fuse can result in fire or permanent equipment damage. Do not open the cover. Only qualified personnel should Power the equipment with the proper work inside the equipment. power supply. Powering the equipment with a wrong power supply can cause permanent equipment damage. WARNING Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. Turn off the power immediately if wat
Inhaltszusammenfassung zur Seite Nr. 5
4.5 Erasing Route Waypoints.................. 4-6 TABLE OF 4.6 Replacing Route Waypoints.............. 4-7 4.7 Erasing Routes .................................. 4-7 CONTENTS 5. SETTING DESTINATION 5.1 Setting Destination ........................... 5-1 FOREWORD............................................ iii 5.2 Cancelling Destination...................... 5-5 SYSTEM OVERVIEW ............................. 1 5.3 Erasing Route Waypoints (flags) ...... 5-6 5.4 Finding Range and Bearing Betwee
Inhaltszusammenfassung zur Seite Nr. 6
10. INTRODUCTION TO GPS APPENDIX C 10.1 What is GPS? ................................ 10-1 INSTALLATION OF GP-80-D 10.2 How the GPS Receiver General................................................... C-1 Calculates Position........................ 10-1 Display Unit........................................... C-2 10.3 What is Differential Antenna Unit.......................................... C-3 GPS (DGPS)? ............................... 10-2 Wiring ..............................
Inhaltszusammenfassung zur Seite Nr. 7
The main features of the DD-80 are FOREWORD • Comprehensive navigation data displays • Storage for 999 waypoints and 30 routes • Alarms: Arrival, Anchor Watch, Cross- A Word to DD-80 Owners track Error, Speed, Water Temperature, Depth, and Trip Congratulations on your choice of the • Man overboard feature records latitude and FURUNO DD-80 dual differential GPS navi- longitude coordinates at time of man over- gation system. We are confident you will see board and provides continuous updates of wh
Inhaltszusammenfassung zur Seite Nr. 8
This page is intentionally left blank.
Inhaltszusammenfassung zur Seite Nr. 9
SYSTEM OVERVIEW 1. Menu Tree Display selection menu DISPLAY Select Display (Plotter 1, Plotter 2, Highway, Navigation and Data displays) SEL Main menu MENU 1. DISPLAY SETUP ESC 2. TRACK/MARK SETUP 3. ERASE TRACK/MARK 4. ALARM SETTINGS 1/2 ALARM SETTINGS 2/2 5. MANUAL CALCULATION 6. 7. GPS MONITOR SATELLITE MONITOR BEACON RCVR MONITOR STATION MESSAGE 8. SELF TESTS 1. MEMORY, I/O PORT TEST 2. KEYBOARD TEST 3. TEST PATTERN 4. AU
Inhaltszusammenfassung zur Seite Nr. 10
Waypoint, route menu WPT 1. Cursor RTE 2. MOB/Event Position 3. Own Ship Position 4. Waypoint List WAYPOINT LIST 5. Route Planning ROUTE LIST GOTO menu GOTO 1. Cursor 2. MOB/Event Position 3. Waypoint List GOTO "Waypoint List" 4. Route List GOTO "Route List" 5. Cancel 2
Inhaltszusammenfassung zur Seite Nr. 11
2. System Configuration GP-80 GP-80 GPS GPS ANTENNA ANTENNA GPA-017S/018S/019S GPA-017S/018S/019S DISPLAY UNIT DISPLAY UNIT GPR-020 GPR-020 INTERFACE UNIT IF-2500 Position, etc. Arrival Cross track Abnormal receiving (Current loop) alarm error alarm alarm Position, waypoint, etc. (RS-422/Current loop) 3
Inhaltszusammenfassung zur Seite Nr. 12
3. Operation Flow Chart Select display mode • Plotter 1 (own ship's track and data) • Plotter 2 (own ship's track) • Highway (ship's track overlaid on navigation lane) • Navigation (graphic navigation data display for steering) • Data (alphanumeric navigation data) Set destination temporarily Register waypoints • By latitude and longitude • By LOP Register routes Set destination Display steering data Set alarms Perform other operations as required. (Position correction, geodetic chart to use
Inhaltszusammenfassung zur Seite Nr. 13
1. OPERATIONAL OVERVIEW 1.1 Control Description Cursor keys Shift display and cursor. MENU NU/CU Opens/closes menu; Selects display orientation; ESC ENT quits current operation. registers selections on menus. DISPLAY EVENT Inscribes event mark at Selects display mode. 6 SEL 1 MOB ship's position; marks man overboard position WPT GOTO Registers waypoints Sets destination. 2 RTE 7 and routes. PLOT MARK Inscribes mark on Turns recording and plotting 3 ON/OFF 8 the display. of ship's track on/off. Z
Inhaltszusammenfassung zur Seite Nr. 14
1.2 Turning On and Off the A Several seconds GPS receiving Power later condition The DD-80 takes about two minutes to find position when turned on for the very first time. 34° 23.456´ N 135° 45.678´ E DGPS 3D Other times it takes about 20 seconds. 30 BRG [01] 234° Note: The GPS provides highly accurate po- sition information. However, position should CSE always be check against other aids to naviga- 345° 40 50 tion to confirm reliability, for the safety of H RNG vessel and crew. 123 nm SPD 20 Tu
Inhaltszusammenfassung zur Seite Nr. 15
Note 1: When PDOP value exceeds 6 in 1.4 Display Mode the 3D mode, the position fixing method is automatically changed to 2D. 1) Press the [DISPLAY SEL] key. The dis- play shown in Figure 1-4 appears. Note 2: The "DEMO" icon appears when the display is in the demonstration mode. Select Display To return to normal mode, turn off the power and turn it on while pressing and Plotter 1 Plotter 1 holding down the [NU/CU ENT] key. Plotter 2 Highway Turning off the power Navigation Data Press the [POWER
Inhaltszusammenfassung zur Seite Nr. 16
Plotter 1 display Plotter 2 display Ship's position appears when cursor is off Bearing from own ship Cursor position or lighthouse to destination waypoint data Course GPS receiving Own ship's bar 34° 23.456´ N 135° 45.678´ E DGPS 3D condition track Own ship Alarm 30 mark range [01] 34° 23.456´ N 135° 45.678´ E DGPS 3D 40 30 50 BRG H [01] 234° CSE 20 40 345° 50 WGS84 H 2nm BRG TO + 123° Figure 1-6 Plotter 2 display RNG TO + 20 WGS84 2.0nm nm 11.5 Highway display Horizontal range Course Course Gr
Inhaltszusammenfassung zur Seite Nr. 17
2) Autopilot connection, automatic mode Navigation display 1) No autopilot connection DGPS 3D TO; 012 SPD E Cross track Bearing from own error meter ship to destination kt 12.3 waypoint N VTD Bearing Destination Speed BRG: scale Velocity To waypoint no. 10.3 kt Destination 63° CSE: S RNG 123° DGPS 3D 0.1nm 0.1nm TO; 012 123 nm E SPD TRIP kt 12.3 Auto Pilot Hdg Str 789 nm N Auto 123° P 23° VTD BRG 10.3 kt 63° CSE Auto mode S RNG Heading 123° 0.1nm 0.1nm Rudder angle Rudder angle 123
Inhaltszusammenfassung zur Seite Nr. 18
Data display Data to display and size of characters can be selected by the operator. Position in latitude and longitude or LOPs Fixing date and time* Cursor SEP 12, 1995 23:59'59" U DGPS 3D POSITION 12° 23.456' N WGS84 123° 23.456' E RNG BRG TO : 001 MARINE 223.4° nm 31.23 POINT1 SPD CSE NEXT : 002 MARINE kt 12.3 123.4° POINT2 User-defined User-defined Current destination waypoint display data #1 display data #4 Next destination waypoint User-defined User-defined display data #3 display data
Inhaltszusammenfassung zur Seite Nr. 19
2) Press the [9] key to display the SYSTEM Now transmitting data SETTINGS menu. SYSTEM SETTINGS MENU: Stop 1. PLOTTER SETUP 2. UNIT SETUP 2. UNIT SETUP 2. UNIT SETUP Figure 1-16 3. DATA 1, 3 OUTPUT SETUP 4. DATA TRANSFER 5) To stop transmitting data, press the 5. DATA 4 I/O SETUP [MENU ESC] key. The following display 6. GPS SETUP appears. 7. DGPS SETUP 8. LOP SETUP 9. CLEAR MEMORY Are you sure to stop ? ENT: Enter MENU: Escape ENT: Yes MENU: No Figure 1-17 Figure 1-13 SYSTEM SETTI
Inhaltszusammenfassung zur Seite Nr. 20
Transmission failure during 1.6 The Interface Unit operation The Interface Unit IF-2500 outputs data re- Data is transmitted only once. When trans- ceived from the navigators to external equip- mission error occurs, the following message ment. Operational status is shown by the LEDs appears. on the unit. For further details, see APPEN- DIX B of this manual. For how to select data Failed in transmitting to output, see paragraph 8.4 Outputting Data. Try "DATA TRANSFER" menu Press any key Output da
